Most situations allow you to replace spring(s) without removing the assembly from the wall, if there is enough clearance in the surrounding garage structure at the ends of shafts. By unbolting the end bearing plates and removing the drums, you can run the springs down to the ends of the shaft to remove and replace the springs. This avoids the balancing act of holding a long, wobbly, heavy shaft while climbing up and down a ladder. This is how the professionals get the job done in a few minutes.
At this point I weighed the unlifted door to confirm and fine-tune my calculations. This is not strictly necessary, but it makes the adjustments easier to perform, if you happen to have a scale with the requisite capacity. With some helpers, we first lifted the door a few inches and rested it on blocks of wood to provide clearance underneath. Then I slid a 400-pound-capacity freight scale under the center of the door, we lifted again to remove the blocks, and lowered the door gently onto the scale. This door weighed in at 238 pounds, which is very heavy for a single-car door. Since the outside of the door carries the 3/4-inch plywood paneling to match the house, and that plywood weighs about 2 lbs/sq-ft, I estimate the door weight to be about 7 x 10 x 2 = 140 lbs of paneling with the rest 238 - 140 = 98 lbs the interior panels, hardware, and cobwebs. Knowing this total weight will help later in adjusting the torsion on the springs. After weighing, we removed the scale and blocks, leaving the door fully lowered again. Had I not had a high-capacity freight scale, I might have improvised a crude weighing device from levers and smaller weights of known mass, or a lever arm pressing a reduced proportion of the full weight onto a lower-capacity scale. Another factor to remember is that The weight of a wood door can vary with humidity.
An enantiomorphic (mirrored) pair of springs, such as my standard door uses, will consist of one left-hand and one right-hand spring. Note that this "right" and "left" has nothing necessarily to do with whether the spring is mounted on the left or right of the center bearing plate. Indeed, with my standard door, if you stand inside the garage, facing out, then the spring to the left is a right-hand-wound spring, and the spring to the right is a left-hand-wound spring. The photos above and below of the broken spring show that it is a right-hand-wound spring.

Keep in mind that when the springs are released there is nothing to help with weight replacement. Garage doors weigh 150 pounds or more and if the door were not locked in place, there would need to be some way of holding it up until it can be lower manually. If no one is available to help, a clamp can be put on the track at the end of the door (Image 1). When ready, release the clamp and take the weight of the door.


You might be thinking: Aha! Why don't we lift the door, clamp it in place, and install the springs while they are thus safely unwound, rather than deal with all that accumulation of hazardous torque? The answer: At the top-of-travel, the unwound springs are not fully relaxed; they are still clamped to the torsion shaft with a significant stretch along the shaft axis, plus about a half-turn to keep the door snug at the top. This extra length amounts to the stacking of extra turns that accumulate from winding, also termed "spring growth" in the business. In my case this is about 7 turns of 0.2253 wire, or about 2 inches. Stretching the spring that much and clamping it with a half-turn or so of twist is not feasible.
The garage door is the gateway to your home. By choosing an Overhead Door™ residential garage door, you are doing more than making a home improvement investment. You are making us a part of your daily life and relying on us for safety, security and dependable operation. Indulge your sense of design with a garage door that sets your home apart with style, appearance, safety and comfort. With dozens of garage door models to choose from, the Overhead Door™ brand provides style and design options to fit every home. ​

While many sites may encourage you to save on garage door replacement costs by installing the door yourself, this is severely discouraged due to safety concerns and the installation techniques and tools required to properly and efficiently replace a garage door. When installing a new garage door, the range of prices also includes the labor performed by the professional garage door technician. These costs can include:
Although you can replace your garage door opener on your own, it’s more difficult than most DIY projects, so following the installation instructions is a must. If you’re not confident you can replace the opener on your own, you should consider hiring a professional, which further increases your costs. You can also expect to pay more if you’re replacing a garage door in addition to the opener.

After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation.


