Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.
GUESS YOU DON’T CARE to reply to my emails, so I'm posting it up here..... On Sep 8, 2018, at 2:52 PM, Joe Turiczek wrote: Thanks for the invoice, thanks for the service, thanks for the rapid response, thanks for Chris (the tech), but one note….. I’m a really handy guy, I repair and maintain nearly everything around the house, I am very mechanically adept, and I am also a highly skilled technical person that runs my own business by trade. I would have and could have repaired the belt myself, but I am traveling for business sooner than I could have ordered a belt, and did the repair….which means, I looked at the belts, I watched all the videos, it’s an EASY repair. I have belts down to a science, I’m really not an armchair DIY repair guy, I’m pretty good……That being said, I also shopped for prices of new belts for at least 30 mins or better, across easily 20-30 different parts and/or repair websites. Why am I telling you this? Because I think Chris, and your labor prices are spot on, and he deserved every cent, and your labor billing is more than fair…..however, I think your charge for the belt is a bunch of crap, it is nearly double of the HIGHEST price I found, which was $20-$25 higher than the average prices I found. Based on that alone, there is no way I could recommend, your otherwise FANTASTIC service, to anybody I know with a straight face. That’s just me being honest, because that’s who I am.

Trading diameter for length: Observe that in the spring rate formula in the table above, factors D (diameter of coils) and N (number of coils) appear together in the denominator of the spring rate formula. Algebraically, given equal wire sizes, this means that the product of the coil diameter and overall length produces the spring torque, not the diameter or length alone. Physically, this means that you can trade off torsion spring coil diameter versus overall length in inverse proportions to maintain the same torque rate. Trade-off example: A spring with 2-inch diameter coils that is 36 inches long equals a 1.5-inch diameter spring that is 48 inches long, because the product in both cases is 72 (inches squared). This assumes that wire size is equal in the trade-off, and that you have not counted dead coils in the length. Service technicians use this principle to make quick substitutions for what's on their truck versus what you need. But if you understand this, you're ahead of many technicians who don't know this trick. Maybe now you can educate the next one you hire.
Thank you for visiting Precision Garage Door Service of Seattle. We specialize in the repair of residential garage doors, openers, sales, service, & installation. Where ever you live along the Wasatch front, You have my personal guarantee that your experience with us will be professionally handled from start to finish. Your service will be provided by qualified & certified technicians that have completed the most extensive & rigorous training in the industry. We are proud of our environmentally sensitive business practices. Please give us a call to discuss your specific needs. We look forward to serving you.

Smart garage door openers aren't as expensive or hard to find as you might think. In fact, no matter what smart home platform you're using, there is an opener that will work for you. Smart garage door controllers add convenience like remote access, voice control, scheduling and vehicle detection to your garage door. You'll never need to wonder if you left it open ever again. 
One can overwind the springs slightly, up to about 8 turns on a standard residential door (that is, 1/2 or 3/4 extra turns), to compensate for undersized or fatigued springs, or increased door weight from painting or humidity, but this results in more stress on the springs and therefore decreased lifetime. If the door is too heavy for that slight tweak, then different springs are needed.
The history of the garage door could date back to 450 BC when chariots were stored in gatehouses, but in the U.S. it arose around the start of the 20th century. As early as 1902, American manufacturers—including Cornell Iron Works—published catalogs featuring a "float over door." Evidence of an upward-lifting garage door can be found in a catalog in 1906.[4]
And for some extra features, you'll appreciate accessing the system through the MyQ smartphone app. You can set up this Chamberlain opener to automatically close the door after 1, 5, or 10 minutes, which is great for people who are a bit forgetful. We also really like the motion-detecting control panel, which turns on lights whenever it records nearby movement.
Technician Mark called 1/2 hr before coming. Very knowledgeable and friendly technician. Originally scheduled as a tune-up but after pointing out several potential problems I decided on the complete overhaul package. All parts were on the truck. Technician completed job in a little over an hour. Very satisfied. Definitely would recommend.Bob PNorth Myrtle Beachread more
As your Kentucky and Ohio garage door repair company, we offer a team of experienced and knowledgeable technicians who move with urgency to diagnose your issues of any garage door repair or service They’ll discuss your options, and then execute the option you’ve selected for your home. When you need the best in garage door service, installation and repair, choose AE Door & Window.
Here are the new replacement springs I ordered from a distributor, which I found using a Google search for "garage door supply" (search that phrase now). You certainly won't find these at Home Depot or Lowe's (although last I checked Lowe's does carry the less daunting extension spring replacements). I also have a list of some suppliers at the end of this page.
The Keychain Garage Door Remote offers portable control The Keychain Garage Door Remote offers portable control with the highest level of security. Featuring a three-button design this compact remote controls up to three garage door openers individually. Easily programmed and compatible with nearly every garage door opener made by Chamberlain LiftMaster and Craftsman it’s the easy option for ...  More + Product Details Close
Winding "up" starts out easy. It finishes at the proper number of turns, by which time you are pushing against the maximum torque. Count the turns of spring winding from when the springs are slack. To be sure you're winding the right direction, all you have to remember is that proper winding makes the spring smaller in diameter and longer in length as it twists "in". On the standard door (most common), this means you push the winding bars up to wind up the spring, which is an easily remembered rule. This is very apparent and should be verified during the first few easy turns. You can also think about the correct winding direction in mechanical terms, namely which way the reaction of the spring will torque the shaft and drums, which in turn will lift the cable. This should all make perfect sense before you attempt the manipulations.

