The standard winding tools are simply a pair of 18-inch lengths of mild steel rod, 1/2-inch diameter. Winding cones can have different socket sizes (such as 5/8 inch instead of 1/2 inch), so it is important to measure the socket and select a matching rod diameter. Also beware that poor-quality cones may have a sloppy fit to the winding bars, and a loose fit presents a severe hazard of slipping at the worst moment; anything more than about an inch or two of play at the handle end is too loose for safety. I bought a 3-foot length of zinc-plated 1/2-inch diameter steel rod from Home Depot for about $3, which conveniently cuts into two halves of just the right length (the store might even cut it for you if you ask). A steel supplier selling at commodity prices might charge about 50 cents or so for such a piece that weighs about 2 lbs. Drill rod would work if used in the annealed condition in which it is originally sold, but the added expense provides no benefit and the brittleness (if it had been hardened and not annealed) would worry me a bit. Rebar, threaded rod, screwdrivers, etc., are absolutely foolish as they will not fit the socket snugly. Aluminum rod is definitely too weak, and will bend under the torque that must be applied. Longer rods would make for more leverage but unwieldly swing; shorter rods make for uncontrollable swing. As we'll calculate below, the 18-inch standard tool length is an appropriate compromise. Note that you do not need 18 inches of ceiling clearance above the torsion shaft to use an 18-inch rod, since you need not swing the rods above horizontal when winding.
Our technicians are specially trained to handle a variety of garage brands, styles, and configurations. After arriving at your home, a Sears technician will diagnose the problem and walk you through the options for fixing it. Next, the technician will make any necessary adjustments or replace broken parts to ensure the door can be operational once again. We always attempt to complete repairs the same day of service, and your satisfaction is guaranteed. Our representatives are standing by for your call and are happy discuss pricing options.

If you've researched this subject at all, you will no doubt have heard that you shouldn't be attempting torsion spring replacement as a do-it-yourselfer. That is generally good advice, so if you have any doubts about your abilities to do risky physical work on your own, hire the job out like everyone else. I found I was capable of doing this work with acceptable risk, because I intelligently understood the techniques, paid careful attention to methods and safety, knew how to use common tools in good condition, properly improvised the special tools I didn't have, and diligently attended to correctly performing a few moments of hazardous manipulation. I learned to do it purely on my own based mostly on bits of advice reluctantly given in Internet forums such as the Usenet newsgroup alt.home.repair. When I first wrote this page in 2002, there was no other do-it-yourself information available on the Web, and it was not until 2005 that reliable information disclosing the techniques started to appear elsewhere (see links below).
Extremely straightforward and efficient estimating and installation process. We purchased a Clopay sectional steel garage door for our double garage that works flawlessly with our existing door operator. The guys suggested an insulated door, but I thanked them and said no because I don't care for the garage to warm up in the winter and create a corrosive atmosphere of melting snow and salt. Great job!
Carriage: These doors mimic the look of doors found on old carriage houses in the days of horses and buggies. Because of their rustic look, they are often favored in the West and Southwest of the United States. The doors swing open like oversized French doors and hang from jambs on hinges. With their unique look, they create an area of visual interest for your home and are quite energy efficient. The downside is they require a considerable amount of clearance to work properly. Because most carriage garage doors are largely composed of wood, you may need to replace deteriorating or rotting door materials. The average cost for carriage garage door repairs is $133.

Wayne Dalton garage doors are some of the best in the industry. We offer a large selection of garage door designs in many colors and options that can drastically enhance your home’s curb appeal. Not only will a new garage door add beauty to your home, but replacing an old or outdated door with a new one can increase your home’s value. Did you know that year after year replacing the garage door is one of the top home improvement projects for return on investment? Purchasing a new garage door for your home is an excellent investment and we’ve made it even easier to find the perfect door with our Garage Door Design Center or Garage Door Selection Guide.
Winding "up" starts out easy. It finishes at the proper number of turns, by which time you are pushing against the maximum torque. Count the turns of spring winding from when the springs are slack. To be sure you're winding the right direction, all you have to remember is that proper winding makes the spring smaller in diameter and longer in length as it twists "in". On the standard door (most common), this means you push the winding bars up to wind up the spring, which is an easily remembered rule. This is very apparent and should be verified during the first few easy turns. You can also think about the correct winding direction in mechanical terms, namely which way the reaction of the spring will torque the shaft and drums, which in turn will lift the cable. This should all make perfect sense before you attempt the manipulations.

