Please Note: Prices, promotions, styles and availability may vary by store and online. Inventory is sold and received continuously throughout the day; therefore, the quantity shown may not be available when you get to the store. This inventory may include a store display unit. Online orders and products purchased in-store qualify for rebate redemption. Rebates are provided in the form of a Menards® Merchandise Credit Check valid towards purchases at any Menards® retail store. Not valid for purchases on MENARDS.COM®.
Get a price quote on a New Garage Door- Use our super-simple garage door designer to learn about the available options, pick the ones you like best, and send it to us for a free quote. It's the fastest way to shop for a garage door on the web. In less than 10 minutes, you'll have a much better idea what you want and get a price without sales pressure. Click garage door designer to get started...
When your garage door starts acting up, more often than not it is telling you it's time to do a bit of maintenance. So, before hitting the panic button, try these simple repairs. First, examine the rollers and tracks. If you can't remember the last time you cleaned them (and they look the part!), give them a good brushing and then add some lubricant. Next, perform these simple garage door maintenance tasks.
If you've researched this subject at all, you will no doubt have heard that you shouldn't be attempting torsion spring replacement as a do-it-yourselfer. That is generally good advice, so if you have any doubts about your abilities to do risky physical work on your own, hire the job out like everyone else. I found I was capable of doing this work with acceptable risk, because I intelligently understood the techniques, paid careful attention to methods and safety, knew how to use common tools in good condition, properly improvised the special tools I didn't have, and diligently attended to correctly performing a few moments of hazardous manipulation. I learned to do it purely on my own based mostly on bits of advice reluctantly given in Internet forums such as the Usenet newsgroup alt.home.repair. When I first wrote this page in 2002, there was no other do-it-yourself information available on the Web, and it was not until 2005 that reliable information disclosing the techniques started to appear elsewhere (see links below).
The most common grade of torsion springs have an expected life of about 10,000 cycles. The hardened and tempered steel experiences tremendous forces each time the door opens or closes. Gradually, the steel fatigues with each flexure, and eventually cracks and breaks, usually releasing its stored energy in an instant with a horrific "sproing" noise or bang. If you average about two car trips per day, opening and closing the door a total of 4 times daily when you come and go, then that expected life becomes 2500 days, or only about 7 years. If you have an automatic opener, then if you're like me, you tend to cycle the door even more frequently, and can expect the need for spring replacement even sooner. Moreover, my three-car garage has three doors, so on average I can expect a repair job every few years. Over a lifetime, it is very economical to do these repairs myself.
Given the complexity of a garage door and opener system, there are a variety of different areas something could go wrong. If your garage door shakes or is very loud during operation, the garage door closes all the way only to immediately open back up, the garage door opens slowly or closes too quickly, or the garage door opener and remote aren't working at all, you should seek help from a professional garage door repair specialist.
Here are the new replacement springs I ordered from a distributor, which I found using a Google search for "garage door supply" (search that phrase now). You certainly won't find these at Home Depot or Lowe's (although last I checked Lowe's does carry the less daunting extension spring replacements). I also have a list of some suppliers at the end of this page.
Garage doors are usually located in the home exteriors. As a result, they are directly impacted by the forces of nature causing damage and deterioration of the doors over a period of time. We are specialists of garage doors and know how to handle damaged garage doors in the best possible manner. Professionals in our team have complete knowledge on repair of garage doors and they implement the same in providing the best services to our customers in San Antonio and surrounding areas. We can assure of fixing your garage door problems promptly and that too at the most affordable rates!

Our garage door installation and repair professionals are courteous, knowledgeable, skilled and dedicated to your satisfaction. Let us show you what we’ve done for so many businesses and homes throughout Cincinnati and northern Kentucky when it comes to their garage doors, and what we can do for you. Once you’ve tried our services, you won’t have to search for a garage door service provider in this area ever again.
Recently another type of opener, known as the jackshaft opener, has become more popular. This style of opener was used frequently on commercial doors but in recent years has been adapted for residential use. This style of opener consists of a motor that attaches to the side of the torsion rod and moves the door up and down by simply spinning the rod. These openers need a few extra components to function safely for residential use. These include a cable tension monitor, to detect when a cable is broken, and a separate locking mechanism to lock the door when it is fully closed. These have the advantage that they free up ceiling space that an ordinary opener and rail would occupy. These also have the disadvantage that the door must have a torsion rod to attach the motor to.

When buying an opener, choose a 1/3 hp or 1/2 hp opener for a single garage door (1/3 hp can be hard to find at some home centers). Go with 1/2 hp for a double door and 3/4 hp for a door that has a wood or faux wood overlay (they can be heavy!). Openers have a set opening speed, so installing an opener with a higher horsepower won’t open your door any faster.


