I mentioned earlier that this apparatus had at least one prior spring replacement, with a single longer spring having been replaced by two shorter springs. The clamping of the original spring had pressed dimples and an eccentric distortion into the hollow shaft. While this distortion was large enough to block the old cones from sliding across, I was able to remove the old hardware by just sliding them in the other direction. I did not have to bother trying to press out this distortion, since I could just work around it.
The "liability" angle: The flip side of "safety issue" is "liability". This is not used to directly sell you something; it is used to demean the cheaper alternative and prod you into buying a more expensive (and profitable) option. For example, you may be pressured into buying a whole new door, when you just need a new spring, by the salesman telling you he can't just replace the spring due to "liability" issues. Since product liability is a big burden on the garage door industry, and so many old doors (and especially automatic openers) are dangerous, this may be a genuine reason to accept a higher price.
The Heavy Duty Chain Extension Kit for 10 The Heavy Duty Chain Extension Kit for 10 ft. High Garage Doors is required for reliable everyday operation of Chamberlain heavy duty chain drive models in 10 ft. garage door applications. Featuring a quick-install extension rail and replacement chain the kit includes everything needed for quick and easy installation. Includes ...  More + Product Details Close
The Heavy Duty Chain Extension Kit for 8 The Heavy Duty Chain Extension Kit for 8 ft. High Garage Doors is required for reliable everyday operation of Chamberlain heavy duty chain drive models in 8 ft. garage door applications. Featuring a quick-install extension rail and replacement chain the kit includes everything needed for quick and easy installation. Includes ...  More + Product Details Close
Another moment of truth arrives as the winding-up of the springs begins. (I am just posing here with the camera held out in my left hand. Except for lifting the door onto the scale, this was a one-man job, including the photography.) The position of the bars in this photo was necessary to take the photo, and does not show a correct winding technique, You should not have to swing the bar up as high over the top as shown. The lower bar during winding should swing from pointing down to pointing a little past horizontal. Then you hold that bar horizontal while socketing the other bar pointing down, apply force to that (now) lower bar, then remove the (now) upper bar, wind one-quarter turn, and repeat.

Disclosure: This post is brought to you by the Insider Picks team. We highlight products and services you might find interesting. If you buy them, we get a small share of the revenue from the sale from our commerce partners. We frequently receive products free of charge from manufacturers to test. This does not drive our decision as to whether or not a product is featured or recommended. We operate independently from our advertising sales team. We welcome your feedback. Email us at [email protected]


The open-ended work-order trick: You may be very surprised if you allow work to proceed without signing a work order with a specified price. Or, you may sign a work order, and think you're protected against open-ended wallet-reaching, only to find a much higher price due at the finish than you expected, because you signed a "parts as needed" order that got loaded up with a long list of parts (that likely were still in serviceable condition). You might have been quoted a price, but then get a bill for that price plus a lot more added for the "service call" and the "parts", and be told the quote was just for the labor. While this is the normal way of abusing your finances down at the hospital, you shouldn't agree to it for a garage door service call. These guys are not doctors.

Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.
Overhead Door® openers​ and garage doors are built with longevity in-mind. By performing a few routine tasks, you can help ensure your garage door system stays safe and stands the test of time. One important part of garage door system routine maintenance is to make sure the photo-eyes have not gone out of alignment. The photo-eyes are the infrared sensors which monitor whether the space at the bottom of your garage door is clear. When these sensors are not lined up properly they will keep your door from closing. Make sure to occasionally check your photo-eyes’ alignment to ensure they are correctly detecting obstructions to keep your garage door safe and operating properly.
Direct Drive - Unlike chain- and belt-driven systems, where the motor remains stationary while moving a chain, a direct drive motor moves while the chain stays in place. Because of this, the only moving part is the gear the motor uses to move while lifting the door. To our knowledge, only one company makes direct drive garage door openers: Sommer. The company claims the motors are more efficient and quieter than any other type of opener. However, this is the most expensive type of opener we’ve found, costing around $286 on average.
Location, climate and building codes are just a few factors to consider when determining which type of garage door is right for your home. Depending on the region you live in, you may need to choose a wind load option for your garage door. Wind loaded garage doors help safeguard your home in high wind prone areas. With garage doors serving as the largest and often times the primary entrance to the home, an insulated garage door may also be right for you.
While there might not be a huge price range when it comes to garage door openers—they are all quite an investment—there a few less expensive options to consider. Here’s a great budget option from Chamberlain. It has a motor that’s equivalent to ½ horsepower and chain drive system that is quick and easy to install. You can also connect it to the MQ technology (gateway sold separately) to use with your smartphone. The product comes with two three-button visor remote controls, a multi-function wall control, as well as a wireless keyless entry system. It comes with a 10-year motor, two-year parts, and one-year accessories warranty.
Some of the best garage door openers offer special features like a backup power source or a timer that automatically closes the door behind you at a predetermined time. While the door openers we reviewed vary in terms of power, noise and efficiency, they are all effective in the all-important task of letting you come and go with the simple push of a button. Here are the criteria we used to rank the top garage door openers:
Speed of a thrown winding bar:: The springs, being in balance with the door, effectively are able to launch a typical 150 lb door at 10.6 mph speed. An 18-inch long by 1/2-inch diameter steel winding bar happens to weigh about 1 pound. Since momentum is conserved, this 150:1 ratio in weight of the door to the winding bar means the fully-wound springs could potentially throw a winding bar at 10.6 mph * 150 = 1590 mph = 2332 ft/sec, assuming the energy were perfectly coupled and transferred. If the energy transfer were only 1/3 efficient, this would still be the 800 ft/sec speed of a typical pistol bullet. Except it is a foot-and-a-half metal spear, not a bullet.
When ordering springs, be aware that a number of different sizes of springs will make proper replacements, not just the specific size being replaced. The wire size, winding diameter, and length can be traded off to make springs of varied geometry but equivalent torque characteristics. This will also affect the expected lifetime (in cycles) for the spring(s). Since the critical specification for a replacement is the weight it is designed to bear, not the sizes per se, there are likely several stock sizes that replace a given old spring. The spring distributor's inventory may happen to offer only a different size with an equivalent weight-bearing specification. One has to judge whether to trust the advice of the seller in such situations. The seller should have the data to know what substitutions are proper.
Align the upper roller tracks by carefully lifting the door halfway. Lock it in place with two locking pliers, and install the supporting brackets on the back of the rails using 1-1/4 in. perforated angle iron (available at home centers and hardware stores). Install 1-1/2 x 1/4 in. stop bolts, with the threads to the inside of the track, at the end of each upper track.
The Genie Chain Drive garage door opener combines The Genie Chain Drive garage door opener combines powerful reliable performance with smooth operation to create a long-lasting and easy-to-install garage door opener. The unit's electronic push-button programming makes installation and setup fast and easy. Complete with accessories the system features a reliable DC motor that delivers quiet smooth operation ...  More + Product Details Close
×