You must use springs that are matched to the weight of the door. You cannot compensate for the wrong size spring by adjusting the number of winding turns. If you do not know a proper spring size, then you or your spring supplier must calculate a proper size (see below) based on an accurate weight (within 5 pounds) of the door. So you must then in turn have an accurate weight.
The "liability" angle: The flip side of "safety issue" is "liability". This is not used to directly sell you something; it is used to demean the cheaper alternative and prod you into buying a more expensive (and profitable) option. For example, you may be pressured into buying a whole new door, when you just need a new spring, by the salesman telling you he can't just replace the spring due to "liability" issues. Since product liability is a big burden on the garage door industry, and so many old doors (and especially automatic openers) are dangerous, this may be a genuine reason to accept a higher price.

We would definitely recommend Precision to anyone that needs garage door services! We were able to get a service appointment right away! Tom arrived and was very professional and courteous. He took the time to go over what repairs were needed and provided an estimate. He was ready to do the repairs right then and there and within a few hours, we had our garage door up and running like new! Thanks to Tom and Precision for a positive experience!
In my case, removing and replacing the relaxed springs required that I take down the assembly: torsion shaft, lift drums, and bearings. Doing that requires unbolting the center bearing plate from the wall, removing the drums from the shaft, and finally sliding the shaft back and forth out of the end bearings to remove the whole assembly off the wall. I am fortunate to have a lot of clearance in this garage to make the disassembly simpler. Tighter clearance to walls or ceiling would make disassembly a more difficult manipulation.

Garage door springs come in two styles: torsion (see above), which mounts on the header above the door, and extension (Photo 1), which floats above the upper roller track. In the past, extension springs were safer to install but didn’t have containment cables running through the center of the spring. Without cable, these springs become dangerous, heavy whips when they break. They also tend to be noisier than torsion springs, and we recommend you use them only if you don’t have the 12 in. of headroom above the door that a torsion spring requires.


Those who benefit from this anti-competitive behavior have many excuses for it. They claim that the product is too dangerous and infrequently needed for the public to purchase directly. They say the job is hazardous and requires techniques and tools with which the amateur will rarely practice, which is true. They write me in anger saying I don't understand how expensive it is to put a truck on the road with a technician and parts and salary and benefits and insurance and advertising and every other common business expense. They say it will take the homeowner hours of effort to do this safely and correctly, while they can do it in a fraction of that time and at a price that isn't worth the effort to save. But should they set themselves up as the judge of what you can and cannot do? Of what is an economical use of your time? Imposing minimum order quantities or charging retail prices for small orders is legitimate; inquiring into the purchaser's background is not.

Drive type Garage door openers work in a variety of ways. A chain-drive model raises and lowers doors with a metal chain — these tend to be inexpensive and able to handle heavier doors, but they’re loud. A belt-drive opener uses a belt and operates more smoothly and quietly. Screw-drive openers, which lift doors with a threaded steel rod, are also quiet and don’t require much maintenance. Finally, a direct-drive opener operates as a single unit — the whole contraption moves to lift the door. These tend to be the quietest, smoothest mechanisms available.


Furthermore, newer doors come with more improved security features, helping to improve the way you protect your home and loved ones. While older doors are easy to break into, whether through breaking the lift mechanism or even using a universal garage door remote, new doors come with many redundant security features, which will go a long way in deterring even the most ingenious burglar.

When picking the best garage door for you, a good place to start is with material type. Most garage doors are made from either wood, steel or fiberglass. These three materials are strong, durable and each have their unique benefits at various price points. In order to pick the perfect fit for your home we have developed the DoorView® garage door designer. This interactive visualizer tool helps you design your dream door and allows you to see how it will look on your home with just the push of a button. You can also try it on your Apple iPad and Android devices.