Garage door openers manufactured and installed in the United States since 1982 are required to provide a quick-release mechanism on the trolley that allows for the garage door to be disconnected from the garage door opener in the event of entrapment. [8] Garage door openers manufactured since 1982 are also required to reverse the garage door if it strikes a solid object.[9][10]
At this point I weighed the unlifted door to confirm and fine-tune my calculations. This is not strictly necessary, but it makes the adjustments easier to perform, if you happen to have a scale with the requisite capacity. With some helpers, we first lifted the door a few inches and rested it on blocks of wood to provide clearance underneath. Then I slid a 400-pound-capacity freight scale under the center of the door, we lifted again to remove the blocks, and lowered the door gently onto the scale. This door weighed in at 238 pounds, which is very heavy for a single-car door. Since the outside of the door carries the 3/4-inch plywood paneling to match the house, and that plywood weighs about 2 lbs/sq-ft, I estimate the door weight to be about 7 x 10 x 2 = 140 lbs of paneling with the rest 238 - 140 = 98 lbs the interior panels, hardware, and cobwebs. Knowing this total weight will help later in adjusting the torsion on the springs. After weighing, we removed the scale and blocks, leaving the door fully lowered again. Had I not had a high-capacity freight scale, I might have improvised a crude weighing device from levers and smaller weights of known mass, or a lever arm pressing a reduced proportion of the full weight onto a lower-capacity scale. Another factor to remember is that The weight of a wood door can vary with humidity.
Uncentered center bearing plate: The center bearing plate need not actually be in the center. It doesn't much matter where it is, since the purpose of the bracket is to anchor the spring ends. This anchoring must be secure, since all the torsion is held together at that point. On a stud-framed wall, this bracket may be placed over the stud closest to the center rather than exactly at the center of the door opening.
The Genie SilentMax 750 belt drive garage door opener isn't as feature-packed as the Chamberlain B970, but its value is hard to overlook. The 75-HPc motor isn't as strong as the B970s, but is still plenty strong for any residential use, and the opener is widely judged to be pleasingly quiet. Smart features are built in, too, but using those requires the addition of the optional Genie Aladdin Connect module (Est. $95). The biggest downside is that there's no battery back-up.

Our team of 100-plus technicians and service representatives takes care of you every step along the way. Our technicians are the best in the area. They’ll provide expert guidance as you consider your options, and then top-notch service to complete the repairs. When you want Cincinnati or Northern Kentucky garage door repair you can trust, choose AE Door & Window.
When you’ve measured your door and found a replacement that you love, garage door installation and repair services are only a click or call away. Our vast network of independent Clopay Dealers provide dependable service, and are happy to help with regular maintenance and replacement parts after your door is installed. Replacement garage doors installed by our Master Authorized and Authorized dealers are also eligible for a 1-year installation warranty to ensure your door operates reliably. For a quote or to request local service, visit our convenient dealer locator to find a Clopay Dealer near you!

Torsion springs are devices that lift most of the weight of a garage door so that the door can be opened manually or by an electric opener. The torsion principle is applied via an efficient and economical apparatus consisting of a torsion shaft under spring torsion, which turns lift drums, which wind cables attached to the door near the bottom. All of this apparatus is mounted over the top of the door. The energy stored is sufficient, in an uncontrolled release, to break things, hurt you, or perhaps even kill you. The same could be said of jacking up your car to change a tire, or mowing your lawn, or raising children, so it is not crazy to want to do this yourself.