The disaster-is-nigh technique: As he inspects your door, the serviceman grimly calls your attention to "cracks" in your garage door. These appear very faintly in the middle of the door where the panels bow under their own weight when the door is up. This is normal, but the type of thing you wouldn't casually observe yourself. This surprising revelation disarms you, and you may find yourself strangely susceptible to the pitch for an entire new door.
With good looks, modest cost, and solid return on your investment, a new garage door is the Triple Crown of curb appeal projects. According to the “Remodeling Impact Report” from the NATIONAL ASSOCIATION OF REALTORS®, the national median cost of a garage door replacement project is $2,300 and recovers 87% of your investment if you sell your house — one of the highest percentage of recovered costs in the “Report.” 

Carter door: Garage doors in Florida come with extra bracing on the back and are wind-loaded to protect against hurricanes. The average with is 350 lbs. but some can weigh as much as 800 lbs. It can cost up to $1,000 dollars to replace a steel two-car garage door and if it's made of wood it can cost you up to $5,000 dollars. Some customized doors can be as much as 20 - 30k.

Spring Issues - Unless it is due to an obstruction of some type, uneven movement of your garage door is likely caused by a problem with the spring mechanism. Roll-up doors generally have one center-mounted torsion spring. The tension on torsion springs is great. Therefore, it is necessary to call a professional for any repairs to this type of spring mechanism to avoid serious injury. Because replacement of these springs or cables in a garage door can take at least two or three hours of labor, costs can average $300 or more.


We also offer garage door opener repair service. Many times, what appears to be a problem with your garage door is actually a problem with your garage door opener. Our professional technicians have experience with all major garage door opener brands, including the popular LiftMaster line of garage door openers. Whether your garage door opener is making too much noise, failing to turn on, moving too slowly or not opening or closing your door properly, we can fix it fast.
Insulation increases the efficiency of your door and can lower your electric will. You need R-value garage doors. These type of doors keep out hot and cold air and also provide a sound barrier between the outside and your garage. Insulated doors use polyurethane or polystyrene foam as insulation inside the door. More information about garage door replacement cost.

Thus it is humanly impossible to dodge a falling door. If the spring happens to break when the door is moving up or down somewhere in the middle of travel, as is more likely, then you'll have even less time. Hence it is not prudent to stand or walk beneath a moving garage door. Of course people often do, and the only reason this does not frequently kill people is that springs typically break at the bottom of travel, where they are stressed the most.
Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.
Garage doors cause injury and property damage (including expensive damage to the door itself) in several different ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on extension spring systems).
Tom was professional, knowledgeable, and very friendly. He arrived at my house within the time frame he said he would (nothing is worse than a late technician). Once he arrived, he assessed the problem, explained it clearly and concisely, and informed me he had the parts available with him to fix it. He fixed the issues speedily and I was able to return to work within the hour. The price was reasonable too. I would recommend Precision to any of my friends and neighbors. Thanks Tom!
Spring rate and torque: In my spring replacement above, the wire size was d = 0.2253 inches, and the ID was 2 inches, giving a mean diameter D = 2.2253 inches. The number of coils is L/d = 24 inches / 0.2253 = 107, less about 5 dead coils on the winding cones, or 102 active coils. Thus the spring rate is K = (π*28.5*10^6 * (0.2253)^4) / (32 * 102 * 2.2253) = 31.8 in-lb/turn (IPPT). Winding 7.5 turns * 31.8 in-lb/turn yields a torque of 238 in-lbs per spring.
Whether you are a new homeowner looking to personalize your home or you need to replace your existing garage door, Clopay® makes it easy to find the right choice for your home. Your garage door can account for up to 30% of your home’s façade, so choosing the right style can have a great impact on your curb appeal. Clopay doors are available in a variety of styles including carriage-house, raised-panel and modern, all with convenient overhead operation. Choose from a variety of colors, woodgrain finishes, materials and hardware to complement your home’s exterior.
A rolling code is a protocol used by garage door openers to keep your door safe and secure. When the radio signals from your remote control are broadcast to your garage door opener, it uses a specific code to communicate. Older models used the same code every time, making garage door openers vulnerable to burglars using a radio frequency identifier device. 
The technician that came out, Todd Noel, was very friendly and professional. He fixed my problem quickly and did not overcharge me for something that I did not need. He also made some great recommendations for future work. Because of his level of service and my customer experience, I highly recommend Precision and will use them again in the future.
The two set-screws in the winding cones have a 3/8-inch square head, which fits a 3/8-inch open-end wrench or 8-point socket, or a 7/16-inch 12-point socket or 12-point closed-end wrench. I carried an extra wrench in my pocket while winding, since I didn't want to be holding a wound spring that I couldn't set because I had dropped the wrench (although one could rest the winding rod against the door in this case while picking up a dropped tool).
Over the past 15 years, we've been providing professional garage door repair and services to families across the Lehigh Valley and Western New Jersey. We're a family-owned business, and we treat every customer as if they are family as well. We pride ourselves on our dedication to exceptional service. If you are having an issue with your garage door, we can help! We service ALL makes and models of garage doors and garage door openers. Whether you need a repair, a replacement, or routine maintenance, you can rely on us to get the job done at an affordable price.