Correct spring size is determined by factors such as the weight and height of the door. You cannot substitute a different spring and just tighten or loosen the winding to make it balance the load. Why? To maintain cable tension under all operating conditions, the spring must retain about one turn of unspent wind-up at the top-of-travel position, which with the lift drum size and door height predetermines the number of turns of winding at the bottom-of-travel; and furthermore the torsion of the fully-wound spring at the bottom-of-travel must be slightly less than that needed to lift the weight of the door when translated by the lift drums.
The Heavy Duty Chain Extension Kit for 10 The Heavy Duty Chain Extension Kit for 10 ft. High Garage Doors is required for reliable everyday operation of Chamberlain heavy duty chain drive models in 10 ft. garage door applications. Featuring a quick-install extension rail and replacement chain the kit includes everything needed for quick and easy installation. Includes ...  More + Product Details Close
I was having an issue with my garage door that turned out to simply be the remote lockout being accidentally engaged. I called Aaron’s Garage Door Service and rather than sending a tech out and charging me for such a simple problem, they explained the solution over the phone. I really appreciate businesses with a sense of integrity like that! If I ever have a real garage door problem, I will absolutely be calling these guys!
Clopay® is proud to be the largest manufacturer of residential garage doors in North America and recognized as the leading brand among homeowners. For more than 50 years, we have helped homeowners reimagine their homes and create a personalized exterior that they can enjoy and take pride in for years to come. Clopay’s residential garage doors are designed and manufactured in the USA, starting at our headquarters in the heart of Ohio, and delivered to dealers via our 50 distribution centers throughout the US and Canada.
Tools in Action says the Ryobi Ultra Quiet has plenty of versatility, as you can plug devices into the opener hardware, like a Bluetooth speaker, a fan, or even an 18V Ryobi cordless tool battery. When the opener has power, it will charge the battery. But if your home ever loses power, the 18V battery works as a backup to the garage door opener, allowing it to operate normally.
Unmatched or mismatched spring pair: You may find that you have a pair of springs that are different sizes. This mismatch may be a normal application, since the total torque on the torsion shaft is simply the sum of the torque contribution of each spring (indeed, very large doors can be lifted with 4 or more springs along the torsion shaft). The sum of the torque rates determine the lift; and dividing the torque among multiple springs does not change this. Some repair shops even apply mismatched pairs deliberately, since a few stock sizes of springs can be combined to fit a wider range of door weights than only matched pairs. For example, a technician may carry springs in increments of 20 lbs of lift, and when using pairs this allows a 20 lb increment in possible choices instead of 40 lb increments. Or, one spring from a pair may have broken and been replaced with a spring of equal torque rate but different size than the original.
As a first time homeowner, Home advisors is an invaluable tool! There is a steep learning curve that comes with buying a house!!!! Being able to have access to unbiased information is great! It really helps to have a basic idea of what costs are, and all the different things that go into each project. who knew that there was so much to consider when looking to replace garage doors!!!!

Finding the best rated garage door openers is a bit of a challenge. Quality professional reviews are currently hard to come by, and we did not spot any that addressed current models. About the only credible, current, testing-based feedback we spotted was from Wirecutter, and it addressed smart garage door controllers rather than openers. That said, if you would like to add smart features to an existing garage door opener that you are otherwise perfectly happy with, the review is worth a read.