Overhead Door® openers​ and garage doors are built with longevity in-mind. By performing a few routine tasks, you can help ensure your garage door system stays safe and stands the test of time. One important part of garage door system routine maintenance is to make sure the photo-eyes have not gone out of alignment. The photo-eyes are the infrared sensors which monitor whether the space at the bottom of your garage door is clear. When these sensors are not lined up properly they will keep your door from closing. Make sure to occasionally check your photo-eyes’ alignment to ensure they are correctly detecting obstructions to keep your garage door safe and operating properly.
This opener is easy to install for most DIYers and comes with two remotes and a wireless keypad so you can open the door with a pin. If you are interested in having this smart-enabled you can purchase a separate kit to do so. The Safe-T Beam helps prevent accidents using a infrared beam that will open or close the door if a car is getting to close. 
Before setting the last panel in the tracks, set the power unit on the actual frame and slide it in the ends. Hardened screws are used to attach the center bracket (Image 1). They are a different type screw — they are tougher and will last a lot longer. Make sure the bracket is level (to the eye) when installed and leave the bracket a little loose so adjustments can be made. Fasten down all the hinges (Image 2).
Even if one could somehow stretch and clamp the springs to the proper extra length, the process would still be more trouble, and there would be little or no reduction of risk. Lifting the full weight of the unsprung door by hand and clamping it in the raised position is dangerous in itself, and creates the same amount of stored energy as winding the springs, ready to slip out of your hands. Many doors won't travel far enough up the track to provide clearance to access the springs. You're also going to have to deal with winding stiff steel cables onto both lift drums at once without any resistance to maintain tension. Finally, even if you managed to complete the installation with the door raised, you then have to lower the massive door against an untested balancing torque. If you've made a mistake, then that massive door has nothing but your skeletal force applied through your meat clamps (hands) to prevent it from falling down and crushing whatever is in the way (perhaps your feet?).
Keep in mind that when the springs are released there is nothing to help with weight replacement. Garage doors weigh 150 pounds or more and if the door were not locked in place, there would need to be some way of holding it up until it can be lower manually. If no one is available to help, a clamp can be put on the track at the end of the door (Image 1). When ready, release the clamp and take the weight of the door.

Drive type Garage door openers work in a variety of ways. A chain-drive model raises and lowers doors with a metal chain — these tend to be inexpensive and able to handle heavier doors, but they’re loud. A belt-drive opener uses a belt and operates more smoothly and quietly. Screw-drive openers, which lift doors with a threaded steel rod, are also quiet and don’t require much maintenance. Finally, a direct-drive opener operates as a single unit — the whole contraption moves to lift the door. These tend to be the quietest, smoothest mechanisms available.


The inside of the door panels bear a few dings, since filled with Bondo, from my teenage boys shooting hockey pucks. The streaks on the right that look like dinosaur claw scratches came from operating the door inadvertently when the rear doors of a van were open. The responsibility for these scars is all mine; they have also been Bondo-filled. We tend to use a lot of Bondo around our house. The crud on the walls and ceiling are cobwebs and dust infiltrates.
The "safety issue" trick: Another tip-off is the use of language like "safety issue". This is meant to trump any objections you might have to a costly repair bill. Don't be manipulated by the suggestion that you are risking disaster if you don't buy something expensive. Even if you think the risk is genuine, get another estimate, and tell the second repairman you are skeptical; every technician loves to prove the competition made a mistake.
Garage door manufacturers typically produce garage doors fitted with torsion springs that provide a minimum of 10,000 to 15,000 cycles and are guaranteed for three to seven years. One cycle is a single opening and closing sequence. Most manufacturers offer a 30,000 cycle spring. However, it is important to remember that if the weight of the garage door is increased by adding glass, additional insulation, or even several coats of paint, the life of the torsion spring may be greatly reduced. Additionally, springs at highly humid environments, such as coastal regions tend to have a significantly shorter cycle life, due to the corrosive cracking.
The history of the garage door could date back to 450 BC when chariots were stored in gatehouses, but in the U.S. it arose around the start of the 20th century. As early as 1902, American manufacturers—including Cornell Iron Works—published catalogs featuring a "float over door." Evidence of an upward-lifting garage door can be found in a catalog in 1906.[4]
The not-so-competitive advertising trick: How about this racket: We have all heard how you should get at least three bids for any home improvement jobs, right? In some areas the largest ads in the yellow pages are from a single business using various names and phone numbers, masquerading as independent competitors. When you call asking for prices, "they" all quote you very high numbers. You are tricked into thinking you have shopped around for the prevailing price. (The more modern version of this is multiple Web sites that all direct you to call the same person.) If you've ever had to call a plumber you may have unknowingly been a victim of a similar trick.
We are proud of the work we do in Northwestern North Carolina. We love this community and we love serving it. So whether you think you need a small repair or a major overhaul, we want to be the team that helps you increase the value of your home while making it a safer place to live for you and your family. Our professional and friendly sales team are eager to connect with you, so contact us today and find out just how we can ease your concerns and make transform your garage!
Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.

