Though you can do some maintenance to your garage doors on your own, it may be a good idea to schedule routine inspections with a professional. A typical service call will include a manual inspection of the door and opener. Then adjustments can be made including spring tension, chain/belt tension, limits and force adjustments and door lubrication. Fees for this service vary from place to place, but garage door repairs typically cost between $147 and $340.
Sears garage repair technicians are fast, with same-day, emergency repairs available in most areas. We can replace garage door broken springs, rollers, cables, hinges, sensors and weather seals. We can also adjust garage door tracks and springs to make sure your door operates smoothly. Having problems with your garage door opener? We can repair or replace that too. Check out our line of Craftsman Garage Door Openers. Craftsman is America’s #1 brand of garage door openers! 1

Garage Door Service Company


Next, the torsion shaft is reassembled with the new springs, the drums repositioned loosely on the shaft, this whole assembly slid back into the end bearings, and the drum set-screws tightened down. I tightened the set-screws about 1/2 or 3/4 of a turn after contact with the shaft, which provides a good grip, but does not distort the shaft. The drums can be set on their old positions, if they were correctly installed, which is snug up against the end bearings to remove any longitudinal play in the torsion shaft. Now the lift cable can be reattached to the drums, and a slight temporary torque applied to the shaft to keep the cable taut while the first spring is wound. This temporary torque is conveniently applied with a pair of locking pliers clamped on the shaft, positioned such that they hold the torque by pressing lightly against the wall above the door, before you start the spring winding, The locking pliers stay on the torsion shaft until you have finished the spring winding locked down the spring cone(s) with the setscrew(s), and removed the winding bars. Then you simply remove them with the release on the wrench handle. I feel that any job that doesn't require a trick manipulation with either locking pliers or duct tape (or in the ultimate case, both!) is just too boring. My trusty pliers look a trifle rusty ever since I used them to clamp something on my outdoor TV antenna "temporarily" and left them out in the weather for, oh, several years. The white stuff on the drum is paint overspray from the original painting of the garage interior.
Technician Mark called 1/2 hr before coming. Very knowledgeable and friendly technician. Originally scheduled as a tune-up but after pointing out several potential problems I decided on the complete overhaul package. All parts were on the truck. Technician completed job in a little over an hour. Very satisfied. Definitely would recommend.Bob PNorth Myrtle Beachread more
Measurements: With the door in the down position, I measure a wire size of 0.273 inches, outside diameter of 2.0 inches, and overall length of 41.5 inches. Relaxing the spring shortens the length by about 7.5 coils of wire, so to estimate the relaxed length, we deduct the wire diamter of 0.273 inches times 7.5 from the 41.5 inch wound length, yielding an estimated relaxed length of 39.5 inches. The mean coil diameter is 2.0 - 0.273, or 1.73 inches. Perhaps this was actually a 40-inch-long spring with a 1.5 ID, 1.75 mean diameter, and 2.0 OD, but let's continue on calculating with the actually observed sizes. The number of coils in the relaxed spring is the relaxed length of 39.5 inches divided by the wire size of 0.273 inches, or about 145 coils. Deducting about 5 dead coils at the ends yields 140 active coils.
In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the project yourself, but you should recruit help for removing the old door.
The majority of those who have purchased this product have been happy with it, saying it’s extremely quiet and comes with a great lifetime warranty. Some of the more critical reviews had to do with the remote not working well and other minor malfunctions. (A few quick tips can help you fix any common garage door opener problems.) However, most were satisfied with the product and would recommend it to others. 

Angle iron provides a stronger installation and reduces vibration, which helps extend the opener’s life span. In an unfinished garage, attach the angle iron directly to the face of a joist with 1-in. lag screws. For finished ceilings, attach angle iron along the bottom of a joist with 3-in. lag screws. Hang the opener using two more lengths of angle iron and nuts and bolts. Use lock washers or thread-locking adhesive to keep vibration from loosening the nuts.


Door repair business advice (warning to consumers, you are not allowed to know this): Thinner wire is excellent for shortening spring lifetimes, lightening your inventory on a service truck, and getting paid for frequent service calls. This is why your industry chooses to set "standard" springs to have thin wire and despicably short lifetimes. If you want to maximize profits and fleece your customers, install springs that predictably break in about 7 years on a door that should last decades, even though it is just as easy for you to install slightly more expensive springs that should last the life of the door. Remember that the customer wanted the cheapest price, so you need not feel any guilt about this low-balling.
Make sure the door is balanced. Close the door and pull the emergency release cord (always close the door first so it can’t come crashing down!). Lift the door about halfway up and let go. The door shouldn’t move. If it slides up or down, the torsion spring needs to be adjusted (or maybe even replaced). Adjusting the torsion spring is dangerous, so don’t attempt it yourself (you could get seriously hurt). Call a pro to adjust it.

Your ad had no cheap coupons or promises.. Just business. Service was more than prompt. No attempt to fix something that was not broke or did not try to sell me anything I did not need. He stated the price at the beginning and stuck to it. (I was so pleased, I did not bother to mention a senior discount.) Very, very pleased that I have found someone I can trust and rely on. GaryRichard 

Garage Door Service

×