Since the springs are winding "up" when the door is closing and going down, the fully closed position is the most stressful on the steel and thus the most likely position at the moment of failure. This is a good thing, because failure near the top-of-travel means that you suddenly have a large, increasing weight falling. Thus we see the principle that you should never be standing or walking under the door when it is opening or closing, especially if you do so manually instead of with an electric opener. When the springs are working correctly, the door appears nearly weightless, but this is an illusion that turns into a calamity when the springs suddenly fail.


When you’re thinking about replacing your garage door, there are many options to consider. Picking out materials and styles is sometimes stressful for homeowners. Neighborhood Garage Door Repair has some helpful tips on choosing the right material for your door. Garage Door Materials Manufacturers offer different materials when it comes to designing a garage door. […]
Horsepower is another key factor when it comes to garage door openers. Look into ½ horsepower garage openers if you have standard aluminum doors. Oversized doors and one-piece doors may require 3/4, 1 or 1¼ horsepower garage door openers. Garage openers with higher horsepower use less effort to operate and minimize wear and tear on the motor. This is ideal if your garage doors act as the main entrance to your home.
The right side of the photo shows the center bearing plate where the stationary cones attach with two bolts. Some doors may have only one spring rather than two equal ones as shown here (indeed, old marks on the shaft show that this door originally had one spring about twice as long on one side). Above the center bearing plate is the bracket and track from the electric opener.
The Lifestyle garage door screen is a fully retractable garage screen door that works with your existing garage door. The Lifestyle features an industry first, fully retractable passage door for ease of entry and exit without having to retract the entire system. The Lifestyle garage screen is fully spring loaded, making opening and closing quick and easy.
I mentioned earlier that this apparatus had at least one prior spring replacement, with a single longer spring having been replaced by two shorter springs. The clamping of the original spring had pressed dimples and an eccentric distortion into the hollow shaft. While this distortion was large enough to block the old cones from sliding across, I was able to remove the old hardware by just sliding them in the other direction. I did not have to bother trying to press out this distortion, since I could just work around it.
This page is a description of how I replaced torsion springs on a garage door. You may find that my experience either frightens you from trying such a stunt yourself, or encourages you to give it a try. You may curse me for revealing the techniques supposedly known only to the trade, or perhaps thank me for explaining how it's done. All the secrets are revealed below. Even if you hire this work out, just knowing how it is done will help you shop for the best deal and avoid falling prey to overcharging tricks.

Since 1975, Kitsap Garage door has provided Kitsap Penninsula with reliable, comprehensive and responsive residential and commercial garage door repair, maintenance and installation services. At Kitsap Garage Door, our primary focus is offering Bremerton, Shelton and Kitsap, WA, home and business owners with the highest quality products and services, as well as exceptional customer experiences marked with free service estimates, workmanship warranties, reliable support and emergency services.


The material and style of your door as well as the replacement parts needed will impact the total cost of your project. It would cost less to install a steel door with no opener then it would to install a wood door with an opener etc... High tech doors come with enery-effecient glaze and thick insualation as well as finshed interiors and other upgrades. These doors are more expensive but are more reliable and durable.
Cycle lifetime unchanged by diameter-versus-length tradeoffs: Since the material stress (and thus cycle lifetime) for equal torques varies only with d, and not D or N, trading coil diameter (D) for spring length (N) in this fashion has no effect on cycle lifetime. Long and skinny, versus shorter and fatter, they'll wear the same if they have the same wire size and diameter-length product. The game of life is all about wire size when it comes to springs (see below).