Squealing, screeching, or grinding noises from your garage door are usually indicative of a lack of lubricant or an accumulation of dirt or debris in the tracks. When removing debris, do not use harsh chemicals to clean the tracks. Once the track is clean, coat it with lubricant designed especially for garage doors, if possible. If you do not have access to this special type of lubricant, you can use WD-40 on the tracks and hardware.
Finding the best rated garage door openers is a bit of a challenge. Quality professional reviews are currently hard to come by, and we did not spot any that addressed current models. About the only credible, current, testing-based feedback we spotted was from Wirecutter, and it addressed smart garage door controllers rather than openers. That said, if you would like to add smart features to an existing garage door opener that you are otherwise perfectly happy with, the review is worth a read.
Speed of a thrown winding bar:: The springs, being in balance with the door, effectively are able to launch a typical 150 lb door at 10.6 mph speed. An 18-inch long by 1/2-inch diameter steel winding bar happens to weigh about 1 pound. Since momentum is conserved, this 150:1 ratio in weight of the door to the winding bar means the fully-wound springs could potentially throw a winding bar at 10.6 mph * 150 = 1590 mph = 2332 ft/sec, assuming the energy were perfectly coupled and transferred. If the energy transfer were only 1/3 efficient, this would still be the 800 ft/sec speed of a typical pistol bullet. Except it is a foot-and-a-half metal spear, not a bullet.
Garage doors are the largest moving object inside your home. If you have a problematic garage door, it compromises the safety of your family and home. Overhead Door Company of Atlanta is a professional company you can count on. We provide you with quality service at a reasonable price. We offer FREE estimates on replacement garage doors and are spring replacement specialists. 24 hours a day 7 days a week we are your number one garage door repair service.
At this point I weighed the unlifted door to confirm and fine-tune my calculations. This is not strictly necessary, but it makes the adjustments easier to perform, if you happen to have a scale with the requisite capacity. With some helpers, we first lifted the door a few inches and rested it on blocks of wood to provide clearance underneath. Then I slid a 400-pound-capacity freight scale under the center of the door, we lifted again to remove the blocks, and lowered the door gently onto the scale. This door weighed in at 238 pounds, which is very heavy for a single-car door. Since the outside of the door carries the 3/4-inch plywood paneling to match the house, and that plywood weighs about 2 lbs/sq-ft, I estimate the door weight to be about 7 x 10 x 2 = 140 lbs of paneling with the rest 238 - 140 = 98 lbs the interior panels, hardware, and cobwebs. Knowing this total weight will help later in adjusting the torsion on the springs. After weighing, we removed the scale and blocks, leaving the door fully lowered again. Had I not had a high-capacity freight scale, I might have improvised a crude weighing device from levers and smaller weights of known mass, or a lever arm pressing a reduced proportion of the full weight onto a lower-capacity scale. Another factor to remember is that The weight of a wood door can vary with humidity.
Insulation increases the efficiency of your door and can lower your electric will. You need R-value garage doors. These type of doors keep out hot and cold air and also provide a sound barrier between the outside and your garage. Insulated doors use polyurethane or polystyrene foam as insulation inside the door. More information about garage door replacement cost.
Align the upper roller tracks by carefully lifting the door halfway. Lock it in place with two locking pliers, and install the supporting brackets on the back of the rails using 1-1/4 in. perforated angle iron (available at home centers and hardware stores). Install 1-1/2 x 1/4 in. stop bolts, with the threads to the inside of the track, at the end of each upper track.

Winding "up" starts out easy. It finishes at the proper number of turns, by which time you are pushing against the maximum torque. Count the turns of spring winding from when the springs are slack. To be sure you're winding the right direction, all you have to remember is that proper winding makes the spring smaller in diameter and longer in length as it twists "in". On the standard door (most common), this means you push the winding bars up to wind up the spring, which is an easily remembered rule. This is very apparent and should be verified during the first few easy turns. You can also think about the correct winding direction in mechanical terms, namely which way the reaction of the spring will torque the shaft and drums, which in turn will lift the cable. This should all make perfect sense before you attempt the manipulations.

Winding "up" starts out easy. It finishes at the proper number of turns, by which time you are pushing against the maximum torque. Count the turns of spring winding from when the springs are slack. To be sure you're winding the right direction, all you have to remember is that proper winding makes the spring smaller in diameter and longer in length as it twists "in". On the standard door (most common), this means you push the winding bars up to wind up the spring, which is an easily remembered rule. This is very apparent and should be verified during the first few easy turns. You can also think about the correct winding direction in mechanical terms, namely which way the reaction of the spring will torque the shaft and drums, which in turn will lift the cable. This should all make perfect sense before you attempt the manipulations.

