End treatments: Torsion springs also are made in a variety of end treatments. The "standard torsion end" is most common, as is pictured in my examples, consisting simply of a short, straight length of wire projecting tangentially. Various non-standard end treatments have longer "ears", U-turns, ends bent in toward the center or along the axis, or even loops. Non-standard ends are used in end fasteners peculiar to various manufacturers, which would seem to serve mostly as a guarantee that you buy overpriced replacements from that one source.

Most styles, whether traditional or contemporary, feature panels, trim, and other detailing. Doors with true frame-and-panel construction tend to be sturdier than those with decorative detail that is merely glued or nailed on. Many styles have glass panels on the top row, which looks inviting from the street and brings daylight inside. You can also find roll-up doors with shatterproof glass or frosted plastic in all the panels, for a more modern look.
The right side of the photo shows the center bearing plate where the stationary cones attach with two bolts. Some doors may have only one spring rather than two equal ones as shown here (indeed, old marks on the shaft show that this door originally had one spring about twice as long on one side). Above the center bearing plate is the bracket and track from the electric opener.
The wire size and winding direction are easily discovered and proved, as I will explain below. You absolutely must know and understand the critical measurements of your old springs to order replacements. This assumes that the old springs were the correct to begin with; it is not uncommon to have incorrectly sized springs on a door due to a previous sloppy installation, or a significant change in weight of the door.
Horsepower is another key factor when it comes to garage door openers. Look into ½ horsepower garage openers if you have standard aluminum doors. Oversized doors and one-piece doors may require 3/4, 1 or 1¼ horsepower garage door openers. Garage openers with higher horsepower use less effort to operate and minimize wear and tear on the motor. This is ideal if your garage doors act as the main entrance to your home.
My garage door broke on a Saturday night as I was getting ready to leave for a holiday party. Kelvin was here within 30 minutes. He reviewed everything with me that was happening with my door. He gave me the estimates of what was immediately needed to be done in order for my door to raise and then what I will need to have done very soon. I could see all the problems he pointed out to me and I decided to have everything done. He completed everything that night. I was very satisfied with Kelvin’s professionalism and the work he did. Thank you again.
With over 300 independently moving parts, your garage door is a deceptively complex piece of equipment. To help prevent malfunctions and break-downs, it is a good idea to occasionally perform a garage door tune-up to keep all of these parts in good working order. A regular tune-up service by a Sears professional can prevent unexpected door problems and prolong the life of your existing equipment.

Another moment of truth arrives as the winding-up of the springs begins. (I am just posing here with the camera held out in my left hand. Except for lifting the door onto the scale, this was a one-man job, including the photography.) The position of the bars in this photo was necessary to take the photo, and does not show a correct winding technique, You should not have to swing the bar up as high over the top as shown. The lower bar during winding should swing from pointing down to pointing a little past horizontal. Then you hold that bar horizontal while socketing the other bar pointing down, apply force to that (now) lower bar, then remove the (now) upper bar, wind one-quarter turn, and repeat.


When it comes to garage doors, Jarusewski’s Overhead Door Service Inc. is your premiere choice. We are true professionals and your satisfaction is key. Let us show you the quality of our garage doors and how you can improve both the look and value of your home or business. From the appearance of the door, right down to strength and durability, we’ve got a door for everyone.
Since 2015, we’ve tested a variety of devices such as smart locks, video doorbells, DIY home security systems, thermostats and more. We use these testing experiences to inform our evaluations of other equipment. As time and resources allow, we occasionally test new types of products, but there are still some circumstances where we’re unable to conduct in-house tests. When testing isn’t possible, we conduct thorough research using the same standards we apply to our in-house tests – this is the case with smart garage door openers. We’ve reviewed garage door openers since 2011. 
I could not be happier with the service from Precision, and Tom, especially. About a year and a half ago I called to have my garage door that was sticking, repaired. Tom came out same day and replaced, adjusted, serviced all moving parts and got it going smoothly. He has since come out within hours of a call to adjust and keep (what might not be the best) door, (originally installed by someone else), operating well. I recommend Precision and Tom with complete confidence.
Though you can do some maintenance to your garage doors on your own, it may be a good idea to schedule routine inspections with a professional. A typical service call will include a manual inspection of the door and opener. Then adjustments can be made including spring tension, chain/belt tension, limits and force adjustments and door lubrication. Fees for this service vary from place to place, but garage door repairs typically cost between $147 and $340.
Modern garage door openers include basic to advanced features that improve safety and deter break-ins. Examples include an automatic stop if a descending door encounters a solid object such as the hood of a car and light beam sensors that detect the presence of an object -- or a person or pet -- and stop a garage door's downward movement before accident or injury can occur. Available security options include remote lockouts for when you will be away from home for an extended amount of time, remote codes that change after each use, and lights that turn on automatically when your garage door opens or if movement is detected inside.