Keep in mind that when the springs are released there is nothing to help with weight replacement. Garage doors weigh 150 pounds or more and if the door were not locked in place, there would need to be some way of holding it up until it can be lower manually. If no one is available to help, a clamp can be put on the track at the end of the door (Image 1). When ready, release the clamp and take the weight of the door.
As we’ve mentioned before, springs are installed within your garage lift mechanism in order to help lift the door. Because doors are so heavy, the lift motor would undergo far more significant wear and tear if it had to lift the full weight of the door every time you opened it. Furthermore, in order to ensure that you can open your door even if you lose power in your home, springs allow you to lift the door by hand when the motor is disengaged.

Note the left winding cone with red spray paint. This shpritz of paint is applied to create fear and doubt in the mind of the do-it-yourselfer. Sometimes it is a color code for the wire size (using a DASMA standard, red indicating 0.2253 inch diameter wire). Sometimes it indicates the winding direction: red may indicate right-hand winding, but don't rely on that; do you own independent analysis. Sometimes it is a manufacturer's private code for another dimension than wire size. This color code is for the installer's information when the spring is new; I would not depend on interpreting the color code properly on an old spring, since one can't be certain of a correct interpretation without documentation from the original supplier.

Not only was the upward-lifting garage door and the electric garage door opener invented by Overhead Door Corporation’s founder C.G Johnson in the 1920s, but we also have a tradition in excellence for garage door repair, service and maintenance. Even with the most reliable products problems can arise and when they do it’s important to know who to contact to fix these issues while providing solutions to prevent future complications.
Removing winding cones from an old broken spring for reuse in a new spring: Springs without the winding cones installed are a little cheaper than with the cones. Twisting the old cones into a new spring is easy with a vise and pipe wrench, but it can be tricky removing old cones from a broken spring for reuse. To remove old cones, mount the cone in a vise such that the spring portion is free. Grab the last few turns of the spring in a pipe wrench, engaging the teeth of the wrench into the end of the spring wire. Turn the wrench against the end of the spring wire, releasing the end of the spring from its clamping onto the cone, as you twist the loosened spring off the cone. Another more certain if not brutal method is to use an angle grinder with a thin metal-cutting disk to cut through the loops of spring wire where the loops wrap around the cones, being careful not to nick the cone itself too much. You could also cut into the old spring loops with a just hacksaw and break off the loops with hand tools, but this will require a lot of effort.
Absolute Overhead Door recently launched a blog that can be found here so that readers would be able to see the benefits of a garage and what they should do in the event their newly driving teenage drove into the garage door. The blog offers many tips for “fix at home” solutions as well as giving examples of situations when calling us for a service call is the best decision. In our blog, we give professional and honest recommendations for the most reader and budget friendly options for families looking for advice that doesnt cost a fortune and an obligation to purchase a new garage door from a salesman afterwards! Check it out! We hope you enjoy it.
Technician Mark called 1/2 hr before coming. Very knowledgeable and friendly technician. Originally scheduled as a tune-up but after pointing out several potential problems I decided on the complete overhaul package. All parts were on the truck. Technician completed job in a little over an hour. Very satisfied. Definitely would recommend.Bob PNorth Myrtle Beachread more
Carriage: These doors mimic the look of doors found on old carriage houses in the days of horses and buggies. Because of their rustic look, they are often favored in the West and Southwest of the United States. The doors swing open like oversized French doors and hang from jambs on hinges. With their unique look, they create an area of visual interest for your home and are quite energy efficient. The downside is they require a considerable amount of clearance to work properly. Because most carriage garage doors are largely composed of wood, you may need to replace deteriorating or rotting door materials. The average cost for carriage garage door repairs is $133.
Spring rate and torque: In my spring replacement above, the wire size was d = 0.2253 inches, and the ID was 2 inches, giving a mean diameter D = 2.2253 inches. The number of coils is L/d = 24 inches / 0.2253 = 107, less about 5 dead coils on the winding cones, or 102 active coils. Thus the spring rate is K = (π*28.5*10^6 * (0.2253)^4) / (32 * 102 * 2.2253) = 31.8 in-lb/turn (IPPT). Winding 7.5 turns * 31.8 in-lb/turn yields a torque of 238 in-lbs per spring.

Bringing simple convenience to your home the Chamberlain Bringing simple convenience to your home the Chamberlain 1-1/4 HP Garage Door Opener provides instant garage access at your fingertips. Featuring innovative built-in smartphone control and battery backup this system ensures that you're never locked out of your home. Boasting a steel reinforced belt drive the B970 features anti-vibration technology ...  More + Product Details Close
×