There’s another reason new doors are superior to old ones: energy efficiency. Keep in mind, garage doors are large, and when they open, they let a lot of outside air into your home. While you may have significant insulation separating your garage from the rest of your home, eventually that temperature differential will start to influence your energy bills.


Clearly there is a lot going on with your garage door and it takes trained and qualified experts to properly install, maintain, repair, and replace them. The experts and On Track Garage Door Services have the tools, skills, training to get your garage door fixed the first time. In addition we can help you fix your garage door affordably and offer many options from your basic garage door to custom wood styles. To find out how much your garage door repair will cost, give us a call at 480-641-2301 or use our Contact Page.
Spring rate, torque, and lift: The spring rate K for these measurements is π*28.5*10^6 * (0.273)^4 / (32 * 140 * 1.72) = 64.5 IPPT. Applying 7.5 turns on this rate will yield a torque of 7.5 * 64.5 = 484 in-lb, which on the 4-inch drums (2-inch radius) yields a lift of (484 in*lbs)/(2 in) = 242 lbs. Again we find good agreement with the approximate door weight of 238 lbs.
Recently another type of opener, known as the jackshaft opener, has become more popular. This style of opener was used frequently on commercial doors but in recent years has been adapted for residential use. This style of opener consists of a motor that attaches to the side of the torsion rod and moves the door up and down by simply spinning the rod. These openers need a few extra components to function safely for residential use. These include a cable tension monitor, to detect when a cable is broken, and a separate locking mechanism to lock the door when it is fully closed. These have the advantage that they free up ceiling space that an ordinary opener and rail would occupy. These also have the disadvantage that the door must have a torsion rod to attach the motor to.
Garage door openers make it easy to get your garage open without the struggle or the hassle of facing inclement weather. The latest garage door openers have new features such as timed close, battery backup and improved energy efficiency. Sears carries top-of-the-line garage openers that can run much more quietly and smoothly than old models. With a keypad feature, you'll be able to get into your house using a secure four-digit code. With a few new batteries in your remote, you'll be opening your garage with the push of a button.
My door opener disengaged from the garage door. I made a call in late morning and was given an appointment for late the same afternoon. I received a call in early afternoon asking if I would like an earlier service call. Upon arriving the repair man introduced himself and explained that he would need a few minutes to assess the problem and perform an inspection. When he finished he provided me with a through explanation of the problem, the corrective measures he would take and some suggestions to improve operation. We discussed some options, agreed on the cost and the work was complete within a reasonable time frame. The door operates quieter and with less strain than it ever has. Pleasant, friendly, on-time and reasonably priced. Problem solved. It doesn't get any better than that.
We guarantee same day garage door service on calls placed by 1:00 pm. We are on most jobs within 2 hours of the request for service being placed. All our technicians travel in fully stocked trucks to your home or business to enable us to complete nearly all overhead / garage door repairs on the first trip without the need for additional appointments just to complete the job. We guarantee to exceed the normal service appointment you have experienced with other garage door companies by implementing the Absolute 22-point inspection on all jobs that we take on. Our 22-point safety inspection ensures the customer that all vital mechanical and safety parts of the door are fully operational and functioning as they should be. This prevents any future service calls for our customer and in turn saves YOU, the customer, money!
Garage remotes work by sending a coded signal via radio frequency to the garage door opener. If this code matches that of the opener, then the motor will operate and raise or lower the door. Older devices use a single coded switch, whereas newer systems utilise a rolling code that changes each time the remote is used, increasing the security of the door by offering billions of combinations.
The Keychain Garage Door Remote offers portable control The Keychain Garage Door Remote offers portable control with the highest level of security. Featuring a three-button design this compact remote controls up to three garage door openers individually. Easily programmed and compatible with nearly every garage door opener made by Chamberlain LiftMaster and Craftsman it’s the easy option for ...  More + Product Details Close
Garage door openers make it easy to get your garage open without the struggle or the hassle of facing inclement weather. The latest garage door openers have new features such as timed close, battery backup and improved energy efficiency. Sears carries top-of-the-line garage openers that can run much more quietly and smoothly than old models. With a keypad feature, you'll be able to get into your house using a secure four-digit code. With a few new batteries in your remote, you'll be opening your garage with the push of a button.
GUESS YOU DON’T CARE to reply to my emails, so I'm posting it up here..... On Sep 8, 2018, at 2:52 PM, Joe Turiczek wrote: Thanks for the invoice, thanks for the service, thanks for the rapid response, thanks for Chris (the tech), but one note….. I’m a really handy guy, I repair and maintain nearly everything around the house, I am very mechanically adept, and I am also a highly skilled technical person that runs my own business by trade. I would have and could have repaired the belt myself, but I am traveling for business sooner than I could have ordered a belt, and did the repair….which means, I looked at the belts, I watched all the videos, it’s an EASY repair. I have belts down to a science, I’m really not an armchair DIY repair guy, I’m pretty good……That being said, I also shopped for prices of new belts for at least 30 mins or better, across easily 20-30 different parts and/or repair websites. Why am I telling you this? Because I think Chris, and your labor prices are spot on, and he deserved every cent, and your labor billing is more than fair…..however, I think your charge for the belt is a bunch of crap, it is nearly double of the HIGHEST price I found, which was $20-$25 higher than the average prices I found. Based on that alone, there is no way I could recommend, your otherwise FANTASTIC service, to anybody I know with a straight face. That’s just me being honest, because that’s who I am.