Cable fail-safe redundancy: Based on the proper setting of the drums on the torsion shaft, the two lift cables divide the lifting force equally to keep the door level as it rises. This not only levels the door, but also provides a fail-safe mechanism. If one of the cables should fail, such as from breaking or losing its end attachment, the other cable will then carry the full weight of the door. This will pull the door up on one side with twice the normal force, while the other side falls from its now unsupported weight, tending to make the door bind in its tracks and jam. Although not foolproof, this is a safety feature of the design which keeps the door from falling catastrophically if a cable were to fail while the door was traveling. The jammed condition also prevents a lowered door from opening with the hazard of a single broken cable, further minimizing the chances of both cables failing. Since if one cable fails the other must sustain the full weight of the door, the cables and attachments are rated many times the normal working load of half the door weight. A proper safety inspection of the door should include a critical look at the cables and their attachments.
With hundreds of moving parts that are all required to work together, it's no surprise that garage doors may need occasional repair and maintenance. Garage door repair services are also required in emergency situations, like when the garage door won't operate and the car is trapped inside or you've accidentally backed into the door when it was closed. Whether it's a specific repair of your garage door opener, a broken spring that needs to be replaced, or a bent or rusted track, The Home Depot's local, licensed service providers can get the job done quickly and efficiently.
Containment cables. When old extension springs break, the springs and cables become heavy whips that damage cars and even injure people. To solve the whipping problem, manufacturers now offer containment cables that run through the center of side-mounted extension springs. If you have extension springs and don’t plan to replace your door, make sure the springs have these containment cables, or have a professional install them.
Are you needing garage door repair? Has your garage door opener stopped working, or are you looking to boost your curb appeal? Whatever your garage door need may be, your local authorized Overhead Door™ Distributor is there to assist. You can find the nearest Overhead Door™ Distributor near you today by using our Distributor Locator​ to search your area. ​​
An extension spring counterbalance system consists of a pair of stretched springs running parallel to the horizontal tracks. The springs lift the door through a system of pulleys and counterbalance cables running from the bottom corner brackets through the pulleys. When the door is raised, the springs contract, thus lifting the door as the tension is released. Typically these springs are made of 11 gauge galvanized steel, and the lengths of these springs are based on the height of the garage door in question. Their lifting weight capacity can best be identified by the color that is painted on the ends of the springs.
Spring rate and torque: In my spring replacement above, the wire size was d = 0.2253 inches, and the ID was 2 inches, giving a mean diameter D = 2.2253 inches. The number of coils is L/d = 24 inches / 0.2253 = 107, less about 5 dead coils on the winding cones, or 102 active coils. Thus the spring rate is K = (π*28.5*10^6 * (0.2253)^4) / (32 * 102 * 2.2253) = 31.8 in-lb/turn (IPPT). Winding 7.5 turns * 31.8 in-lb/turn yields a torque of 238 in-lbs per spring.

Spending your whole weekend setting up a new garage door opener is not on the top of most peoples list. This opener is easy to install for most levels of DIYers and it provides a quiet and reliable open and close. This has 3/4 HPc DC chain features and the powerhead can open 12" in a second. It has a wireless remote and Intellicode 2 security to prevent people from breaking into your home. 
Door repair business advice (warning to consumers, you are not allowed to know this): Thinner wire is excellent for shortening spring lifetimes, lightening your inventory on a service truck, and getting paid for frequent service calls. This is why your industry chooses to set "standard" springs to have thin wire and despicably short lifetimes. If you want to maximize profits and fleece your customers, install springs that predictably break in about 7 years on a door that should last decades, even though it is just as easy for you to install slightly more expensive springs that should last the life of the door. Remember that the customer wanted the cheapest price, so you need not feel any guilt about this low-balling.
The typical electric garage door opener consists of a power unit that contains the electric motor. The power unit attaches to a track. A trolley connected to an arm that attaches to the top of the garage door slides back and forth on the track, thus opening and closing the garage door. The trolley is pulled along the track by a chain, belt, or screw that turns when the motor is operated. A quick-release mechanism is attached to the trolley to allow the garage door to be disconnected from the opener for manual operation during a power failure or in case of emergency. Limit switches on the power unit control the distance the garage door opens and closes once the motor receives a signal from the remote control or wall push button to operate the door.[3]
Correct spring size is determined by factors such as the weight and height of the door. You cannot substitute a different spring and just tighten or loosen the winding to make it balance the load. Why? To maintain cable tension under all operating conditions, the spring must retain about one turn of unspent wind-up at the top-of-travel position, which with the lift drum size and door height predetermines the number of turns of winding at the bottom-of-travel; and furthermore the torsion of the fully-wound spring at the bottom-of-travel must be slightly less than that needed to lift the weight of the door when translated by the lift drums.
Tools in Action says the Ryobi Ultra Quiet has plenty of versatility, as you can plug devices into the opener hardware, like a Bluetooth speaker, a fan, or even an 18V Ryobi cordless tool battery. When the opener has power, it will charge the battery. But if your home ever loses power, the 18V battery works as a backup to the garage door opener, allowing it to operate normally.
And for some extra features, you'll appreciate accessing the system through the MyQ smartphone app. You can set up this Chamberlain opener to automatically close the door after 1, 5, or 10 minutes, which is great for people who are a bit forgetful. We also really like the motion-detecting control panel, which turns on lights whenever it records nearby movement.
Follow the manufacturer’s instructions to assemble the opener and mount the rail to the header bracket above the door. Then set the opener on a ladder where you’re going to install it. The ladder (usually an 8-footer) holds the opener in position while you measure for your lengths of angle iron. If necessary, put boards under the opener to raise it.
Wheel Track Obstruction – Try closing the garage door manually to see if there are obstructions on the wheel tracks. If that is not the case, examine your tracks for potential damage like dents and bends. Look at your door to see if it is hanging unevenly. If the track is damaged or the door is hanging unevenly, it is time to call a professional for repairs. Track repairs can typically cost $133 to $154. Cost for correcting the uneven hanging of doors themselves can vary greatly, but typically cost about $125.
As noted above, set-screw clamping may have distorted the cross-section of the shaft and made it difficult to slide off all the hardware. With the shaft on the floor, it may be possible to restore enough roundness to proceed, using compensating clamping force to the distorted area via a machinist's vise, an arbor press, a hydraulic shop press, etc., on the shaft body. Burrs and other slight distortions on the shaft can be filed off with a hand file or touched with an abrasive wheel on an angle grinder. At some point, the condition of the shaft may just be degraded enough that it ought to be replaced.
When I called to schedule the repair service, I was transferrd 5 times and spoke with 6 service reps. Each rep was very confused by my request to get my garage door repaired. One rep actually told me that Sears doesn't repair garage doors. I had to tell her that Sears installed the door. When I finally found a rep who could schedule my service, it took one week for the appointment.
A rolling code is a protocol used by garage door openers to keep your door safe and secure. When the radio signals from your remote control are broadcast to your garage door opener, it uses a specific code to communicate. Older models used the same code every time, making garage door openers vulnerable to burglars using a radio frequency identifier device. 

