Spring stretch: When the door is at the top of travel, the spring(s) are hardly wound, but are stretched, so on a single-spring installation this stretch tends to pull the shaft towards the non-spring side. With two springs, the stretch tends to cancel out. This top-of-travel spring stretch, being about 7 or 8 turns of the wire, will thus amount to upwards of about 2 inches on a typical size spring of 0.253 wire. This spreads out to a gap of about 0.020" per coil on a typical 100-coil spring, so the stretch is not very visible.
If your door has two springs, most professionals and research online says that replacing both springs is the best option. Most torsion springs are rated for 10,000 close/open cycles. If only one of your springs is broken, both springs are still recommended to be replaced. Considering that your second spring will break soon anyways, this added on fix is only going to cost you about $50 extra to assure that you don't have to pay another service fee for a second visit.

Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.


Extremely straightforward and efficient estimating and installation process. We purchased a Clopay sectional steel garage door for our double garage that works flawlessly with our existing door operator. The guys suggested an insulated door, but I thanked them and said no because I don't care for the garage to warm up in the winter and create a corrosive atmosphere of melting snow and salt. Great job!
My door opener disengaged from the garage door. I made a call in late morning and was given an appointment for late the same afternoon. I received a call in early afternoon asking if I would like an earlier service call. Upon arriving the repair man introduced himself and explained that he would need a few minutes to assess the problem and perform an inspection. When he finished he provided me with a through explanation of the problem, the corrective measures he would take and some suggestions to improve operation. We discussed some options, agreed on the cost and the work was complete within a reasonable time frame. The door operates quieter and with less strain than it ever has. Pleasant, friendly, on-time and reasonably priced. Problem solved. It doesn't get any better than that.
Critical measurements: Torsion springs come a variety of standardized sizes, so you have to carefully measure the old springs to know what to order for proper replacements. Tables of standard sizes and designs are on the Web, such as here [www.industrialspring.com]. The four critical measurements (all in inches) are: (1) the wire thickness (which I'm measuring here with a dial caliper; you can also measure the length of a number of closely stacked turns with a ruler and divide by the number of turns in the stack, measuring 10 turns this way makes the math easy), (2) the inside diameter (not outside!) of the relaxed (not wound!) coil, (3) the overall length of the relaxed (not wound!) spring coils, not including the winding cones, and (4) the right- or left-hand winding of the spring. One must glibly quote those figures to the spring supplier, otherwise one's lack of expertise will be obvious, and one will not be worthy of buying the parts.
Garage door springs come in two styles: torsion (see above), which mounts on the header above the door, and extension (Photo 1), which floats above the upper roller track. In the past, extension springs were safer to install but didn’t have containment cables running through the center of the spring. Without cable, these springs become dangerous, heavy whips when they break. They also tend to be noisier than torsion springs, and we recommend you use them only if you don’t have the 12 in. of headroom above the door that a torsion spring requires.
Wood garage door: There’s no substitute for the distinctive look of wood. It’s typically made of moisture-resistant cedar, redwood or cypress and offers the most flexibility for custom designs. Depending on climate and exposure, wood doors require more maintenance. The average cost for a 16-by-7 double door made of quality wood: $1,200 to more than $4,000.

Your garage door is used often, generally more than any other door on your home. Therefore, it’s important to make sure that it’s tough, dependable and weather resistant. Our doors are fully capable of meeting all these requirements and are specifically designed with our customers in mind. While durability is important, so is appearance and we offer many different styles and colors of garage doors to match your home or business.

The third stage of garage door opener technology uses a frequency spectrum range between 300-400 MHz and rolling code (code hopping) technology to defeat code grabbers. In addition to transmitting a unique identifier for the remote control, a sequence number and an encrypted message are also sent. Although an intruder could still capture the code used to open a garage door, the sequence number immediately expires, so retransmitting the code later would not open the garage door. The encryption makes it extremely difficult for an intruder to forge a message with the next sequence number that would open the door. Some rolling code systems are more involved than others. Because there is a high probability that someone will push the remote's button while not in range and thus advance the sequence number, the receiver does not insist the sequence number increase by exactly one; it will accept a sequence number that falls within a narrow window or two successive sequence numbers in a much wider window. Rolling code technology is also used on car remote controls and with some internet protocols for secure sites.
Leveling the door: Before commencing the spring winding, to check that you have the door properly leveled on the cables, considering all the factors above that make this a tricky adjustment, apply the winding cone setscrew lightly to lock the (unwound) spring cone temporarily on the torsion shaft, and momentarily lift the door slightly off the floor. Adjust the drum set as needed to level the door, repeating this slight lift test. Loosen the cone setscrew before winding the spring(s).
Today's garage doors come with those door sensors, and if anything is in the path of the door the sensor detects it and raises the door back to the open position. These precautions are important for families with young children or pets. Even if you don't have a mini me or furry friend running around your yard, it's a good idea to have a garage door that is safe for you, your guests and your belongings. 
We only hire and train very experienced technicians, so you can be confident that you will get the best garage door service available. We strive for 100% customer satisfaction on all our work and stand behind our garage door service if you have any issue whatsoever. Our reviews tell of our dedication to excellence and offering the ABSOLUTE best quality products and customer experience. You can check out what our customers have to say about their experience to the Better Business Bureau by clicking here! We guarantee to be the overall top choice in the market for all your garage door needs. We are a family owned garage door company from the Central Kentucky area and only hire technicians that put forth the same honest values that we have. We strive for 100% customer satisfaction and if for any reason that you are unhappy with a technician or their service, we will be happy to make the experience right as we pride ourselves and our company on the highest of customer satisfaction and experience while offering the lowest prices in the market. We are top rated with all service rating and reviewing companies such as BBB, Home Advisor, Demandforce, and Angie’s List. We take our customers experince serious and we guarantee it!
Before setting the last panel in the tracks, set the power unit on the actual frame and slide it in the ends. Hardened screws are used to attach the center bracket (Image 1). They are a different type screw — they are tougher and will last a lot longer. Make sure the bracket is level (to the eye) when installed and leave the bracket a little loose so adjustments can be made. Fasten down all the hinges (Image 2).
Your ad had no cheap coupons or promises.. Just business. Service was more than prompt. No attempt to fix something that was not broke or did not try to sell me anything I did not need. He stated the price at the beginning and stuck to it. (I was so pleased, I did not bother to mention a senior discount.) Very, very pleased that I have found someone I can trust and rely on. GaryRichard 

Garage Door Service

×