If you haven’t looked at garage doors lately, prepare to be pleasantly surprised. We’ve taken the garage door and made it stylish with designs to complement both classic and contemporary homes while still keeping the functionality you desire. A garage door can represent more than 30% of your home’s curb appeal, which makes choosing the right design especially important – and Home Depot has the widest selection available. With over 1,000 different garage door designs in wood, steel, composite, aluminum and glass, you’re sure to find the perfect style to transform your garage… and your home.


Squealing, screeching, or grinding noises from your garage door are usually indicative of a lack of lubricant or an accumulation of dirt or debris in the tracks. When removing debris, do not use harsh chemicals to clean the tracks. Once the track is clean, coat it with lubricant designed especially for garage doors, if possible. If you do not have access to this special type of lubricant, you can use WD-40 on the tracks and hardware.
Most wood doors are sectional roll-up doors, though a swing-up wood door that’s meant to be painted can be affordably built in the driveway from a wood framework and plywood. Custom wood doors are typically made of durable softwoods such as Douglas fir, cedar, redwood or cypress, or from hardwoods such as oak or mahogany. Appearance-grade hardwoods are relatively expensive.
The garage door opener traditionally has been a simple device. And it still is for the most part. But as with a lot of household items, technological advances are finding their way into garage door opener hardware. There are quite a few cool features in modern garage door openers, some of which are things you never knew you needed to automate the process of opening and closing a garage door.
While many sites may encourage you to save on garage door replacement costs by installing the door yourself, this is severely discouraged due to safety concerns and the installation techniques and tools required to properly and efficiently replace a garage door. When installing a new garage door, the range of prices also includes the labor performed by the professional garage door technician. These costs can include:
Your ad had no cheap coupons or promises.. Just business. Service was more than prompt. No attempt to fix something that was not broke or did not try to sell me anything I did not need. He stated the price at the beginning and stuck to it. (I was so pleased, I did not bother to mention a senior discount.) Very, very pleased that I have found someone I can trust and rely on. GaryRichard
Capable of lifting a seven-foot garage door up to 500 pounds in weight, the SilentMax 750 comes with a number of convenience features for automatic and remote use. The included wireless keypad and dual remote controls will ​insure that you are the only one that has access to the door. Compatible with a number of in-car remote systems like HomeLink, you can also keep the remotes at home if you are worried about losing the “keys.”​
Smartphone Control: Many newer garage door openers allow you to connect the device to your home's Wi-Fi network, according to RW Garage Doors. You then can open and close the door through a smartphone app. In fact, many of these apps will give you an alert on the smartphone when the garage door is open for a certain period. Some opener models even can connect to your existing Smart Home system, incorporating all your appliances on one system.

Garage Door Opener Co

×