We offer industry leading service performed by the best licensed professionals in the region. Whether you need springs replaced, a motor repaired or need a new panel on your door, our service workers will get the job done efficiently and effectively, ensuring that your door is back in working order as soon as possible. We also offer a wonderful preventative maintenance program. This is a cost effective way to ensure that you avoid future problems by having the small, unnoticed issues addressed right away.
You garage door is one of your primary entrances to your home so you want to know that they are functioning properly at all times. If you are having complications with your current garage door, then you need to hire a professional garage door company to determine if it needs to be repaired or replaced. Included are the average garage door repair costs in 2016, for the United States. This is the latest information headed into the new year and is a great guide for 2017. I've also included some garage door repair costs pictures, graphics and graphs that include high, low and average costs for garage door repair, installation and replacement costs. It also includes garage door part repair and replacement costs.
Wood garage door: There’s no substitute for the distinctive look of wood. It’s typically made of moisture-resistant cedar, redwood or cypress and offers the most flexibility for custom designs. Depending on climate and exposure, wood doors require more maintenance. The average cost for a 16-by-7 double door made of quality wood: $1,200 to more than $4,000.
Great service all around! Friday night issue with other service company… Aaron’s didn’t turn me down in resolving the fact that I had NO use of my door until Monday. They sent a very well experienced technician on Saturday morning. He was prompt, explained everything very well, advised on next service needs (without being sales-y) and did an awesome job! Thanks again!!!

(The Wahl correction factor accounts for additional stress in the material due to shear forces, although these forces do not contribute to the spring's torque. These shear forces become significant in designs using a low spring index, which is to say, a relatively thick wire for the coil diameter. The correction factor is applied to scale up the stress S to better predict the fatigue lifetime of the spring.)
End treatments: Torsion springs also are made in a variety of end treatments. The "standard torsion end" is most common, as is pictured in my examples, consisting simply of a short, straight length of wire projecting tangentially. Various non-standard end treatments have longer "ears", U-turns, ends bent in toward the center or along the axis, or even loops. Non-standard ends are used in end fasteners peculiar to various manufacturers, which would seem to serve mostly as a guarantee that you buy overpriced replacements from that one source.
Belt driven garage door openers offer a prime level of noise reduction if you want a silent environment in the garage. While common chainlinks will rattle during use, the smooth performance of a belt dampens noise as the garage door slides up and down. Using a 3/4 motor, the Genie SilentMax 750 will easily tackle any typical garage door while keeping the environment quiet and comfortable while in use.
Are you needing garage door repair? Has your garage door opener stopped working, or are you looking to boost your curb appeal? Whatever your garage door need may be, your local authorized Overhead Door™ Distributor is there to assist. You can find the nearest Overhead Door™ Distributor near you today by using our Distributor Locator​ to search your area. ​​
aluminium frames B&D B and D doors and openers BnD Colorbond Custom garage doors cyclone Danmar Doors Garage door insulation garage door insurance garage door motors garage door remote garage door repairs garage door seals garage doors perth garage door springs and cables garage door struts insulated garage doors keyless entry Knotwood lifting cables Merlin garage door motors Merlin garage door openers Perth perth garage door repairs perth garage doors perth garage door servicing replacement remote reprogram garage door remote roller doors sectional garage doors Steel-Line tension springs tracks and rollers wind struts
Today's garage doors come with those door sensors, and if anything is in the path of the door the sensor detects it and raises the door back to the open position. These precautions are important for families with young children or pets. Even if you don't have a mini me or furry friend running around your yard, it's a good idea to have a garage door that is safe for you, your guests and your belongings. 
Spring rate, torque, and lift: The spring rate K for these measurements is π*28.5*10^6 * (0.273)^4 / (32 * 140 * 1.72) = 64.5 IPPT. Applying 7.5 turns on this rate will yield a torque of 7.5 * 64.5 = 484 in-lb, which on the 4-inch drums (2-inch radius) yields a lift of (484 in*lbs)/(2 in) = 242 lbs. Again we find good agreement with the approximate door weight of 238 lbs.
When you’re thinking about replacing your garage door, there are many options to consider. Picking out materials and styles is sometimes stressful for homeowners. Neighborhood Garage Door Repair has some helpful tips on choosing the right material for your door. Garage Door Materials Manufacturers offer different materials when it comes to designing a garage door. […]
You might genuinely need some extra parts when you thought you simply needed a broken spring replaced, and a good serviceman will perform a simple inspection to identify such parts. Nor is it unreasonable for a business to charge separately for a service call versus repair work actually performed. But the best protection for you as a buyer, being somewhat at the mercy of whomever you decide to bring on site, is to understand what is being done, and ask intelligently for a clear explanation or demonstration of why extra parts are required.
When it comes to garage doors, Jarusewski’s Overhead Door Service Inc. is your premiere choice. We are true professionals and your satisfaction is key. Let us show you the quality of our garage doors and how you can improve both the look and value of your home or business. From the appearance of the door, right down to strength and durability, we’ve got a door for everyone.
We only hire and train very experienced technicians, so you can be confident that you will get the best garage door service available. We strive for 100% customer satisfaction on all our work and stand behind our garage door service if you have any issue whatsoever. Our reviews tell of our dedication to excellence and offering the ABSOLUTE best quality products and customer experience. You can check out what our customers have to say about their experience to the Better Business Bureau by clicking here! We guarantee to be the overall top choice in the market for all your garage door needs. We are a family owned garage door company from the Central Kentucky area and only hire technicians that put forth the same honest values that we have. We strive for 100% customer satisfaction and if for any reason that you are unhappy with a technician or their service, we will be happy to make the experience right as we pride ourselves and our company on the highest of customer satisfaction and experience while offering the lowest prices in the market. We are top rated with all service rating and reviewing companies such as BBB, Home Advisor, Demandforce, and Angie’s List. We take our customers experince serious and we guarantee it!