The usually recommended rule for a door being properly balanced is that it should lift "easily" through all its travel. The door may also remain stationary if let go somewhere around the middle of the travel, but a smoothly rolling door many not show this behavior (while a sticky track will!), so easy travel is the only reliable test for proper balance. A difficult door may be due to stiff bearings or rollers in the mechanism, tracks out of alignment, etc., not necessarily the torsion spring adjustment.
For garage doors with windows, try to match the glass style of your house windows to provide a more consistent look. It’s also recommended that you install insulated windows if your garage is heated or air conditioned. If you opt for an uninsulated garage door, make sure it’s made of thick steel – specifically 24-gauge. Thicker steel will help prevent dents.
Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.
Those who benefit from this anti-competitive behavior have many excuses for it. They claim that the product is too dangerous and infrequently needed for the public to purchase directly. They say the job is hazardous and requires techniques and tools with which the amateur will rarely practice, which is true. They write me in anger saying I don't understand how expensive it is to put a truck on the road with a technician and parts and salary and benefits and insurance and advertising and every other common business expense. They say it will take the homeowner hours of effort to do this safely and correctly, while they can do it in a fraction of that time and at a price that isn't worth the effort to save. But should they set themselves up as the judge of what you can and cannot do? Of what is an economical use of your time? Imposing minimum order quantities or charging retail prices for small orders is legitimate; inquiring into the purchaser's background is not.
Our knowledgeable, dependable and friendly team of professionals can work closely with you to select, design and install a quality garage door that best serves your daily needs, enhances the architecture of your home and fits your budget. The extensively trained and experienced technicians at Kitsap Garage Door can help you with any of your garage door service needs, large or small, and are ready to repair any garage door make or model.

Spring rate and torque: In my spring replacement above, the wire size was d = 0.2253 inches, and the ID was 2 inches, giving a mean diameter D = 2.2253 inches. The number of coils is L/d = 24 inches / 0.2253 = 107, less about 5 dead coils on the winding cones, or 102 active coils. Thus the spring rate is K = (π*28.5*10^6 * (0.2253)^4) / (32 * 102 * 2.2253) = 31.8 in-lb/turn (IPPT). Winding 7.5 turns * 31.8 in-lb/turn yields a torque of 238 in-lbs per spring.
Openers are available with a chain drive, screw drive or belt drive. Chain drives (a long chain pulls the door open and closed) are the least expensive, but they’re loud. Screw drives (a long threaded rod drives a mechanism that opens and closes the door) are priced in the mid- range. They require the least maintenance, but they’re not as quiet as belt drives. Belt drives (a rubber belt opens and closes the door) are the quietest, making them the best choice if you have living space above the garage. They’re also the most expensive.
Location, climate and building codes are just a few factors to consider when determining which type of garage door is right for your home. Depending on the region you live in, you may need to choose a wind load option for your garage door. Wind loaded garage doors help safeguard your home in high wind prone areas. With garage doors serving as the largest and often times the primary entrance to the home, an insulated garage door may also be right for you.
×