While a new coat of paint can go a long way in improving the look of your garage door, the truth is that door design has come a long way in the years since garages were first installed in homes. Not only are newer doors more in line with current fashion trends, but they are also better sized for today’s cars. A new, contemporary door is a great way to get an immediate boost on the value of your home.
The deluxe-model upsell trick: Don't you want the best? Don't you want to protect your family? Galvanized springs may be offered to you at extra expense as "longer lasting". Although bare springs (also called "oil tempered") can develop a light film of rust, the eventual failure is due to fatigue and not corrosion. The use of coated springs (whether galvanized, painted, powder-coated, or surface-converted) is mostly about appearance: the customer likes his new door to look shiny, and the customer doesn't like repair parts that show superficial rust from storage.
Measure springs only when relaxed: Measurements must be taken on a relaxed spring because the winding adds significant overall length while reducing the coiled diameter. If you have a paired design, and one is broken and one is intact, then don't try to measure the length of the intact spring with the door down. A wound spring has 7 or 8 turns adding to the overall length, and will therefore be about 2 inches longer than when relaxed. Measure the lengths of the pieces of the broken spring, which will be unwound, and add them together. As a check, one can measure the length of the intact spring after it is unwound in the procedure to follow below. Be sure also to observe whether the springs are originally of equal sizes, because it is quite possible that they are not.
Lift cable placement: On the standard residential door mechanism, the loops at the lower ends of the two lift cables loop over the two bottom roller shafts which project from the bottom bracket on the door. The upper cable ends fasten to the drums using one of the methods described above. The drums are positioned along the torsion shaft such that the inner edge of each drum is approximately over the edge of the door. The cable winds onto the drum from outside in, so at the top of travel the cable is winding onto the inner edge of the drum, vertical from the edge of the door where it is looped over the roller shaft. As the door is lowered, the cable winds out to the outer edge of the drum, and thus is a bit out from the vertical, but the cable still falls in the gap between the guide rails and door edge. My cables rub and slap on the rails a bit, but after 30 years and many 10,000s of cycles, they don't seem to have worn at all.
I was careful not to assume that the previous installation correctly oriented the right- and left-hand springs on the correct sides of the center bearing plate. They could have been installed backwards by an incompetent installer, resulting in them having been wound looser (larger diameter coil) instead of tighter (smaller diameter coil) than when in their relaxed state, and if so I would have corrected them on the new installation. The proper orientation of the springs applies their reaction torque from tighter winding such that it turns the drums to lift the door. Verifying this is a rather simple exercise in mechanical visualization, but does require some care to be certain of correctness. If you were to install the springs backwards, and then start to wind them in the wrong direction, then the torsion bar will start winding the drums backwards, and not holding against the vise pliers, which should be obvious to inspection. Winding a spring backwards also tends to screw the spring off the cones; this error cannot proceed too far before the spring slips off the cones.
Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.