You can reschedule or cancel your service at any time. To reschedule, simply go to Your Orders, find your service order and click on the ‘Contact Provider’ button on Your Orders page. To cancel, click on the 'Cancel Order' button on Your Orders page. Payment goes to the pro from your secure Amazon account. Because you aren't charged until the actual work is completed, cancelling a job doesn't require a refund.
As noted above, set-screw clamping may have distorted the cross-section of the shaft and made it difficult to slide off all the hardware. With the shaft on the floor, it may be possible to restore enough roundness to proceed, using compensating clamping force to the distorted area via a machinist's vise, an arbor press, a hydraulic shop press, etc., on the shaft body. Burrs and other slight distortions on the shaft can be filed off with a hand file or touched with an abrasive wheel on an angle grinder. At some point, the condition of the shaft may just be degraded enough that it ought to be replaced.
Single panel doors can also be installed with (one piece track type hardware) that folds the door back with a single horizontal track on each side (which is mounted at the top of the wood frame) and a roller, (mounted to the top of the door on each side. A hinge on each side that attaches to the bottom of each side of garage door. Using track hardware, a car can be parked much closer to the door, as the whole door, when in the open position, rests completely inside of the garage door header. Track type hardware has much less arc when raising and lowering the garage door as opposed jamb type hardware.[citation needed]
Because your garage door is a major entryway to your home, it is important to keep it in good working order for your own safety, security, and convenience. Choosing the right style and appropriate materials will lessen the amount of repairs that may arise. Additionally, investing in regular maintenance can be cost-effective in the long run. If your garage door is in need of major repair, it is best to call a professional garage door repair company for assistance. Typically, the company will charge for at least one hour for making a service call. However, the benefits of a professional repair job can well outweigh any costs, as a professional can ensure the safety, security, and proper operation of your garage door.
Scott did an amazing job. Your customer service team is excellent. I emailed late on Thanksgiving night my request for service. Your team called my house within 30 minutes and set up an appointment for the following morning. Scott came out and was great. I had purchased the lifetime warranty package with Precision before, and your team delivered. I highly recommend anyone getting a repair to purchase the lifetime warranty package since your team stands behind your product. Rarely do I write reviews - but am happy to share great information on great companies. Thanks for the great service!
We have everything needed and the expertise required to make accurate repairs for every variety of garage door. Whether you have a steel, wooden, or composite garage door, one of our team members will be happy to help you diagnose the problem and then apply an effective solution. Our repair services include repairs for springs, cables, rollers, tracks, sections, and more! Is your door noisy? We know the right way to fix it! Call us any timeyou need us to fix a problem.

With good looks, modest cost, and solid return on your investment, a new garage door is the Triple Crown of curb appeal projects. According to the “Remodeling Impact Report” from the NATIONAL ASSOCIATION OF REALTORS®, the national median cost of a garage door replacement project is $2,300 and recovers 87% of your investment if you sell your house — one of the highest percentage of recovered costs in the “Report.”

