Stress and lifetime: Calculating the maximal stress in the wire is useful for estimating the lifetime. Using the formula above, the bending stress S in the spring wire is 32*238/(π*0.2253^3) = 212 Kpsi. The spring index C is D/d = 2.23 / 0.225 = 9.88. The Wahl correction factor is Kw = (4C-1)/(4C-4) + 0.615/C = 1.15. The Wahl-corrected stress is Kw * S = 1.15 * 212 Kpsi = 244 Kpsi. This predicts about a 10,000-cycle lifetime, which is the standard "cheap spring" configuration originally installed. Note that while this stress is proportional to the torque being applied, it is also in proportion to the inverse third-power of the wire size. Thus slightly heavier wire sizes (and suitably adjusted D and/or L) radically improve the expected cycle lifetime of the spring.

When ordering springs, be aware that a number of different sizes of springs will make proper replacements, not just the specific size being replaced. The wire size, winding diameter, and length can be traded off to make springs of varied geometry but equivalent torque characteristics. This will also affect the expected lifetime (in cycles) for the spring(s). Since the critical specification for a replacement is the weight it is designed to bear, not the sizes per se, there are likely several stock sizes that replace a given old spring. The spring distributor's inventory may happen to offer only a different size with an equivalent weight-bearing specification. One has to judge whether to trust the advice of the seller in such situations. The seller should have the data to know what substitutions are proper.
Additionally, the B970 includes encryption features that prevent others from hacking the system to gain entry to your garage. Expert reviewers like this garage door opener a lot. The Tool Spy says the Chamberlain B970 justifies its higher price point by delivering excellent build quality and anti-vibration features. Consumer Search and Garage How To also approve of this unit.
In the United States, the Consumer Product Safety Improvement Act of 1990 required that automatic residential garage door operators manufactured on or after 1 January 1991 conform to the entrapment protection requirements of the 1988 version of ANSI/UL standard 325.[11] A requirement for redundant entrapment-prevention devices was added in 1993; such a system can use an electric eye, a door edge sensor, or any other device that provides equivalent protection by reversing the travel of the closing door if an object is detected in its path. [12][13]
If you've researched this subject at all, you will no doubt have heard that you shouldn't be attempting torsion spring replacement as a do-it-yourselfer. That is generally good advice, so if you have any doubts about your abilities to do risky physical work on your own, hire the job out like everyone else. I found I was capable of doing this work with acceptable risk, because I intelligently understood the techniques, paid careful attention to methods and safety, knew how to use common tools in good condition, properly improvised the special tools I didn't have, and diligently attended to correctly performing a few moments of hazardous manipulation. I learned to do it purely on my own based mostly on bits of advice reluctantly given in Internet forums such as the Usenet newsgroup alt.home.repair. When I first wrote this page in 2002, there was no other do-it-yourself information available on the Web, and it was not until 2005 that reliable information disclosing the techniques started to appear elsewhere (see links below).

If you're clever and equipped with a welder, you might think you could get away by welding a broken spring back together. At least two factors make this extremely risky. First, the weld itself may fail, either due to insufficient basic strength, or weakening of the nearby parts of the spring. Second, the fact that the spring was old and fatigued enough to break once, means that it is likely to break again soon at other location(s).
The two set-screws in the winding cones have a 3/8-inch square head, which fits a 3/8-inch open-end wrench or 8-point socket, or a 7/16-inch 12-point socket or 12-point closed-end wrench. I carried an extra wrench in my pocket while winding, since I didn't want to be holding a wound spring that I couldn't set because I had dropped the wrench (although one could rest the winding rod against the door in this case while picking up a dropped tool).
Luckily, there is a bit of science to questions of garage door repair and replacement. That’s why we’ve put together this guide on when to replace a garage door. We’ll prepare you to compare repair vs replacement garage door costs. We’ll discuss the ways in which repairs are the most affordable option while also exploring those moments when replacement will in the end provide you with more value added.
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.

