Beware of improprer prior installations: Sometimes the existing door installation is not correct, and the old springs should not be used as a specification for replacements. For example, the old springs might have been replaced with incorrect sizes because the last repairman didn't have the right one on his truck. If your door has never worked quite right, something like this might be the cause. To correct this, you must use the weight of the door to specify the spring, either from a spring rate manual giving spring torque constants, or from the formulas below.
Garage door repair is a specialized job, which is typically handled by a garage door repair service. Professional garage door repair technicians can test or repair a garage door system and fix cosmetic blemishes on doors. Common requests include help with jammed or inoperable doors, slow or erratic doors, unusual sounds, dents or scrapes on the door, and general system testing. Garage door repair professionals can work on single-car, double-car and RV-size garage doors.
We lead busy and sometimes hectic lives. It's easy for someone low on sleep and high on stress to accidently bump into their garage door leaving a little damage. If you're lucky it's just an individual garage door panel that's been damaged. This will leave you with the option of garage door panel replacment. There's a chance it might cost you upwards of $150-200 to spot repair damaged garage door panel. If it happens to be an in-production model, they probably will be able to repair or replace the entire panel (if needed) for $250-400. Unfortunately if you've got an older model of garage door the panels may no longer be in production. This might seem like a disadvantage because you'll end up having to just replace the entire door. Many times it's actually easier and more cost effective to just replace the garage door.
In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the project yourself, but you should recruit help for removing the old door.

If you’re looking for a stylish garage door that is a statement of your good taste, we have customized solutions that fit your family’s lifestyle. Or if it’s the safety and security of an integrated, commercial door and operator system that your workplace needs, Overhead Door™ products make operating your facility safer and easier. Our products are manufactured to give you durable, long-lasting performance for years of extended use and trouble-free operation. Each product, from residential to industrial to commercial applications, is backed by knowledgeable and professional customer support for troubleshooting and answers to your questions.


Even if one could somehow stretch and clamp the springs to the proper extra length, the process would still be more trouble, and there would be little or no reduction of risk. Lifting the full weight of the unsprung door by hand and clamping it in the raised position is dangerous in itself, and creates the same amount of stored energy as winding the springs, ready to slip out of your hands. Many doors won't travel far enough up the track to provide clearance to access the springs. You're also going to have to deal with winding stiff steel cables onto both lift drums at once without any resistance to maintain tension. Finally, even if you managed to complete the installation with the door raised, you then have to lower the massive door against an untested balancing torque. If you've made a mistake, then that massive door has nothing but your skeletal force applied through your meat clamps (hands) to prevent it from falling down and crushing whatever is in the way (perhaps your feet?).

Dynamic Door Service can install a new garage door replacement for you quickly and efficiently, conducting thorough testing on your garage door replacement and automatic garage door opener to be sure both are functioning properly.  Investing in a garage door replacement also adds value to your home, since it is one of the best home remodelling projects to recoup cost when you sell your home. Whether you need a new automatic garage door, a garage door replacement, garage door repair or garage door opener replacement or repair, call Dynamic Door Service for prompt, professional automatic garage door installation, maintenance and service.
The door and tracks at this stage of the repair are in a minimum-energy condition. This is a good opportunity to work on any hinges, bearings, rollers, cables, or tracks that need tightening, repair, lubrication, or replacement. Again, these parts should be available from the spring source, and should be ordered based on a pre-inspection. Home-improvement stores carry some of these parts, but the type and quality may not be the best.
The door and tracks at this stage of the repair are in a minimum-energy condition. This is a good opportunity to work on any hinges, bearings, rollers, cables, or tracks that need tightening, repair, lubrication, or replacement. Again, these parts should be available from the spring source, and should be ordered based on a pre-inspection. Home-improvement stores carry some of these parts, but the type and quality may not be the best.

We offer wide range of stainless metal appliqués. Brushed metal effect or painted any RAL colour. Appliqués will suit most demanding design requirements. If you can’t find what you like an option could be your personal design appliqué. Just send a picture or drawing and we will replicate it on your door. Use our recommended designs or create your own:

Manufacturers and distributors of torsion springs believe they are better off not retailing their product directly to the public. They believe they are maintaining higher prices for their product by restricting sales "to the trade." One brochure for parts even flatly stated, "We do not sell to the end user. We protect our dealers," which would seem to be prima facie evidence of an illegal restraint-of-trade scheme. But this is an old story which is true of virtually every product and service, going back to medieval guilds and before.

