When ordering springs, be aware that a number of different sizes of springs will make proper replacements, not just the specific size being replaced. The wire size, winding diameter, and length can be traded off to make springs of varied geometry but equivalent torque characteristics. This will also affect the expected lifetime (in cycles) for the spring(s). Since the critical specification for a replacement is the weight it is designed to bear, not the sizes per se, there are likely several stock sizes that replace a given old spring. The spring distributor's inventory may happen to offer only a different size with an equivalent weight-bearing specification. One has to judge whether to trust the advice of the seller in such situations. The seller should have the data to know what substitutions are proper.

By watching the chalk mark while winding, you can count the number of turns applied, and confirm the number later. My standard-size door (7 foot height) with 4-inch drums has a nominal wind of 7-1/4 or 7-1/2 turns, which leaves 1/4 or 1/2 turn at the top-of-travel to keep the lift cables under tension. After 7 turns on the first spring, I clamped down the set-screws, weighed the door again, and found a lift of about 100 pounds in reduced weight. As expected, this wasn't quite half of the full 238 pounds, nor would it leave any torsion at the top-of-travel, so I added an 8th turn. The door now weighed 122 pounds on one spring, which was ideal. After winding the other spring, the door lifted easily, with only a few pounds apparent weight. This confirmed that the spring choice was properly matched to the door design. I engaged the electric opener trolley, and adjusted the opener forces down to a safer level suitable for the new, improved balance. The door was now ready for return to service.
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
If this manipulative, we-are-your-nanny business approach is truly in our best interests as consumers, then we shouldn't be allowed near ladders, lawn mowers, or power tools. Those products are just as hazardous and prone to misuse as torsion springs, yet no one thinks of them as forbidden. The only genuine difference is that torsion springs are a hazardous thing you need only rarely, while a lawn mower is a hazardous thing you need all the time.
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
Most garage door openers are pretty expensive. So if you need an opener on a budget, the Genie 1035-V (also known as the Genie Chain Drive 500) gives you that desirable low price point. It doesn't have a lot of high-end tech features, nor will it manage heavy garage doors, but it does the basic work of raising and lowering the garage door perfectly well.

There are plenty of garage door accessories to make your garage safer. Sears carries replacement safety sensors that will detect anything in the way and keep it from shutting. If you have a small garage or it's full of gardening equipment, a laser parking assistant will help you find the perfect spot every time. You can set it so it hits the perfect spot on your dash as you pull in. You'll also be able to find new tracks to replace worn opener tracks.
You must use springs that are matched to the weight of the door. You cannot compensate for the wrong size spring by adjusting the number of winding turns. If you do not know a proper spring size, then you or your spring supplier must calculate a proper size (see below) based on an accurate weight (within 5 pounds) of the door. So you must then in turn have an accurate weight.
Fortunately, owners aren't bashful about weighing in on their garage door openers. Though some models get only a handful of reviews others receive hundreds of unique ratings on sites such as Amazon, Home Depot and Lowe's. If you are interested in a Craftsman garage door opener, Sears is the place to visit. While our research reveals that no garage door opener is perfect, several models jump to the fore as offering good performance and good value in the eyes of owners. These are the openers that we've named Best Reviewed for this edition of our report.
Garage door openers manufactured and installed in the United States since 1982 are required to provide a quick-release mechanism on the trolley that allows for the garage door to be disconnected from the garage door opener in the event of entrapment. [8] Garage door openers manufactured since 1982 are also required to reverse the garage door if it strikes a solid object.[9][10]
The disaster-is-nigh technique: As he inspects your door, the serviceman grimly calls your attention to "cracks" in your garage door. These appear very faintly in the middle of the door where the panels bow under their own weight when the door is up. This is normal, but the type of thing you wouldn't casually observe yourself. This surprising revelation disarms you, and you may find yourself strangely susceptible to the pitch for an entire new door.

