These springs weighed in at just over 9 pounds each, including the winding cones. They are covered with a light film of oil, and at this point the job starts to get messy. The manufacturer has painted them with a "225B24" part number, which no doubt indicates the 0.2253 inch wire size, 24 inches long. Perhaps the "B" indicates the 2-inch inside diameter. Both the left- and right-hand springs have this same number on them.
In the photo, you can see an extra lag screw on the bottom of the plate, reinforcing weak anchoring from the original two screws (hidden behind the springs). This extra screw was applied by a professional garage door technician on a previous repair visit. I have since replaced the backing with a sound plywood panel anchored into the concrete door header. Since these bolts clamp all the opposing torsion to the wall, the attachment must be sturdy.
The right side of the photo shows the center bearing plate where the stationary cones attach with two bolts. Some doors may have only one spring rather than two equal ones as shown here (indeed, old marks on the shaft show that this door originally had one spring about twice as long on one side). Above the center bearing plate is the bracket and track from the electric opener.
But the insulation won’t save energy unless you heat the garage or treat your attached garage as part of the “conditioned” part of your house. The federal Energy Star program recommends against doing this if you park cars, store lawn chemicals, or use solvents there because it could let dangerous fumes inside; it’s better to insulate only the shared wall and use that as the indoor-outdoor boundary.
Unmatched or mismatched spring pair: You may find that you have a pair of springs that are different sizes. This mismatch may be a normal application, since the total torque on the torsion shaft is simply the sum of the torque contribution of each spring (indeed, very large doors can be lifted with 4 or more springs along the torsion shaft). The sum of the torque rates determine the lift; and dividing the torque among multiple springs does not change this. Some repair shops even apply mismatched pairs deliberately, since a few stock sizes of springs can be combined to fit a wider range of door weights than only matched pairs. For example, a technician may carry springs in increments of 20 lbs of lift, and when using pairs this allows a 20 lb increment in possible choices instead of 40 lb increments. Or, one spring from a pair may have broken and been replaced with a spring of equal torque rate but different size than the original.
Horsepower is another key factor when it comes to garage door openers. Look into ½ horsepower garage openers if you have standard aluminum doors. Oversized doors and one-piece doors may require 3/4, 1 or 1¼ horsepower garage door openers. Garage openers with higher horsepower use less effort to operate and minimize wear and tear on the motor. This is ideal if your garage doors act as the main entrance to your home.
Our knowledgeable, dependable and friendly team of professionals can work closely with you to select, design and install a quality garage door that best serves your daily needs, enhances the architecture of your home and fits your budget. The extensively trained and experienced technicians at Kitsap Garage Door can help you with any of your garage door service needs, large or small, and are ready to repair any garage door make or model.
Carriage: These doors mimic the look of doors found on old carriage houses in the days of horses and buggies. Because of their rustic look, they are often favored in the West and Southwest of the United States. The doors swing open like oversized French doors and hang from jambs on hinges. With their unique look, they create an area of visual interest for your home and are quite energy efficient. The downside is they require a considerable amount of clearance to work properly. Because most carriage garage doors are largely composed of wood, you may need to replace deteriorating or rotting door materials. The average cost for carriage garage door repairs is $133.
The Certified Technician, Rey Lopez, was competent, professional, polite, and willing to work. He quickly removed the old door and installed the new one. He then explained the vast differences between what we originally had and what we'd just purchased (stronger spring/tension rates; increased viability of door opening/closing life; beefier hardware; plastic vs. nylon rollers; stronger door reinforcement). Ray performed with alacrity his tasks and then demonstrated the quiet, solid way the door retracted--no banging after the initial rise from the ground. Finally, his attention to detail was so precise that he enabled another remote controlling all three doors, plus he capped some frayed wires, thus solving the problem of why the door opened intermittently. I would rate him a "6" on a scale of "1-5", meaning he went above and beyond our expectations. His "can do" attitude, coupled with the deference he showed, will take him a long, long way. May HaShem richly bless him in his endeavors!read more
Luckily, your garage door is a pretty sound investment. According to Garage Wow Now, garage doors were ranked in the top three for home improvements whose costs are recouped through increased home value. Similarly, realtors regularly increased the list price of a home with a new garage door by 1 to 4 percent! That means, if you spend $2000 on a new garage door, you can increase the value of your home by almost $8000 if you have a $200,000 home. Furthermore, compared with the other two highest rated improvements — siding replacement and deck installation — a garage door replacement is far more affordable.
Repair of garage doors is a licensed trade in many jurisdictions, and manipulation of the market inevitably follows. Look in your phone book yellow-pages under "garage doors" and you'll find a lot of big, costly ads for door service. The profits are quite juicy, I'm sure. The customers need service urgently, and this need will typically arrive suddenly and at a busy time when shopping for prices is not convenient. A few dollars in parts, an hour of labor and travel, and a $150 invoice (assuming the outfit is charging fairly, some are not). Lately (2006) I hear of outfits charging $200 or $300 for this work, and occasionally a story of a $500 or $800 service call. You'll also find the phonebook advertisers waiting eagerly for your call, because artificially high prices inevitably lead to an oversupply of service firms working under capacity.