The two set-screws in the winding cones have a 3/8-inch square head, which fits a 3/8-inch open-end wrench or 8-point socket, or a 7/16-inch 12-point socket or 12-point closed-end wrench. I carried an extra wrench in my pocket while winding, since I didn't want to be holding a wound spring that I couldn't set because I had dropped the wrench (although one could rest the winding rod against the door in this case while picking up a dropped tool).
You might be thinking: Aha! Why don't we lift the door, clamp it in place, and install the springs while they are thus safely unwound, rather than deal with all that accumulation of hazardous torque? The answer: At the top-of-travel, the unwound springs are not fully relaxed; they are still clamped to the torsion shaft with a significant stretch along the shaft axis, plus about a half-turn to keep the door snug at the top. This extra length amounts to the stacking of extra turns that accumulate from winding, also termed "spring growth" in the business. In my case this is about 7 turns of 0.2253 wire, or about 2 inches. Stretching the spring that much and clamping it with a half-turn or so of twist is not feasible.
Another moment of truth arrives as the winding-up of the springs begins. (I am just posing here with the camera held out in my left hand. Except for lifting the door onto the scale, this was a one-man job, including the photography.) The position of the bars in this photo was necessary to take the photo, and does not show a correct winding technique, You should not have to swing the bar up as high over the top as shown. The lower bar during winding should swing from pointing down to pointing a little past horizontal. Then you hold that bar horizontal while socketing the other bar pointing down, apply force to that (now) lower bar, then remove the (now) upper bar, wind one-quarter turn, and repeat.
When garage door repair isn’t an option — perhaps the current door is beyond fixing or you want to upgrade to a quieter, more energy-efficient model — it’s time to buy a new one. But choosing a garage door is not as simple as it sounds, even when you know the right size for your home. A wide range of materials, styles and finishes are available, and each factor influences the cost. Garage doors are made of aluminum, steel, vinyl, fiberglass, masonite, wood (typically cedar or mahogany), or a composite of several materials. They may be insulated against cold or heat. Traditional and modern styles include raised panel, carriage house or crossbuck. Most styles have window or arch options, and are available in different wood finishes and neutral colors. Because garage doors account for a large part of a home’s exterior, their appearance is usually a homeowner’s top priority. An attractive garage door can increase a home’s curb appeal and resale value.
Because your garage door can be customized, pricing varies. Our Clopay configurator will help you review pricing as you begin your project. You’ll start with your door size and whether you need a single or double car door. Next, you can choose the collection of door, which gives you options of various materials and styles. Then, you’ll choose your construction, which allows you to decide what you need in terms of energy efficiency, durability and noise control. Lastly, you will be able to visualize the design and see an end price. Other optional add-ons include windows, decorative hardware, smart features and the r-value. However, you do not have to use the configurator. We also install standard garage doors that have not been customized so you know the product price early on in the process.

First and foremost, a garage door, by design, contains springs designed to balance your door and make it easier to lift. Those springs are under incredible amounts of tension. If a spring breaks or is improperly released, it can cause incredible and potentially fatal injuries. Keep in mind, when working on a garage door spring, it is likely that your face and head will be close to it, meaning that your most sensitive area will be in the direct path of the released spring.

Garage Door Service Co

×