A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.
We believe we should treasure our natural resources, and our business practices reflect this ideal. All our service vehicles are flex-fuel efficient hybrids. When we have to throw away old parts, we recycle as many parts as possible. We clean up our trash after we complete a project. Our dispatch center is conscious about our carbon footprint and we use GPS technology and strategic planning to reduce our miles on the road.
Cable fail-safe redundancy: Based on the proper setting of the drums on the torsion shaft, the two lift cables divide the lifting force equally to keep the door level as it rises. This not only levels the door, but also provides a fail-safe mechanism. If one of the cables should fail, such as from breaking or losing its end attachment, the other cable will then carry the full weight of the door. This will pull the door up on one side with twice the normal force, while the other side falls from its now unsupported weight, tending to make the door bind in its tracks and jam. Although not foolproof, this is a safety feature of the design which keeps the door from falling catastrophically if a cable were to fail while the door was traveling. The jammed condition also prevents a lowered door from opening with the hazard of a single broken cable, further minimizing the chances of both cables failing. Since if one cable fails the other must sustain the full weight of the door, the cables and attachments are rated many times the normal working load of half the door weight. A proper safety inspection of the door should include a critical look at the cables and their attachments.
The history of the garage door could date back to 450 BC when chariots were stored in gatehouses, but in the U.S. it arose around the start of the 20th century. As early as 1902, American manufacturers—including Cornell Iron Works—published catalogs featuring a "float over door." Evidence of an upward-lifting garage door can be found in a catalog in 1906.[4]
The material and style of your door as well as the replacement parts needed will impact the total cost of your project. It would cost less to install a steel door with no opener then it would to install a wood door with an opener etc... High tech doors come with enery-effecient glaze and thick insualation as well as finshed interiors and other upgrades. These doors are more expensive but are more reliable and durable.
This opener is easy to install for most DIYers and comes with two remotes and a wireless keypad so you can open the door with a pin. If you are interested in having this smart-enabled you can purchase a separate kit to do so. The Safe-T Beam helps prevent accidents using a infrared beam that will open or close the door if a car is getting to close. 
Roberto was very courteous and explained the details of what he was doing. He also pointed out a repair I might consider having done (replacement of the bottom panel of my door) and asked the office to follow up with me on this. Someone did follow up with me and since replacement of the bottom panel is not an option and I would have to replace the door, I decided that I can wait.
Install the vertical roller tracks first by wrapping the curved lip around the rollers. The top of these tracks should be approximately 8 in. below the top of the top section. Wait to install the upper tracks until this step is complete. Check the level of the top section to make sure the tops of the vertical roller tracks are level with each other. The bottom of the roller tracks should be at least 1/8 in. off the concrete floor. After leveling and mounting these tracks, install the upper roller (horizontal) tracks.
Smartphone Control: Many newer garage door openers allow you to connect the device to your home's Wi-Fi network, according to RW Garage Doors. You then can open and close the door through a smartphone app. In fact, many of these apps will give you an alert on the smartphone when the garage door is open for a certain period. Some opener models even can connect to your existing Smart Home system, incorporating all your appliances on one system.
Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.
Furthermore, newer doors come with more improved security features, helping to improve the way you protect your home and loved ones. While older doors are easy to break into, whether through breaking the lift mechanism or even using a universal garage door remote, new doors come with many redundant security features, which will go a long way in deterring even the most ingenious burglar.

If you're clever and equipped with a welder, you might think you could get away by welding a broken spring back together. At least two factors make this extremely risky. First, the weld itself may fail, either due to insufficient basic strength, or weakening of the nearby parts of the spring. Second, the fact that the spring was old and fatigued enough to break once, means that it is likely to break again soon at other location(s).
I've provided this information for free, in hopes it will help you either fix your door yourself, or find a competent professional service to do it for you at a reasonable price. If you've been helped by this Web page, as many have, all I would ask is that you create a link to this page (http://www.truetex.com/garage.htm) from any pages you maintain. You will thereby help others searching for complete and reliable information on this type of repair to find it with a Web search.
You might genuinely need some extra parts when you thought you simply needed a broken spring replaced, and a good serviceman will perform a simple inspection to identify such parts. Nor is it unreasonable for a business to charge separately for a service call versus repair work actually performed. But the best protection for you as a buyer, being somewhat at the mercy of whomever you decide to bring on site, is to understand what is being done, and ask intelligently for a clear explanation or demonstration of why extra parts are required.

Garage Door Opener Company

×