I backed into my garage door, then my husband tried his hand at fixing it...which only made it worse. The door wouldn't go down and we were leaving town the next day. I called at 9 am on a aturday morning, and Tom called to say he'd be there between 9:45 and 10! He got there just before 10 am and fixed the door in less than 30 minutes. He was very fast, efficient, and knowledgeable. The price was lots lower than I thought it would be. All in all, we were very pleased with the service.
Most garage door openers include a remote that lets you open and close the door from the comfort and safety of your car. Some garage door openers support Internet connectivity, either as an add-on or built in. This allows you to use an app that lets you open or close the garage door from your smartphone or tablet, and monitor your garage door's status (open or closed) from anywhere that you can connect to the net.
While many sites may encourage you to save on garage door replacement costs by installing the door yourself, this is severely discouraged due to safety concerns and the installation techniques and tools required to properly and efficiently replace a garage door. When installing a new garage door, the range of prices also includes the labor performed by the professional garage door technician. These costs can include:
Together with our alliances, we proudly serve all of Australia, including Adelaide, Brisbane, Gold Coast, Melbourne, Perth and Sydney, with top quality sectional garage doors, roller doors, steel garage doors, remote garage doors, tilt garage doors, timber garage doors as well as commercial garage doors, commercial shutters and industrial shutters. If you need custom garage doors, we’re the ones you need to call.  Our manufacturers have been selected for their capacity to meet and exceed our requirements for superior craftsmanship, reliability and a single-minded focus on excellence in customer service.

Garage doors provide one of the major entryways into your home. Therefore, it is essential to ensure that they are secure and in good working order. If you are having problems with your current door, then you need to have a professional determine if it can be repaired or if it will need to be replaced. Here are some of the most common factors that will affect the cost of a garage door repair.
However, in addition to potentially causing injuries to the under-prepared DIYer, a malfunctioning door can become a safety hazard to you and your family. Keep in mind, according to the National Electronic Injury Surveillance System (NEISS), over 13000 people checked into hospitals with garage related injuries in the United States in 2007. You don’t want to turn a loved one into a statistic just to save a few dollars!
Before setting the last panel in the tracks, set the power unit on the actual frame and slide it in the ends. Hardened screws are used to attach the center bracket (Image 1). They are a different type screw — they are tougher and will last a lot longer. Make sure the bracket is level (to the eye) when installed and leave the bracket a little loose so adjustments can be made. Fasten down all the hinges (Image 2).
If your door feels heavy, it is likely that your springs have started to wear down and are no longer capable of bearing the weight that they once did. Now, don’t worry, just because a spring is starting to lose its strength doesn’t mean it will snap at any moment. However, simultaneously, a weak spring isn’t any safer to try and repair on your own.

Yet another professional wrote me to say that the red paint on certain components of these assemblies is an "industry standard" that signals, "Danger! Part under hazardous tension." Other items under tension like the bolts on the cable attachment plate on the door should therefore also be painted red. If so, then this is a new, ambiguous, unreliable, and little-publicized standard, because none of my old hardware shows it, red paint also means other things, and searching the Web does not readily turn up references to this practice.


If the wires that run from your opener to the photo eyes and to the wall button are exposed, replace them, too. Those wires have probably been in your garage for 10 years or more, and they may be nicked or worn. Newer openers are extremely sensitive and won’t work if a wire is damaged. It only takes about 15 minutes to run the new wire, so it’s time well spent. If the wires are protected inside the wall, you don’t need to run new wire.
Looking to repair your garage door opener? Common problems could range from issues with the remote or wall switch that control the garage door opener to more serious issues like a grinding noise coming from the opener itself. If you need help with repairing your garage opener, schedule a repair appointment today! We repair all major brands and have same-day availability in most markets, so we can get your garage door opener repaired and running smoothly.
Stress and lifetime: Calculating the maximal stress in the wire is useful for estimating the lifetime. Using the formula above, the bending stress S in the spring wire is 32*238/(π*0.2253^3) = 212 Kpsi. The spring index C is D/d = 2.23 / 0.225 = 9.88. The Wahl correction factor is Kw = (4C-1)/(4C-4) + 0.615/C = 1.15. The Wahl-corrected stress is Kw * S = 1.15 * 212 Kpsi = 244 Kpsi. This predicts about a 10,000-cycle lifetime, which is the standard "cheap spring" configuration originally installed. Note that while this stress is proportional to the torque being applied, it is also in proportion to the inverse third-power of the wire size. Thus slightly heavier wire sizes (and suitably adjusted D and/or L) radically improve the expected cycle lifetime of the spring.
Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.