Depending on the design, you can know in advance how many turns are going to have to be unwound. Lifting a 7-foot door by winding a cable on a 4-inch diameter (about 1 foot circumference) drum requires about 7 turns, plus one extra turn to maintain cable tension at the top-of-travel. Maintaining tension at the top-of-travel is critical; without it the cable will jump off the drum, requiring a serious repair.
Our reviewers tested a top-rated garage door opener daily for over a week. To get the most comprehensive results possible, they installed it themselves and observed how it performed. We asked our testers to consider the most important features when using this garage door opener, from its drive type to its security features. We've outlined the can’t-miss points here so that you, too, know what to look for when shopping.
However, in addition to potentially causing injuries to the under-prepared DIYer, a malfunctioning door can become a safety hazard to you and your family. Keep in mind, according to the National Electronic Injury Surveillance System (NEISS), over 13000 people checked into hospitals with garage related injuries in the United States in 2007. You don’t want to turn a loved one into a statistic just to save a few dollars!
Now 13 pounds of force must be respected when backed by many hundreds of foot-pounds of stored energy, waiting to be released. Holding this torque is equivalent to stalling a 3 horsepower DC motor. But holding and turning these handles does not require extraordinary human strength. Note that this maximum tangential force depends only on the weight of the door, and the radius of the drums, and is divided by the number of springs (some designs have only one longer spring, as mine did originally, instead of two shorter ones). Higher or lower lift distances imply more or less turns to wind the spring (and thus a different spring geometry), but not more force on each turn.

While a new coat of paint can go a long way in improving the look of your garage door, the truth is that door design has come a long way in the years since garages were first installed in homes. Not only are newer doors more in line with current fashion trends, but they are also better sized for today’s cars. A new, contemporary door is a great way to get an immediate boost on the value of your home.
We are proud of the work we do in Northwestern North Carolina. We love this community and we love serving it. So whether you think you need a small repair or a major overhaul, we want to be the team that helps you increase the value of your home while making it a safer place to live for you and your family. Our professional and friendly sales team are eager to connect with you, so contact us today and find out just how we can ease your concerns and make transform your garage!

We are a family owned and operated company with local offices in various cities. We have offices in Arizona — from Phoenix to Tucson; Nevada— covering the entire Las Vegas metropolitan area, from North Las Vegas to Henderson; the Sunflower State of Kansas, from Wichita to Junction City; Wisconsin — spanning the entire Milwaukee county, from Fox Point to South Milwaukee; and Michigan, with our base in Sterling Heights.
The parts, parts, parts trick: You might be told you need new rollers, cables, drums, bearings, etc., when you don't, or at highly inflated prices. Good questions to ask when first calling for service include, "How do I know you will only charge me for the parts I actually need?", and "If you don't have all the parts I need, what will you charge me to come back?"
There are plenty of garage door accessories to make your garage safer. Sears carries replacement safety sensors that will detect anything in the way and keep it from shutting. If you have a small garage or it's full of gardening equipment, a laser parking assistant will help you find the perfect spot every time. You can set it so it hits the perfect spot on your dash as you pull in. You'll also be able to find new tracks to replace worn opener tracks.
All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
Annual maintenance. Make an annual check of all nuts and bolts on rails and rollers to make sure they’re firmly tightened. Check the condition of all cables to make sure they’re not worn or frayed. Lubricate rollers and springs with a garage-door lubricant (see How to Fix a Noisy Garage Door for maintenance and problem-solving tips). The door should operate smoothly and be properly balanced. Check the balance by disconnecting the opener and lowering the door halfway- the door should hold its position. If it doesn’t, adjust the spring tension or replace the springs.
I was careful not to assume that the previous installation correctly oriented the right- and left-hand springs on the correct sides of the center bearing plate. They could have been installed backwards by an incompetent installer, resulting in them having been wound looser (larger diameter coil) instead of tighter (smaller diameter coil) than when in their relaxed state, and if so I would have corrected them on the new installation. The proper orientation of the springs applies their reaction torque from tighter winding such that it turns the drums to lift the door. Verifying this is a rather simple exercise in mechanical visualization, but does require some care to be certain of correctness. If you were to install the springs backwards, and then start to wind them in the wrong direction, then the torsion bar will start winding the drums backwards, and not holding against the vise pliers, which should be obvious to inspection. Winding a spring backwards also tends to screw the spring off the cones; this error cannot proceed too far before the spring slips off the cones.
An intermediate stage of the garage door opener market eliminated the DIP switches and used remotes preprogrammed to one out of roughly 3.5 billion unique codes. The receiver would maintain a security list of remotes to which it would respond; the user could easily add the unique remote's code to the list by pressing a button on the garage door opener while activating the remote control. The large number of codes made the brute force try-all-possible-digital-codes attacks infeasible, but the systems were still vulnerable to code grabbers. For user convenience, these systems were also backward compatible with the older DIP switch remote codes, but adding an old technology remote to the security list made the garage door opener vulnerable to a brute force attack to find the DIP switch code. The larger code space approach was an improvement over the fixed DIP switch codes, but was still vulnerable to the replay attack.
Stress and lifetime: Calculating the maximal stress in the wire is useful for estimating the lifetime. Using the formula above, the bending stress S in the spring wire is 32*238/(π*0.2253^3) = 212 Kpsi. The spring index C is D/d = 2.23 / 0.225 = 9.88. The Wahl correction factor is Kw = (4C-1)/(4C-4) + 0.615/C = 1.15. The Wahl-corrected stress is Kw * S = 1.15 * 212 Kpsi = 244 Kpsi. This predicts about a 10,000-cycle lifetime, which is the standard "cheap spring" configuration originally installed. Note that while this stress is proportional to the torque being applied, it is also in proportion to the inverse third-power of the wire size. Thus slightly heavier wire sizes (and suitably adjusted D and/or L) radically improve the expected cycle lifetime of the spring.