Openers are available with a chain drive, screw drive or belt drive. Chain drives (a long chain pulls the door open and closed) are the least expensive, but they’re loud. Screw drives (a long threaded rod drives a mechanism that opens and closes the door) are priced in the mid- range. They require the least maintenance, but they’re not as quiet as belt drives. Belt drives (a rubber belt opens and closes the door) are the quietest, making them the best choice if you have living space above the garage. They’re also the most expensive.
Extremely straightforward and efficient estimating and installation process. We purchased a Clopay sectional steel garage door for our double garage that works flawlessly with our existing door operator. The guys suggested an insulated door, but I thanked them and said no because I don't care for the garage to warm up in the winter and create a corrosive atmosphere of melting snow and salt. Great job!
A garage door is a large door on a garage that opens either manually or by an electric motor (a garage door opener). Garage doors are frequently large enough to accommodate automobiles and other vehicles. Small garage doors may be made in a single panel that tilts up and back across the garage ceiling. Larger doors are usually made in several jointed panels that roll up on tracks across the garage ceiling, or into a roll above the doorway. The operating mechanism is spring-loaded or counterbalanced to offset the weight of the door and reduce human or motor effort required to operate the door. Less commonly, some garage doors slide or swing horizontally. Doors are made of wood, metal, or fiberglass, and may be insulated to prevent heat loss. Warehouses, bus garages and locomotive sheds have larger versions.
In each of our branches, we have the best team of expert professionals who know how to handle each and every type of garage door and its components. This is because all of our technicians go through a rigorous training process, covering every known garage door repair technique. We do not let them onto the field until we know that they are completely trained, and can perform a job to perfection. Aside from this, they are continually updated with all the latest knowledge, information and training in order to do their work efficiently.

While you can certainly redo any security features on your garage door, it is often wise to replace the entire door if in fact that is the way a burglar gained access to your house. A new security code may seem like enough, but you don’t know how the thief figured out the old code in the first place. If the motor was disengaged, the issue might be a design flaw in the door itself. The best way to ensure that the thief doesn’t return or another thief doesn’t take advantage of the same unknown security weakness is to install a new door. Again, doing so with give you access to the kinds of robust security features that are being installed and implemented in the newest garage doors on the market.
If your door feels heavy, it is likely that your springs have started to wear down and are no longer capable of bearing the weight that they once did. Now, don’t worry, just because a spring is starting to lose its strength doesn’t mean it will snap at any moment. However, simultaneously, a weak spring isn’t any safer to try and repair on your own.
When your garage door starts acting up, more often than not it is telling you it's time to do a bit of maintenance. So, before hitting the panic button, try these simple repairs. First, examine the rollers and tracks. If you can't remember the last time you cleaned them (and they look the part!), give them a good brushing and then add some lubricant. Next, perform these simple garage door maintenance tasks.
Screw-drive garage door openers are another type of direct-drive garage door opener. The screw-drive's relatively simple mechanism, which moves up and down a threaded steel rod, makes for a powerful, low-maintenance garage door opener. They are quieter than chain-drive openers, and are fast workers, but, like direct-drive openers, they tend to be pricey.
Another recent innovation in the garage door opener is a fingerprint-based wireless keypad. This unit attaches to the outside of the garage door on the jamb and allows users to open and close their doors with the press of a finger, rather than creating a personal identification number (PIN). This is especially helpful for families with children who may forget a code and are latchkey kids.
One might stack lumber or arrange some other low platform for a steady footing, instead of the ladder. The aluminum ladder shown here is the splendid 16-foot Krause Multimatic, which carries a Type 1A Industrial rating (300 pound working load); I highly recommend it. However, product liability apparently forced this company into bankruptcy in September 2000 and the company ceased operations in June 2001; see http://www.krauseladders.com (this Web site went dead sometime in mid-2002). The world is a dangerous place.
Garage door repair is a specialized job, which is typically handled by a garage door repair service. Professional garage door repair technicians can test or repair a garage door system and fix cosmetic blemishes on doors. Common requests include help with jammed or inoperable doors, slow or erratic doors, unusual sounds, dents or scrapes on the door, and general system testing. Garage door repair professionals can work on single-car, double-car and RV-size garage doors.
Drive type Garage door openers work in a variety of ways. A chain-drive model raises and lowers doors with a metal chain — these tend to be inexpensive and able to handle heavier doors, but they’re loud. A belt-drive opener uses a belt and operates more smoothly and quietly. Screw-drive openers, which lift doors with a threaded steel rod, are also quiet and don’t require much maintenance. Finally, a direct-drive opener operates as a single unit — the whole contraption moves to lift the door. These tend to be the quietest, smoothest mechanisms available.
Spring rate and torque: In my spring replacement above, the wire size was d = 0.2253 inches, and the ID was 2 inches, giving a mean diameter D = 2.2253 inches. The number of coils is L/d = 24 inches / 0.2253 = 107, less about 5 dead coils on the winding cones, or 102 active coils. Thus the spring rate is K = (π*28.5*10^6 * (0.2253)^4) / (32 * 102 * 2.2253) = 31.8 in-lb/turn (IPPT). Winding 7.5 turns * 31.8 in-lb/turn yields a torque of 238 in-lbs per spring.
Chris was very professional & thorough. He arrived on time & was able to answer all questions that I had. I was extremely satisfied with the quality of the work he performed. I spoke several times on the phone with Mrs. Carol who keep me informed prior to, during, and after the installation of my garage door. She was very professional, easy to talk with and resolved any misunderstanding that I had.

Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.
Angle iron provides a stronger installation and reduces vibration, which helps extend the opener’s life span. In an unfinished garage, attach the angle iron directly to the face of a joist with 1-in. lag screws. For finished ceilings, attach angle iron along the bottom of a joist with 3-in. lag screws. Hang the opener using two more lengths of angle iron and nuts and bolts. Use lock washers or thread-locking adhesive to keep vibration from loosening the nuts.
Squealing, screeching, or grinding noises from your garage door are usually indicative of a lack of lubricant or an accumulation of dirt or debris in the tracks. When removing debris, do not use harsh chemicals to clean the tracks. Once the track is clean, coat it with lubricant designed especially for garage doors, if possible. If you do not have access to this special type of lubricant, you can use WD-40 on the tracks and hardware.
All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
Chris was very professional & thorough. He arrived on time & was able to answer all questions that I had. I was extremely satisfied with the quality of the work he performed. I spoke several times on the phone with Mrs. Carol who keep me informed prior to, during, and after the installation of my garage door. She was very professional, easy to talk with and resolved any misunderstanding that I had.
Security Lights: Most newer garage door openers have at least two bright light bulbs, as well as lights activated by motion. On the other hand, some older or cheaper openers are limited to a single light bulb. This doesn't help much with a garage darkened by shadows, leaving you unsure if the rustling in the corner is your cat … or a skunk that snuck into the garage.
Ryan came to my rescue within 6 hrs of my call. He was professional, knowledgeable, friendly, and very thorough. He got my door up and running after figuring out what 3 others could not! Don’t try and go the cheapest route like I did because you’ll end up wasting time and money. Hire the pros like Ryan FIRST! If I ever need someone in the future, I’ll be calling them first thing! HIGHLY RECOMMENDread more
The most common problem with garage door openers is the door reversing when it’s closing, even when there’s nothing obvious obscuring the photoelectric eyes. If your closing force is adjusted correctly, then the problem is almost always the photoelectric eyes. The eyes are very sensitive— even cobwebs can interfere with them. First make sure the eyes are still in alignment (some- thing may have knocked them out of whack). Then make sure the eyes are clean and the path between them is clear. Finally, look for loose wires in the eyes and the opener.
A1 Garage Door Service is known for providing only the best value for money. We always aim for the best possible customer service and experience, reasonable costs for our products and services, give FREE estimates and FREE professional advice as well as amazing deals and discounts when you book our service. What’s more, we GUARANTEE that we service all manufacturer warranties, including lifetime warranties. What more can you ask for?

Garage doors cause injury and property damage (including expensive damage to the door itself) in several different ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on extension spring systems).

The electronics should also be inspected before or after investing in the cost of replacing the garage door panel to make sure your door will operate properly. The sensors prevent the door from closing on someone's foot or a pet. If they don't work, someone could be injured. Also check to make sure the door opener works, since you could otherwise be locked out of your garage.
You'll never ask yourself that question again. Just look at your phone to know for sure. Most smart garage door openers will tell you if it's open or shut. They'll send a message every time your garage door is opened or closed too, if you like. Electric garage door openers provide a huge amount of convenience and safety. Imagine you're in a hurry, it's raining out, you pull out of the garage then press the button on your garage door opener remote. The garage door closes, and you didn't have to get out of your car.
×