Lift cable placement: On the standard residential door mechanism, the loops at the lower ends of the two lift cables loop over the two bottom roller shafts which project from the bottom bracket on the door. The upper cable ends fasten to the drums using one of the methods described above. The drums are positioned along the torsion shaft such that the inner edge of each drum is approximately over the edge of the door. The cable winds onto the drum from outside in, so at the top of travel the cable is winding onto the inner edge of the drum, vertical from the edge of the door where it is looped over the roller shaft. As the door is lowered, the cable winds out to the outer edge of the drum, and thus is a bit out from the vertical, but the cable still falls in the gap between the guide rails and door edge. My cables rub and slap on the rails a bit, but after 30 years and many 10,000s of cycles, they don't seem to have worn at all.
You may enter your information on this website, visit an in store associate or call our garage door repair team at the number at the top of this page. Within 24 hours you will receive a call from a local service provider to discuss your requested service. Afterwards, you will schedule a date and time for the service provider to come to your property.
Yet another professional wrote me to say that the red paint on certain components of these assemblies is an "industry standard" that signals, "Danger! Part under hazardous tension." Other items under tension like the bolts on the cable attachment plate on the door should therefore also be painted red. If so, then this is a new, ambiguous, unreliable, and little-publicized standard, because none of my old hardware shows it, red paint also means other things, and searching the Web does not readily turn up references to this practice.
Depending on the design, you can know in advance how many turns are going to have to be unwound. Lifting a 7-foot door by winding a cable on a 4-inch diameter (about 1 foot circumference) drum requires about 7 turns, plus one extra turn to maintain cable tension at the top-of-travel. Maintaining tension at the top-of-travel is critical; without it the cable will jump off the drum, requiring a serious repair.
Had a quick response to my call. thought I might have to wait a couple of days to coordinate their schedule and mine. To my surprise I received service in one and one half hours. Not only that but there was no sales call, technician Mike was fully prepared to give me a quote and complete the work as his vehicle carried everything needed. He very efficiently completed the work and cleaned up after I selected from the options. He replaced the springs all rollers and made needed adjustments expeditiously. I would recommend this firm to anyone needing garage door repairs.read more
The first garage door opener remote controls were simple and consisted of a simple transmitter (the remote) and receiver which controlled the opener mechanism. The transmitter would transmit on a designated frequency; the receiver would listen for the radio signal, then open or close the garage, depending on the door position. The basic concept of this can be traced back to World War II. This type of system was used to detonate remote bombs. While novel at the time, the technology ran its course when garage door openers became popular. While the garage door remote control transmitter is low power and has limited range, its signal can be received by other, nearby, garage door openers. When two neighbors had garage door openers, then opening one garage door might open the neighbor’s garage door as well.
Cost was $88 for 2 pairs of springs, plus $21 shipping. (I had to order 2 pairs to meet the $50 minimum order.) They came with new cones inserted as shown at that price, so I didn't bother trying to remove and reuse the old cones to save a few dollars. The cones are quite difficult to remove from old springs and to insert in new ones, and the spring supplier will have the right tooling to do that easily. That was the best price I could find on the Web at the time, and didn't seem out of line with what parts like this might cost at at the building supply (if they only sold them). Contractors buy these much cheaper in quantities; they're just an ordinary high-carbon steel wire turned on a winding machine. I also found Web sites asking a lot more money, obviously trying to cash in on search-engine traffic from do-it-yourselfers. Others report that some local dealers sell springs at retail, but at a high price that eliminates any economy versus having them installed.
I called and spoke with James the first call i made and he was very helpful and informative. I called the next day and set up an appointment. Nate called and offered to come early . I said that was perfect .he showed up in a clean, well decaled truck and was in full uniform when I met him. He was polite, respectful, knowledgeable and ready to work. His professionalism coupled with his concise and efficient manner was great.I work in a service industry as well and this gentleman is the kind of professional you want knocking on your door. He is definitely an asset to the company. The price is low and the value is high. I will definitely use this company for any of my garage door needs.read more

Insulation, which increases energy efficiency and can help to lower utility bills, is crucial when a garage door is attached to the home. In this case, doors with high R-values are preferred. This means it has insulation that can keep the heat in. The higher the R-value, the better insulated your garage will be against outside noise and cold and hot air.
The history of the garage door could date back to 450 BC when chariots were stored in gatehouses, but in the U.S. it arose around the start of the 20th century. As early as 1902, American manufacturers—including Cornell Iron Works—published catalogs featuring a "float over door." Evidence of an upward-lifting garage door can be found in a catalog in 1906.[4]