Kevin gave 30 mins advance notice via text before arriving, and he was very friendly and knowledgeable about the Chamberlain garage door opener that we ordered on Amazon. I was pleased with the thorough model description provided, and customer reviews which helped with our decision making, and our package came on the same day that it was ordered! I liked the process of choosing 3 preferred appointment times, and receiving a confirmation email which included Kevin's picture. The install price was very reasonable, and I would gladly use your Home Service again!
Carter door: Garage doors in Florida come with extra bracing on the back and are wind-loaded to protect against hurricanes. The average with is 350 lbs. but some can weigh as much as 800 lbs. It can cost up to $1,000 dollars to replace a steel two-car garage door and if it's made of wood it can cost you up to $5,000 dollars. Some customized doors can be as much as 20 - 30k.
Our reviewers tested a top-rated garage door opener daily for over a week. To get the most comprehensive results possible, they installed it themselves and observed how it performed. We asked our testers to consider the most important features when using this garage door opener, from its drive type to its security features. We've outlined the can’t-miss points here so that you, too, know what to look for when shopping.
End treatments: Torsion springs also are made in a variety of end treatments. The "standard torsion end" is most common, as is pictured in my examples, consisting simply of a short, straight length of wire projecting tangentially. Various non-standard end treatments have longer "ears", U-turns, ends bent in toward the center or along the axis, or even loops. Non-standard ends are used in end fasteners peculiar to various manufacturers, which would seem to serve mostly as a guarantee that you buy overpriced replacements from that one source.
We believe that we are only as good as the technicians we send to your home. As the face of our company, our techs must be well trained, professional, and dependable. This is why we personally hire each one of our technicians and provide them with innovative training, full field experience, and certification before they ever take a call. Our state of the art training facility houses every type of garage door and they become experienced working on every type of opener. You can be confident when you choose Precision Door that the work we do for you will be completed properly, efficiently, and on time.
The torsion shaft with lift drums on the ends is above the door. The standard residential door shaft is a 1-inch outside diameter hollow steel tube. The inside diameters of the bearings, drums, and winding cones are sized to loosely fit that 1-inch diameter shaft. At the center is a bearing plate, on either side of which are the torsion springs, or in some cases just one larger spring. The spring pictured on the left in the photo is broken about 1/4 of the way in from its left end. The black shaft with dangling rope and door bracket is the track for the electric opener.
Many garage door opener remote controls use fixed-code encoding which use DIP switches or soldering to do the address pins coding process, and they usually use pt2262/pt2272 or compatible ICs. For these fixed-code garage door opener remotes, one can easily clone the existing remote using a self-learning remote control duplicator (copy remote) which can make a copy of the remote using face-to-face copying.
Belt driven garage door openers offer a prime level of noise reduction if you want a silent environment in the garage. While common chainlinks will rattle during use, the smooth performance of a belt dampens noise as the garage door slides up and down. Using a 3/4 motor, the Genie SilentMax 750 will easily tackle any typical garage door while keeping the environment quiet and comfortable while in use.
AE Door & Window is that company. You don’t survive and grow for more than 30 years of providing garage door repair service and installation without taking care of your customers. Our reputation for offering quality garage door service is unquestioned. It’s why we have an A+ rating from the Better Business Bureau and countless positive testimonials from satisfied customers.
See the Sectional Overhead Garage Door catalog (PDF file) from the Prime-Line replacement hardware company. Their brochure Sectional Garage Door Torsion Spring Installation Instructions (PDF file, part number GD-12280) is brief but informative. Apparently you can only obtain their torsion springs as special order items through mom-and-pop type hardware stores like Ace and True Value, and not the big-box Home Depot and Lowes.
While you can certainly redo any security features on your garage door, it is often wise to replace the entire door if in fact that is the way a burglar gained access to your house. A new security code may seem like enough, but you don’t know how the thief figured out the old code in the first place. If the motor was disengaged, the issue might be a design flaw in the door itself. The best way to ensure that the thief doesn’t return or another thief doesn’t take advantage of the same unknown security weakness is to install a new door. Again, doing so with give you access to the kinds of robust security features that are being installed and implemented in the newest garage doors on the market.
The lucky-for-you-I-found-another-problem trick: Another trick is to suggest your automatic opener was damaged (or "compromised") by the additional load or shock presented by the failure of the spring(s). The plastic worm gear used in the most common openers (see above) wears normally over the years and tends to leave a lot of debris inside the opener housing. Removing the opener cover reveals a lot of plastic shavings that may be cited as "evidence" you need a new opener, when the gears are actually still serviceable. Nevertheless, you may have indeed worn out the gear if you repeatedly cycled the door with the opener despite having broken springs, which is possible if you have a very lightweight door.
You garage door is one of your primary entrances to your home so you want to know that they are functioning properly at all times. If you are having complications with your current garage door, then you need to hire a professional garage door company to determine if it needs to be repaired or replaced. Included are the average garage door repair costs in 2016, for the United States. This is the latest information headed into the new year and is a great guide for 2017. I've also included some garage door repair costs pictures, graphics and graphs that include high, low and average costs for garage door repair, installation and replacement costs. It also includes garage door part repair and replacement costs. 

If you’re replacing an existing garage door opener in your home, the simplest method for finding the right horsepower is to check the rating of the unit in your garage and get something with equal or higher power. Most homes have single- and double-car sectional garage doors made of aluminum or steel, which is the most affordable type of garage door. These doors are relatively light, so a motor with rating of 1/2 horsepower is more than sufficient. While 1/3 horsepower motors are available, they can wear out faster than those with 1/2 horsepower in such settings, so it’s a good idea to invest a little extra for a more capable garage door opener.
Modern garage door openers include basic to advanced features that improve safety and deter break-ins. Examples include an automatic stop if a descending door encounters a solid object such as the hood of a car and light beam sensors that detect the presence of an object -- or a person or pet -- and stop a garage door's downward movement before accident or injury can occur. Available security options include remote lockouts for when you will be away from home for an extended amount of time, remote codes that change after each use, and lights that turn on automatically when your garage door opens or if movement is detected inside.

You might genuinely need some extra parts when you thought you simply needed a broken spring replaced, and a good serviceman will perform a simple inspection to identify such parts. Nor is it unreasonable for a business to charge separately for a service call versus repair work actually performed. But the best protection for you as a buyer, being somewhat at the mercy of whomever you decide to bring on site, is to understand what is being done, and ask intelligently for a clear explanation or demonstration of why extra parts are required. 

Garage Door Opener

×