Once the springs are torqued, the setscrews tightened, and the locking pliers and winding rods removed, do not play with turning the torsion bar using the winding rods. Doing so even momentarily can relieve the tension on the lift cables, which then easily slip off the drums. Replacing the cables on the drums can be difficult without repeating the entire spring unwinding-winding procedure again, and the cables can be damaged if tension is applied while they are off the drums.
Given the complexity of a garage door and opener system, there are a variety of different areas something could go wrong. If your garage door shakes or is very loud during operation, the garage door closes all the way only to immediately open back up, the garage door opens slowly or closes too quickly, or the garage door opener and remote aren't working at all, you should seek help from a professional garage door repair specialist.
Mechanical garage door openers can pull or push a garage door with enough force to injure or kill people and pets if they become trapped. All modern openers are equipped with “force settings” that make the door reverse if it encounters too much resistance while closing or opening. Any garage door opener sold in the United States after 1992 requires safety eyes—sensors that prevent the door from closing if obstructed. Force settings should cause a door to stop or reverse on encountering more than approximately 20 lbs (9.07 kg) of resistance. Safety eyes should be installed a maximum of six inches above the ground. Many garage door injuries, and nearly all garage door related property damage, can be avoided by following these precautions.
We are a family owned and operated, local garage door company in the Carlisle area that believes in attention to detail and an emphasis on customer service and satisfaction. We even offer same-day service because we know that when your garage door isn’t working the way it should, you need it fixed fast. We offer affordable rates that will fit your budget, and we’re confident you won’t find another garage door installation company in Carlisle or the surrounding areas with the same dedication to our customers and the quality of our work at the affordable rates we offer our clients.
Not only was the upward-lifting garage door and the electric garage door opener invented by Overhead Door Corporation’s founder C.G Johnson in the 1920s, but we also have a tradition in excellence for garage door repair, service and maintenance. Even with the most reliable products problems can arise and when they do it’s important to know who to contact to fix these issues while providing solutions to prevent future complications.
It’s important to pick a door that suits the style of your house. If you live in a Craftsman bungalow, for example, you might want something that looks like the swing-out doors found on garages behind early Craftsman houses. Manufacturers of modern roll-up doors make them in styles that mimic the old swing doors, complete with faux strap hinges on the sides and a pair of handles flanking a deep groove in the center. 
Garage door manufacturers typically produce garage doors fitted with torsion springs that provide a minimum of 10,000 to 15,000 cycles and are guaranteed for three to seven years. One cycle is a single opening and closing sequence. Most manufacturers offer a 30,000 cycle spring. However, it is important to remember that if the weight of the garage door is increased by adding glass, additional insulation, or even several coats of paint, the life of the torsion spring may be greatly reduced. Additionally, springs at highly humid environments, such as coastal regions tend to have a significantly shorter cycle life, due to the corrosive cracking.
Torsion springs are devices that lift most of the weight of a garage door so that the door can be opened manually or by an electric opener. The torsion principle is applied via an efficient and economical apparatus consisting of a torsion shaft under spring torsion, which turns lift drums, which wind cables attached to the door near the bottom. All of this apparatus is mounted over the top of the door. The energy stored is sufficient, in an uncontrolled release, to break things, hurt you, or perhaps even kill you. The same could be said of jacking up your car to change a tire, or mowing your lawn, or raising children, so it is not crazy to want to do this yourself.
Single panel doors can also be installed with (one piece track type hardware) that folds the door back with a single horizontal track on each side (which is mounted at the top of the wood frame) and a roller, (mounted to the top of the door on each side. A hinge on each side that attaches to the bottom of each side of garage door. Using track hardware, a car can be parked much closer to the door, as the whole door, when in the open position, rests completely inside of the garage door header. Track type hardware has much less arc when raising and lowering the garage door as opposed jamb type hardware.[citation needed]

Screw-drive garage door openers aren't as popular as some other types, but feedback indicates that those that give the Genie Excelerator a try are largely very happy that they did. It's a fast performer, owners say, and the company claims that it can move a door at a rate of up to a foot per second. It's relatively quiet, too -- perhaps not the absolute quietest that you can buy, but certainly quieter than a chain-drive opener, and quieter than older screw-drive openers, users report.
The prior clamping of the set-screws tends to have pressed a dimple into the hollow shaft and to have distorted the shaft's roundness into an eccentric shape. While releasing the set-screws, I was careful to loosen them enough to let the cone swing around any such distortions. I was also careful to observe any binding of the old cones on the eccentricity or burring on the shaft. The fit of the cone on the shaft is supposed to be loose enough to avoid binding, but if it were to occur one would have to be careful not to assume the spring was unwound when in fact the cone was just stuck on the shaft. If I had a stuck cone that I could not unwind with a little extra force, then I would have called in a technician to deal with it. In the worst case, I suppose the spring must be deliberately broken with some hazard, thus releasing it for a forceful disassembly, and the shaft and some other parts replaced. But this is an unlikely situation and in this case was not necessary.
All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
We also offer garage door opener repair service. Many times, what appears to be a problem with your garage door is actually a problem with your garage door opener. Our professional technicians have experience with all major garage door opener brands, including the popular LiftMaster line of garage door openers. Whether your garage door opener is making too much noise, failing to turn on, moving too slowly or not opening or closing your door properly, we can fix it fast.

The Heavy Duty Chain Extension Kit for 10 The Heavy Duty Chain Extension Kit for 10 ft. High Garage Doors is required for reliable everyday operation of Chamberlain heavy duty chain drive models in 10 ft. garage door applications. Featuring a quick-install extension rail and replacement chain the kit includes everything needed for quick and easy installation. Includes ...  More + Product Details Close
Wayne Dalton garage doors are some of the best in the industry. We offer a large selection of garage door designs in many colors and options that can drastically enhance your home’s curb appeal. Not only will a new garage door add beauty to your home, but replacing an old or outdated door with a new one can increase your home’s value. Did you know that year after year replacing the garage door is one of the top home improvement projects for return on investment? Purchasing a new garage door for your home is an excellent investment and we’ve made it even easier to find the perfect door with our Garage Door Design Center or Garage Door Selection Guide.
×