There’s another reason new doors are superior to old ones: energy efficiency. Keep in mind, garage doors are large, and when they open, they let a lot of outside air into your home. While you may have significant insulation separating your garage from the rest of your home, eventually that temperature differential will start to influence your energy bills.
The special-price don't-tell-my-boss trick: In this scheme, after the technician has worked on your door for a bit, he will grimly notify you that he has discovered an additional repair needed, not just the spring(s). He will offer to do the work at a "special price" if you agree not to tell his boss. This air of conspiracy to get a bargain distracts and disarms you from critically thinking whether you really needed the repair in the first place (likely you don't), and whether the price is really a bargain (likely it isn't).
The usually recommended rule for a door being properly balanced is that it should lift "easily" through all its travel. The door may also remain stationary if let go somewhere around the middle of the travel, but a smoothly rolling door many not show this behavior (while a sticky track will!), so easy travel is the only reliable test for proper balance. A difficult door may be due to stiff bearings or rollers in the mechanism, tracks out of alignment, etc., not necessarily the torsion spring adjustment.
AE Door & Window is that company. You don’t survive and grow for more than 30 years of providing garage door repair service and installation without taking care of your customers. Our reputation for offering quality garage door service is unquestioned. It’s why we have an A+ rating from the Better Business Bureau and countless positive testimonials from satisfied customers.
While winding or unwinding, one must be mindful of the possibility that the spring could break during winding process itself. If that should happen while the spring is significantly torqued, hazardous forces on the winding bar will suddenly become unbalanced, and the bar will take an unexpected jump, possibly injuring your hand or anything else in its path. At the same time, the spring remnants, although captured on the torsion bar, will create a frightening racket that would give the bravest soul a start. So your winding technique should be firmly in control of the rods, and you should not be so delicately perched on a ladder such that a startle will result in a fall.

Since we're using an 18-inch (1.5 feet) winding lever to wind each spring up to 29 foot-pounds, we must apply a maximum tangential force to the end of the winding lever of about 20 pounds. Later we'll see that the actual weight of this rather dense door is 238 pounds, implying a maximum tangential force on the winding levers of only about 13 pounds!
When garage door repair isn’t an option — perhaps the current door is beyond fixing or you want to upgrade to a quieter, more energy-efficient model — it’s time to buy a new one. But choosing a garage door is not as simple as it sounds, even when you know the right size for your home. A wide range of materials, styles and finishes are available, and each factor influences the cost. Garage doors are made of aluminum, steel, vinyl, fiberglass, masonite, wood (typically cedar or mahogany), or a composite of several materials. They may be insulated against cold or heat. Traditional and modern styles include raised panel, carriage house or crossbuck. Most styles have window or arch options, and are available in different wood finishes and neutral colors. Because garage doors account for a large part of a home’s exterior, their appearance is usually a homeowner’s top priority. An attractive garage door can increase a home’s curb appeal and resale value.
Garage door openers make it easy to get your garage open without the struggle or the hassle of facing inclement weather. The latest garage door openers have new features such as timed close, battery backup and improved energy efficiency. Sears carries top-of-the-line garage openers that can run much more quietly and smoothly than old models. With a keypad feature, you'll be able to get into your house using a secure four-digit code. With a few new batteries in your remote, you'll be opening your garage with the push of a button.
The lucky-for-you-I-found-another-problem trick: Another trick is to suggest your automatic opener was damaged (or "compromised") by the additional load or shock presented by the failure of the spring(s). The plastic worm gear used in the most common openers (see above) wears normally over the years and tends to leave a lot of debris inside the opener housing. Removing the opener cover reveals a lot of plastic shavings that may be cited as "evidence" you need a new opener, when the gears are actually still serviceable. Nevertheless, you may have indeed worn out the gear if you repeatedly cycled the door with the opener despite having broken springs, which is possible if you have a very lightweight door.
We specialize in all varieties of garage door repair work. We have the tools and knowledge to get the job done safely. It can be somewhat dangerous to take on a garage door repair on your own, and most garage door companies will advise against attempting a DIY fix. There are some hazards to watch out for when working around these heavy and high tension doors. We recommend you give the experts at Girard's a call to address the issue in a safe and timely manner.
Correct spring size is determined by factors such as the weight and height of the door. You cannot substitute a different spring and just tighten or loosen the winding to make it balance the load. Why? To maintain cable tension under all operating conditions, the spring must retain about one turn of unspent wind-up at the top-of-travel position, which with the lift drum size and door height predetermines the number of turns of winding at the bottom-of-travel; and furthermore the torsion of the fully-wound spring at the bottom-of-travel must be slightly less than that needed to lift the weight of the door when translated by the lift drums.
The standard winding tools are simply a pair of 18-inch lengths of mild steel rod, 1/2-inch diameter. Winding cones can have different socket sizes (such as 5/8 inch instead of 1/2 inch), so it is important to measure the socket and select a matching rod diameter. Also beware that poor-quality cones may have a sloppy fit to the winding bars, and a loose fit presents a severe hazard of slipping at the worst moment; anything more than about an inch or two of play at the handle end is too loose for safety. I bought a 3-foot length of zinc-plated 1/2-inch diameter steel rod from Home Depot for about $3, which conveniently cuts into two halves of just the right length (the store might even cut it for you if you ask). A steel supplier selling at commodity prices might charge about 50 cents or so for such a piece that weighs about 2 lbs. Drill rod would work if used in the annealed condition in which it is originally sold, but the added expense provides no benefit and the brittleness (if it had been hardened and not annealed) would worry me a bit. Rebar, threaded rod, screwdrivers, etc., are absolutely foolish as they will not fit the socket snugly. Aluminum rod is definitely too weak, and will bend under the torque that must be applied. Longer rods would make for more leverage but unwieldly swing; shorter rods make for uncontrollable swing. As we'll calculate below, the 18-inch standard tool length is an appropriate compromise. Note that you do not need 18 inches of ceiling clearance above the torsion shaft to use an 18-inch rod, since you need not swing the rods above horizontal when winding.
Lift cable placement: On the standard residential door mechanism, the loops at the lower ends of the two lift cables loop over the two bottom roller shafts which project from the bottom bracket on the door. The upper cable ends fasten to the drums using one of the methods described above. The drums are positioned along the torsion shaft such that the inner edge of each drum is approximately over the edge of the door. The cable winds onto the drum from outside in, so at the top of travel the cable is winding onto the inner edge of the drum, vertical from the edge of the door where it is looped over the roller shaft. As the door is lowered, the cable winds out to the outer edge of the drum, and thus is a bit out from the vertical, but the cable still falls in the gap between the guide rails and door edge. My cables rub and slap on the rails a bit, but after 30 years and many 10,000s of cycles, they don't seem to have worn at all.
Most wood doors are sectional roll-up doors, though a swing-up wood door that’s meant to be painted can be affordably built in the driveway from a wood framework and plywood. Custom wood doors are typically made of durable softwoods such as Douglas fir, cedar, redwood or cypress, or from hardwoods such as oak or mahogany. Appearance-grade hardwoods are relatively expensive.
In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the project yourself, but you should recruit help for removing the old door.

The Ryobi Ultra-Quiet Garage Door Opener boasts a The Ryobi Ultra-Quiet Garage Door Opener boasts a 2HPs motor giving you faster openings and prolonging motor life. An integrated long-lasting LED light keeps your garage illuminated and ensures you don’t spend time changing out light bulbs. Download the Ryobi Garage Door Opener App to monitor and control your garage ...  More + Product Details Close
×