When you’ve measured your door and found a replacement that you love, garage door installation and repair services are only a click or call away. Our vast network of independent Clopay Dealers provide dependable service, and are happy to help with regular maintenance and replacement parts after your door is installed. Replacement garage doors installed by our Master Authorized and Authorized dealers are also eligible for a 1-year installation warranty to ensure your door operates reliably. For a quote or to request local service, visit our convenient dealer locator to find a Clopay Dealer near you!
Two of the spring references specifically for the garage-door industry are the APCO Spring Manual by Bill Eichenberger, and the Torsion Spring Rate Book by Clarence Veigel; these give tables of spring sizes and torque constants. Spring engineering principles in general are described in the Handbook of Spring Design published by the Spring Manufacturer's Institute; the formulas allow you to calculate torque constants knowing only the geometry and the Young's modulus of the material. You can also find some brief spring information in standard references like Machinery's Handbook and Marks' Standard Handbook for Mechanical Engineers.
Here's a view of my door and its broken torsion spring. This door is 10 feet wide and 7 feet high, constructed of 3/4 thick hollow wood panels inside with 3/4 inch plywood siding outside to match the house exterior. This is original to the house which was constructed in 1978, and is much heavier (238 pounds, as I measured later as described below) than the steel doors most common today in new construction. The 10-foot width is a little larger than usual for a one-car garage; such doors are typically only 7 or 9 feet wide. The ceiling height is 9 feet, providing 18 inches clearance above the torsion shaft. This is in a 3-car garage with 3 separate extra-wide doors. Every man's dream! ('cept when the door is broke.)
Horsepower You’ll also want to consider the horsepower of your opener. Typically, 1/2 horsepower will work for most doors in newer homes. If you have a heavier solid wood door, though, you may want to opt for 3/4 horsepower so it can lift it with ease. You can also get 1 and 1 1/2 horsepower models, but those are a better fit for commercial or special situations.

Wayne Dalton garage doors are some of the best in the industry. We offer a large selection of garage door designs in many colors and options that can drastically enhance your home’s curb appeal. Not only will a new garage door add beauty to your home, but replacing an old or outdated door with a new one can increase your home’s value. Did you know that year after year replacing the garage door is one of the top home improvement projects for return on investment? Purchasing a new garage door for your home is an excellent investment and we’ve made it even easier to find the perfect door with our Garage Door Design Center or Garage Door Selection Guide.
Clopay Garage doors featuring Intellicore insulation technology represent Clopay Garage doors featuring Intellicore insulation technology represent the ultimate smart choice for homeowners. Clopay Intellicore is proprietary polyurethane foam that is injected into a garage door expanding to fill the entire structure. The result is a door with incredible strength and durability. Its dense insulation also produces a quieter ...  More + Product Details Close
My door opener disengaged from the garage door. I made a call in late morning and was given an appointment for late the same afternoon. I received a call in early afternoon asking if I would like an earlier service call. Upon arriving the repair man introduced himself and explained that he would need a few minutes to assess the problem and perform an inspection. When he finished he provided me with a through explanation of the problem, the corrective measures he would take and some suggestions to improve operation. We discussed some options, agreed on the cost and the work was complete within a reasonable time frame. The door operates quieter and with less strain than it ever has. Pleasant, friendly, on-time and reasonably priced. Problem solved. It doesn't get any better than that.
They sent Doug Fussell out to my house on the day after Christmas! I had only called them three days before! Doug was a premier technician, very thorough and very efficient. I expected him to take two days, since he was replacing two doors and adding openers on each door. He only took the daylight hours of one day! I could not believe how fast he was! In addition, he thoroughly taught me how to use the remote openers. I highly recommend them to anyone!
Speed of a falling door:: Physics tells us that the transit time of a free-falling body is sqrt(2x/g), where x is the length of the fall and g is the acceleration due to gravity (32.2 ft/sec^2). If this typical 150 lb door were to fall an equivalent of 3.75 feet, this falling time would be sqrt(2*3.75/32.2) = 0.48 seconds (480 milliseconds). The terminal velocity is gt, or 0.48 seconds * 32.2 ft/sec^2 = 15.5 ft/sec = 10.6 mph.
First and foremost, a garage door, by design, contains springs designed to balance your door and make it easier to lift. Those springs are under incredible amounts of tension. If a spring breaks or is improperly released, it can cause incredible and potentially fatal injuries. Keep in mind, when working on a garage door spring, it is likely that your face and head will be close to it, meaning that your most sensitive area will be in the direct path of the released spring.

Garage Door Service Co

×