Next, the torsion shaft is reassembled with the new springs, the drums repositioned loosely on the shaft, this whole assembly slid back into the end bearings, and the drum set-screws tightened down. I tightened the set-screws about 1/2 or 3/4 of a turn after contact with the shaft, which provides a good grip, but does not distort the shaft. The drums can be set on their old positions, if they were correctly installed, which is snug up against the end bearings to remove any longitudinal play in the torsion shaft. Now the lift cable can be reattached to the drums, and a slight temporary torque applied to the shaft to keep the cable taut while the first spring is wound. This temporary torque is conveniently applied with a pair of locking pliers clamped on the shaft, positioned such that they hold the torque by pressing lightly against the wall above the door, before you start the spring winding, The locking pliers stay on the torsion shaft until you have finished the spring winding locked down the spring cone(s) with the setscrew(s), and removed the winding bars. Then you simply remove them with the release on the wrench handle. I feel that any job that doesn't require a trick manipulation with either locking pliers or duct tape (or in the ultimate case, both!) is just too boring. My trusty pliers look a trifle rusty ever since I used them to clamp something on my outdoor TV antenna "temporarily" and left them out in the weather for, oh, several years. The white stuff on the drum is paint overspray from the original painting of the garage interior.
I called and spoke with James the first call i made and he was very helpful and informative. I called the next day and set up an appointment. Nate called and offered to come early . I said that was perfect .he showed up in a clean, well decaled truck and was in full uniform when I met him. He was polite, respectful, knowledgeable and ready to work. His professionalism coupled with his concise and efficient manner was great.I work in a service industry as well and this gentleman is the kind of professional you want knocking on your door. He is definitely an asset to the company. The price is low and the value is high. I will definitely use this company for any of my garage door needs.read more
For more than 35 years, AE Door & Window has served the Cincinnati and Northern Kentucky areas with high-quality Clopay garage door products and exceptional services. We started as a small company operating out of a garage. In the decades since we first opened, we’ve grown into a regional provider that businesses and homeowners turn to when they need garage door products, services and repairs.
Most doors come with electric door openers. After a while these openers malfunction and need to be replaced. If your opener is broken, you're in luck. These repairs don't cost very much and can be replaced easily. You might even be able to do it yourself. Learn how to replace your garage door opener in 15 minutes https://www.youtube.com/watch?v=HeaR6Yhx6IY.
Sterling Door is the only company we trust with our garage door. When our old door acted up, springs, track, etc., they were always timely and got the job done. Then when we made the jump to a new door, they were excellent. They helped us choose the right door, not just pushing the most expensive model. And installation was well done. I recommend Sterling Door for all of your garage door needs.
Make sure the door is balanced. Close the door and pull the emergency release cord (always close the door first so it can’t come crashing down!). Lift the door about halfway up and let go. The door shouldn’t move. If it slides up or down, the torsion spring needs to be adjusted (or maybe even replaced). Adjusting the torsion spring is dangerous, so don’t attempt it yourself (you could get seriously hurt). Call a pro to adjust it.
We are a family owned and operated, local garage door company in the Carlisle area that believes in attention to detail and an emphasis on customer service and satisfaction. We even offer same-day service because we know that when your garage door isn’t working the way it should, you need it fixed fast. We offer affordable rates that will fit your budget, and we’re confident you won’t find another garage door installation company in Carlisle or the surrounding areas with the same dedication to our customers and the quality of our work at the affordable rates we offer our clients.
The deluxe-model upsell trick: Don't you want the best? Don't you want to protect your family? Galvanized springs may be offered to you at extra expense as "longer lasting". Although bare springs (also called "oil tempered") can develop a light film of rust, the eventual failure is due to fatigue and not corrosion. The use of coated springs (whether galvanized, painted, powder-coated, or surface-converted) is mostly about appearance: the customer likes his new door to look shiny, and the customer doesn't like repair parts that show superficial rust from storage.
Ryan came to my rescue within 6 hrs of my call. He was professional, knowledgeable, friendly, and very thorough. He got my door up and running after figuring out what 3 others could not! Don’t try and go the cheapest route like I did because you’ll end up wasting time and money. Hire the pros like Ryan FIRST! If I ever need someone in the future, I’ll be calling them first thing! HIGHLY RECOMMENDread more