Disclosure: This post is brought to you by the Insider Picks team. We highlight products and services you might find interesting. If you buy them, we get a small share of the revenue from the sale from our commerce partners. We frequently receive products free of charge from manufacturers to test. This does not drive our decision as to whether or not a product is featured or recommended. We operate independently from our advertising sales team. We welcome your feedback. Email us at [email protected]
 We were very pleased with the service we received. The receptionist that took our information over the phone was courteous and efficient. The young man, Nate, who came to the house was on time, respectful of our wants and needs, and very knowledgeable about the job. He was able to fix our door easily. Finally we have a garage door that works with a push of the button! We highly recommend this company for your garage door needs.read more 

Since 2015, we’ve tested a variety of devices such as smart locks, video doorbells, DIY home security systems, thermostats and more. We use these testing experiences to inform our evaluations of other equipment. As time and resources allow, we occasionally test new types of products, but there are still some circumstances where we’re unable to conduct in-house tests. When testing isn’t possible, we conduct thorough research using the same standards we apply to our in-house tests – this is the case with smart garage door openers. We’ve reviewed garage door openers since 2011. 
Drive type Garage door openers work in a variety of ways. A chain-drive model raises and lowers doors with a metal chain — these tend to be inexpensive and able to handle heavier doors, but they’re loud. A belt-drive opener uses a belt and operates more smoothly and quietly. Screw-drive openers, which lift doors with a threaded steel rod, are also quiet and don’t require much maintenance. Finally, a direct-drive opener operates as a single unit — the whole contraption moves to lift the door. These tend to be the quietest, smoothest mechanisms available.
Our value pick is the Chamberlain PD76EV. It costs about $50 less than our top pick, but it has most of the higher-priced model’s advantages. The PD76EV has the same lift capacity, horsepower, lift system and automation compatibility. However, it doesn’t come with advanced features such as a backup power source, close timer and keyless entry pad. If you can live without those, this opener is a great choice.
Insulation, which increases energy efficiency and can help to lower utility bills, is crucial when a garage door is attached to the home. In this case, doors with high R-values are preferred. This means it has insulation that can keep the heat in. The higher the R-value, the better insulated your garage will be against outside noise and cold and hot air.
As we’ve mentioned before, springs are installed within your garage lift mechanism in order to help lift the door. Because doors are so heavy, the lift motor would undergo far more significant wear and tear if it had to lift the full weight of the door every time you opened it. Furthermore, in order to ensure that you can open your door even if you lose power in your home, springs allow you to lift the door by hand when the motor is disengaged.

It's a great idea to hire a professional to do your garage door opener installation for a few reasons. First of all, a pro can often be the most time-efficient way to handle the garage door opener installation, because a pro will have the right tools and experience to make your garage door opener installation as swift and smooth as possible. Secondly, a pro garage door opener installation will include making sure all the required garage door opener mounts and sensors are put together properly. A great garage door opener installation will include using the manufacturer’s recommended method of assembly and optimal placement of the garage door opener mount and sensors. Find top-notch garage door opener installation pros on Amazon Home Services and you'll see professional garage door opener installation services at competitive prices. Secure convenience and peace of mind by getting a professional garage door opener installation for your home. You'll never regret adding a garage door opener installation project to your to-do list. If you’re the kind of person who doesn’t have the time or patience to do your garage door opener installation, don’t worry. Because you don’t have to if you don’t want to. Amazon Home Services has you covered, to do your garage door opener installation quickly and professionally. Just schedule the garage door opener installation pro of your choice from our list of top-rated service providers.
Critical measurements: Torsion springs come a variety of standardized sizes, so you have to carefully measure the old springs to know what to order for proper replacements. Tables of standard sizes and designs are on the Web, such as here [www.industrialspring.com]. The four critical measurements (all in inches) are: (1) the wire thickness (which I'm measuring here with a dial caliper; you can also measure the length of a number of closely stacked turns with a ruler and divide by the number of turns in the stack, measuring 10 turns this way makes the math easy), (2) the inside diameter (not outside!) of the relaxed (not wound!) coil, (3) the overall length of the relaxed (not wound!) spring coils, not including the winding cones, and (4) the right- or left-hand winding of the spring. One must glibly quote those figures to the spring supplier, otherwise one's lack of expertise will be obvious, and one will not be worthy of buying the parts.
Screw - Screw-driven lift systems attach a long screw to the motor to move the garage door. These systems are powerful, fast, relatively quiet and require less maintenance than typical chain- or belt-driven systems. Genie and Overhead Door are two popular brands that make screw-driven systems. Based on our research of Genie’s line, you can expect to pay $244 on average for a screw-driven garage door opener.
Reduce your monthly energy bill with insulated garage doors. They feature an insulated core made of polystyrene that’s surrounded by a steel cover. This can help you maintain the temperature inside your home no matter if it’s extremely hot or cold outdoors. Insulated garage doors are also known for their quiet operation. Be sure to look at the insulation rating – or R-value – when considering garage doors. The higher the R-value, the better the insulation.
Remember, not all garage door springs are alike. They are not one size fits all. If yours breaks, make a note of the brand and color code on the spring you need to replace. We'll get you the garage door opener parts you need, from seal kits to torsion and extension spring kits. Save money by replacing garage door hardware instead of replacing the whole unit.
×