Carter door: Garage doors in Florida come with extra bracing on the back and are wind-loaded to protect against hurricanes. The average with is 350 lbs. but some can weigh as much as 800 lbs. It can cost up to $1,000 dollars to replace a steel two-car garage door and if it's made of wood it can cost you up to $5,000 dollars. Some customized doors can be as much as 20 - 30k.
Tom was professional, knowledgeable, and very friendly. He arrived at my house within the time frame he said he would (nothing is worse than a late technician). Once he arrived, he assessed the problem, explained it clearly and concisely, and informed me he had the parts available with him to fix it. He fixed the issues speedily and I was able to return to work within the hour. The price was reasonable too. I would recommend Precision to any of my friends and neighbors. Thanks Tom!
It you have a tilt-up door, you are looking at a $150 - $200 repair or replacement. If it's a roll-up door it's going to cost you more. Roll-up door spring repair or replacement is usually around $200 - $250 for a 2 car door. If the brackets need to be disassembled to remove the springs due to the shaft not sliding sideways enough it will cost you an additional $50 - $100.
Most importantly, you will be greeted by friendly staff and associates that will help you select the right garage door for your home. We welcome the opportunity to supply, install, and/or repair your garage door as well as answer any door questions you may have. When you choose us, you will quickly discover why thousands of Riverbend area customers from house to house and generation to generation have chosen Dan's Garage Door Service as their “DOOR KEEPER” for over 40 years.
You must use springs that are matched to the weight of the door. You cannot compensate for the wrong size spring by adjusting the number of winding turns. If you do not know a proper spring size, then you or your spring supplier must calculate a proper size (see below) based on an accurate weight (within 5 pounds) of the door. So you must then in turn have an accurate weight.
Home Depot local Service Providers are background checked, insured, licensed and/or registered. License or registration numbers held by or on behalf of Home Depot U.S.A., Inc. are available at homedepot.com/licensenumbers or at the Special Services Desk in The Home Depot store. State specific licensing information includes: AL 51289, 1924; AK 25084; AZ ROC252435, ROC092581; AR 228160518; CA 602331; CT HIC.533772; DC 420214000109, 410517000372; FL CRC046858, CGC1514813; GA RBCO005730, GCCO005540; HI CT-22120; ID RCE-19683; IA C091302; LA 43960, 557308, 883162; MD 85434, 42144; MA 112785, CS-107774; MI 2101089942, 2102119069; MN BC147263; MS 22222-MC; MT 37730; NE 26085; NV 38686; NJ 13VH09277500; NM 86302; NC 31521; ND 29073; OR 95843; The Home Depot U.S.A., Inc. is a Registered General Contractor in Rhode Island and its Registration Number is 9480; SC GLG110120; TN 47781; UT 286936-5501; VA 2705-068841; WA HOMED088RH; WV WV036104; WI 1046796.
If you've researched this subject at all, you will no doubt have heard that you shouldn't be attempting torsion spring replacement as a do-it-yourselfer. That is generally good advice, so if you have any doubts about your abilities to do risky physical work on your own, hire the job out like everyone else. I found I was capable of doing this work with acceptable risk, because I intelligently understood the techniques, paid careful attention to methods and safety, knew how to use common tools in good condition, properly improvised the special tools I didn't have, and diligently attended to correctly performing a few moments of hazardous manipulation. I learned to do it purely on my own based mostly on bits of advice reluctantly given in Internet forums such as the Usenet newsgroup alt.home.repair. When I first wrote this page in 2002, there was no other do-it-yourself information available on the Web, and it was not until 2005 that reliable information disclosing the techniques started to appear elsewhere (see links below).
There are plenty of garage door accessories to make your garage safer. Sears carries replacement safety sensors that will detect anything in the way and keep it from shutting. If you have a small garage or it's full of gardening equipment, a laser parking assistant will help you find the perfect spot every time. You can set it so it hits the perfect spot on your dash as you pull in. You'll also be able to find new tracks to replace worn opener tracks.
Leveling the door: Before commencing the spring winding, to check that you have the door properly leveled on the cables, considering all the factors above that make this a tricky adjustment, apply the winding cone setscrew lightly to lock the (unwound) spring cone temporarily on the torsion shaft, and momentarily lift the door slightly off the floor. Adjust the drum set as needed to level the door, repeating this slight lift test. Loosen the cone setscrew before winding the spring(s).
If your garage door is opening slowly or making a lot of noise, the problem may not be your opener. So before you buy a new one, check for broken or wobbly rollers and brackets. But don’t replace the bottom roller bracket yourself—the cable attached to it is under extreme tension. You’ll need to call a pro. If you’re replacing the rollers, get nylon rollers. They operate quieter than steel rollers and cost only a few bucks more. Next, check the torsion spring (mounted on the header above the door opening) to see if it’s broken. When one breaks, you’ll see a gap in the coils. You’ll need a pro to replace a broken spring.
Ryan, the tech that did the initial inspection and Kyle, the tech that did the installation were both extremely skilled, knowledgeable, and have excellent customer service. They arrived on time as scheduled. Explained well what needs to be done and did the job well. Weâre very pleased and recommend Castle Garage Doors. Weâre giving Ryan, Kyle 10 ð along with Hollie for having excellent customer service in making sure the whole process ran smoothly. Thank you ðð»ðð»ðð» -Grandpa & Grandma Read less
An intermediate stage of the garage door opener market eliminated the DIP switches and used remotes preprogrammed to one out of roughly 3.5 billion unique codes. The receiver would maintain a security list of remotes to which it would respond; the user could easily add the unique remote's code to the list by pressing a button on the garage door opener while activating the remote control. The large number of codes made the brute force try-all-possible-digital-codes attacks infeasible, but the systems were still vulnerable to code grabbers. For user convenience, these systems were also backward compatible with the older DIP switch remote codes, but adding an old technology remote to the security list made the garage door opener vulnerable to a brute force attack to find the DIP switch code. The larger code space approach was an improvement over the fixed DIP switch codes, but was still vulnerable to the replay attack.
You might not think it could get easier than pushing a big button to open a door, but some garage door openers make things even simpler by offering keyless entry and multiple remotes. Many models come with a keyless entry pad that mounts outside the garage door so you can gain access without a remote. While a remote is preferable for most situations, there are times when you need to get into the garage and don’t have it handy, so this is a nice feature to have.
One of these "sproing" events at our house finally motivated me to research how these repairs are done. This happened in 2002, when my wife parked the chariot and shut the door. After the door closed, there was a horrific noise that she could only astutely describe as, "a big spring snapping and vibrating". Although I have hired professionals several times in the past to install or repair garage doors, the difference this time was the innovation of Google and newsgroups like alt.home.repair. I was determined to learn the process and to search for online parts vendors.
Wood - Wood garage doors are sturdy and quite beautiful. However, if you live in a humid climate, your doors will be prone to rotting and splitting. If your wood is painted, you must also factor in the costs of painting as part of your regular maintenance routine. The cost of repairing the wood varies depending on the type. However, average cost to repair a wood panel is $190 to $215.