My door opener disengaged from the garage door. I made a call in late morning and was given an appointment for late the same afternoon. I received a call in early afternoon asking if I would like an earlier service call. Upon arriving the repair man introduced himself and explained that he would need a few minutes to assess the problem and perform an inspection. When he finished he provided me with a through explanation of the problem, the corrective measures he would take and some suggestions to improve operation. We discussed some options, agreed on the cost and the work was complete within a reasonable time frame. The door operates quieter and with less strain than it ever has. Pleasant, friendly, on-time and reasonably priced. Problem solved. It doesn't get any better than that.


You might be thinking: Aha! Why don't we lift the door, clamp it in place, and install the springs while they are thus safely unwound, rather than deal with all that accumulation of hazardous torque? The answer: At the top-of-travel, the unwound springs are not fully relaxed; they are still clamped to the torsion shaft with a significant stretch along the shaft axis, plus about a half-turn to keep the door snug at the top. This extra length amounts to the stacking of extra turns that accumulate from winding, also termed "spring growth" in the business. In my case this is about 7 turns of 0.2253 wire, or about 2 inches. Stretching the spring that much and clamping it with a half-turn or so of twist is not feasible.
Those who benefit from this anti-competitive behavior have many excuses for it. They claim that the product is too dangerous and infrequently needed for the public to purchase directly. They say the job is hazardous and requires techniques and tools with which the amateur will rarely practice, which is true. They write me in anger saying I don't understand how expensive it is to put a truck on the road with a technician and parts and salary and benefits and insurance and advertising and every other common business expense. They say it will take the homeowner hours of effort to do this safely and correctly, while they can do it in a fraction of that time and at a price that isn't worth the effort to save. But should they set themselves up as the judge of what you can and cannot do? Of what is an economical use of your time? Imposing minimum order quantities or charging retail prices for small orders is legitimate; inquiring into the purchaser's background is not.
A garage door is a large door on a garage that opens either manually or by an electric motor (a garage door opener). Garage doors are frequently large enough to accommodate automobiles and other vehicles. Small garage doors may be made in a single panel that tilts up and back across the garage ceiling. Larger doors are usually made in several jointed panels that roll up on tracks across the garage ceiling, or into a roll above the doorway. The operating mechanism is spring-loaded or counterbalanced to offset the weight of the door and reduce human or motor effort required to operate the door. Less commonly, some garage doors slide or swing horizontally. Doors are made of wood, metal, or fiberglass, and may be insulated to prevent heat loss. Warehouses, bus garages and locomotive sheds have larger versions.
×