The open-ended work-order trick: You may be very surprised if you allow work to proceed without signing a work order with a specified price. Or, you may sign a work order, and think you're protected against open-ended wallet-reaching, only to find a much higher price due at the finish than you expected, because you signed a "parts as needed" order that got loaded up with a long list of parts (that likely were still in serviceable condition). You might have been quoted a price, but then get a bill for that price plus a lot more added for the "service call" and the "parts", and be told the quote was just for the labor. While this is the normal way of abusing your finances down at the hospital, you shouldn't agree to it for a garage door service call. These guys are not doctors.
As we’ve mentioned before, springs are installed within your garage lift mechanism in order to help lift the door. Because doors are so heavy, the lift motor would undergo far more significant wear and tear if it had to lift the full weight of the door every time you opened it. Furthermore, in order to ensure that you can open your door even if you lose power in your home, springs allow you to lift the door by hand when the motor is disengaged.
To estimate the maximum physical force required to wind these springs, consider that they are balancing the weight of the door with a torque applied to a lift drum on each end of the torsion shaft. The lift drums have a 2-inch radius, which is the standard residential size, and corresponds conveniently to about a 1-foot circumference. If we pessimistically assume the 10-by-7-foot door has a weight of 350 pounds, this implies a torque of 350 pounds on a 2-inch radius, that is, 700 inch-pounds, or 58 foot-pounds. Each of the two springs should be exerting slightly less than half of the balancing torque, or 29 foot-pounds. Compare this to, say, the bolts in an automobile, which are typically torqued to values of about 50 foot-pounds, or tire lug nuts, which may be torqued to well over 100 foot-pounds.
Tools in Action says the Ryobi Ultra Quiet has plenty of versatility, as you can plug devices into the opener hardware, like a Bluetooth speaker, a fan, or even an 18V Ryobi cordless tool battery. When the opener has power, it will charge the battery. But if your home ever loses power, the 18V battery works as a backup to the garage door opener, allowing it to operate normally.
Uncentered center bearing plate: The center bearing plate need not actually be in the center. It doesn't much matter where it is, since the purpose of the bracket is to anchor the spring ends. This anchoring must be secure, since all the torsion is held together at that point. On a stud-framed wall, this bracket may be placed over the stud closest to the center rather than exactly at the center of the door opening.
I called late on a Monday and was able to get scheduled for 8:00 Tuesday morning. Matt arrived promptly on time and did a thorough assessment of the problem. He explained all my repair options and the advantages of each. I took his advice and opted for the door overhaul, in addition to the logic board replacement. The door was the original and had been installed improperly. There were wrong parts and incorrect assembly. Matt worked diligently to make things right. What was normally a two hour job took four, as he wouldn’t be satisfied with anything less than perfection. He stopped back by late in the afternoon to make sure all adjustments were made correctly. Excellent service, fair price, and explanations of every step in the repair process.read more
Because your garage door is a major entryway to your home, it is important to keep it in good working order for your own safety, security, and convenience. Choosing the right style and appropriate materials will lessen the amount of repairs that may arise. Additionally, investing in regular maintenance can be cost-effective in the long run. If your garage door is in need of major repair, it is best to call a professional garage door repair company for assistance. Typically, the company will charge for at least one hour for making a service call. However, the benefits of a professional repair job can well outweigh any costs, as a professional can ensure the safety, security, and proper operation of your garage door.
The optician's trick: The serviceman looks over your door with lots of scowling, chin-scratching, and tsk-tsking. You ask, "how much?" He replies with the fair price. If you don't flinch at that price, he says, "for the parts", while quoting a large additional cost for the labor. If you still don't flinch, he adds, "each," while pointing back and forth to your pair of springs. (I hope none of you service people are reading this!) I call this the "optician's trick" after the old vaudeville joke about lenses, frames, and left/right.
I obtained my parts, as described on this page, from American Garage Door Supply Inc. (http://www.americandoorsupply.com/) They may have raised their small-order prices or imposed a minimum order since I ordered from them in 2002 at the prices in my essay above. The Web site offers a free catalog by PDF download or mail. Springs in 2005 were priced at $2.25/lb.
You might not think it could get easier than pushing a big button to open a door, but some garage door openers make things even simpler by offering keyless entry and multiple remotes. Many models come with a keyless entry pad that mounts outside the garage door so you can gain access without a remote. While a remote is preferable for most situations, there are times when you need to get into the garage and don’t have it handy, so this is a nice feature to have.
Most garage door openers are pretty expensive. So if you need an opener on a budget, the Genie 1035-V (also known as the Genie Chain Drive 500) gives you that desirable low price point. It doesn't have a lot of high-end tech features, nor will it manage heavy garage doors, but it does the basic work of raising and lowering the garage door perfectly well.
Garage door openers manufactured and installed in the United States since 1982 are required to provide a quick-release mechanism on the trolley that allows for the garage door to be disconnected from the garage door opener in the event of entrapment.  Garage door openers manufactured since 1982 are also required to reverse the garage door if it strikes a solid object.
The wire size and winding direction are easily discovered and proved, as I will explain below. You absolutely must know and understand the critical measurements of your old springs to order replacements. This assumes that the old springs were the correct to begin with; it is not uncommon to have incorrectly sized springs on a door due to a previous sloppy installation, or a significant change in weight of the door.
Belt driven garage door openers offer a prime level of noise reduction if you want a silent environment in the garage. While common chainlinks will rattle during use, the smooth performance of a belt dampens noise as the garage door slides up and down. Using a 3/4 motor, the Genie SilentMax 750 will easily tackle any typical garage door while keeping the environment quiet and comfortable while in use.
Today's garage doors come with those door sensors, and if anything is in the path of the door the sensor detects it and raises the door back to the open position. These precautions are important for families with young children or pets. Even if you don't have a mini me or furry friend running around your yard, it's a good idea to have a garage door that is safe for you, your guests and your belongings.
I was careful not to assume that the previous installation correctly oriented the right- and left-hand springs on the correct sides of the center bearing plate. They could have been installed backwards by an incompetent installer, resulting in them having been wound looser (larger diameter coil) instead of tighter (smaller diameter coil) than when in their relaxed state, and if so I would have corrected them on the new installation. The proper orientation of the springs applies their reaction torque from tighter winding such that it turns the drums to lift the door. Verifying this is a rather simple exercise in mechanical visualization, but does require some care to be certain of correctness. If you were to install the springs backwards, and then start to wind them in the wrong direction, then the torsion bar will start winding the drums backwards, and not holding against the vise pliers, which should be obvious to inspection. Winding a spring backwards also tends to screw the spring off the cones; this error cannot proceed too far before the spring slips off the cones.
The belt-driven Chamberlain B970 garage door opener is powerful and well-featured. With a 1.25 HPS motor, it's got all of the strength needed for just about any residential garage door, and the motor and belt are covered by a lifetime warranty. The feature line-up includes built-in Internet connectivity for those who want to be able to monitor and operate their opener from afar, and a battery back up in the case of a power outage.
The Genie Chain Drive garage door opener combines The Genie Chain Drive garage door opener combines powerful reliable performance with smooth operation to create a long-lasting and easy-to-install garage door opener. The unit's electronic push-button programming makes installation and setup fast and easy. Complete with accessories the system features a reliable DC motor that delivers quiet smooth operation ... More + Product Details Close