Most electric garage door openers have two lights: one in front of the opener and one behind or sometimes they sit side by side. They should provide enough light for you to get into your home from your car. Generally, people don’t leave the garage light on when it’s not in use, so it’s nice to have a temporary light when you arrive home. The length of time the light stays on varies according to how it is programmed. In most instances, you don’t need more than a few minutes from the time you leave the car to when you enter your home.

Horsepower: The horsepower measurement, often shortened to HP, describes the power the garage door opener motor has. A motor with a greater horsepower measurement will open and close the door more quickly, while also being able to handle larger and heavier doors. Motors between 1/2 HP and 1 HP are the most common for residential garages, FeldCo says.

The replacement springs in my case proved to be 0.2253 wire size, 2.0 inch (inside) diameter, and 24 inches long, in a pair of one left- and one right-hand winding. Actually, the old springs in these pictures were a slightly smaller size, but another similar door on this garage was better balanced by that size. Whoever installed the old springs didn't quite get the weight and size just right; it is not unusual to find a repair service installing a slightly off-balance spring size that happened to already be on the truck during the service call. My electric opener had no trouble handling the small imbalance. But since it is safer to reduce the electric operating force as much as possible through careful balancing, I chose the size that was working better on the other door. The Chamberlain brand electric openers (also sold by Sears) I have incorporate a plastic worm gear that tends to wear out after some years of use, requiring a disassembly and installation of a $20 repair kit; this wear is minimized by a properly balanced door.

Thus it is humanly impossible to dodge a falling door. If the spring happens to break when the door is moving up or down somewhere in the middle of travel, as is more likely, then you'll have even less time. Hence it is not prudent to stand or walk beneath a moving garage door. Of course people often do, and the only reason this does not frequently kill people is that springs typically break at the bottom of travel, where they are stressed the most.


Reduce your monthly energy bill with insulated garage doors. They feature an insulated core made of polystyrene that’s surrounded by a steel cover. This can help you maintain the temperature inside your home no matter if it’s extremely hot or cold outdoors. Insulated garage doors are also known for their quiet operation. Be sure to look at the insulation rating – or R-value – when considering garage doors. The higher the R-value, the better the insulation.
Spring Issues - Unless it is due to an obstruction of some type, uneven movement of your garage door is likely caused by a problem with the spring mechanism. Roll-up doors generally have one center-mounted torsion spring. The tension on torsion springs is great. Therefore, it is necessary to call a professional for any repairs to this type of spring mechanism to avoid serious injury. Because replacement of these springs or cables in a garage door can take at least two or three hours of labor, costs can average $300 or more.

You’ll never have a difficult time reaching us here at Absolute Overhead Door. You will speak to another person 24/7 – never an answering machine or computer – no matter if you call day or night. Our team will always be ready to answer any questions that you may have and get a plan and schedule underway to fix everything from a broken spring, garage door opener, to a broken garage door that needs complete and new installation. If you need us to replace broken springs, you or your teenage driver backed into the garage door, or in the market for a new door install or upgrade, we’ve got you covered! We provide garage door service from 8am to 6pm – with no extra charge for evenings and Saturday’s. Absolute Overhead Door Service also provides 24-hour Emergency Service with minimal charge. We are your garage door repair and broken spring experts! If you have an unknown issue with your garage door or an issue with your garage door opener, give us a call today for guaranteed same day service. 


Extension spring systems should always be restrained by a safety cable that runs through the middle of the spring, tying off to a solid point at the rear and front of the horizontal door track. Extension springs represent a hazard to bystanders when a spring, pulley, or cable breaks under tension. Metal parts from extension spring systems can suddenly be launched.

I called and spoke with James the first call i made and he was very helpful and informative. I called the next day and set up an appointment. Nate called and offered to come early . I said that was perfect .he showed up in a clean, well decaled truck and was in full uniform when I met him. He was polite, respectful, knowledgeable and ready to work. His professionalism coupled with his concise and efficient manner was great.I work in a service industry as well and this gentleman is the kind of professional you want knocking on your door. He is definitely an asset to the company. The price is low and the value is high. I will definitely use this company for any of my garage door needs.read more

Lift cable placement: On the standard residential door mechanism, the loops at the lower ends of the two lift cables loop over the two bottom roller shafts which project from the bottom bracket on the door. The upper cable ends fasten to the drums using one of the methods described above. The drums are positioned along the torsion shaft such that the inner edge of each drum is approximately over the edge of the door. The cable winds onto the drum from outside in, so at the top of travel the cable is winding onto the inner edge of the drum, vertical from the edge of the door where it is looped over the roller shaft. As the door is lowered, the cable winds out to the outer edge of the drum, and thus is a bit out from the vertical, but the cable still falls in the gap between the guide rails and door edge. My cables rub and slap on the rails a bit, but after 30 years and many 10,000s of cycles, they don't seem to have worn at all.

And for some extra features, you'll appreciate accessing the system through the MyQ smartphone app. You can set up this Chamberlain opener to automatically close the door after 1, 5, or 10 minutes, which is great for people who are a bit forgetful. We also really like the motion-detecting control panel, which turns on lights whenever it records nearby movement.

When picking the best garage door for you, a good place to start is with material type. Most garage doors are made from either wood, steel or fiberglass. These three materials are strong, durable and each have their unique benefits at various price points. In order to pick the perfect fit for your home we have developed the DoorView® garage door designer. This interactive visualizer tool helps you design your dream door and allows you to see how it will look on your home with just the push of a button. You can also try it on your Apple iPad and Android devices.
The parts, parts, parts trick: You might be told you need new rollers, cables, drums, bearings, etc., when you don't, or at highly inflated prices. Good questions to ask when first calling for service include, "How do I know you will only charge me for the parts I actually need?", and "If you don't have all the parts I need, what will you charge me to come back?"
Great!  We specialize in all sorts of garage door repair work.  Working around the garage door can be fairly dangerous if you’re trying to repair this issue on your own.  Most garage door companies will quickly remind folks about this, and it’s true.  Their are some hazards to watch out for when working around these heavy and high tension doors.  We recommend you give an expert a call to address the issue in a safe and timely manner for you.
Recently another type of opener, known as the jackshaft opener, has become more popular. This style of opener was used frequently on commercial doors but in recent years has been adapted for residential use. This style of opener consists of a motor that attaches to the side of the torsion rod and moves the door up and down by simply spinning the rod. These openers need a few extra components to function safely for residential use. These include a cable tension monitor, to detect when a cable is broken, and a separate locking mechanism to lock the door when it is fully closed. These have the advantage that they free up ceiling space that an ordinary opener and rail would occupy. These also have the disadvantage that the door must have a torsion rod to attach the motor to.
The "safety issue" trick: Another tip-off is the use of language like "safety issue". This is meant to trump any objections you might have to a costly repair bill. Don't be manipulated by the suggestion that you are risking disaster if you don't buy something expensive. Even if you think the risk is genuine, get another estimate, and tell the second repairman you are skeptical; every technician loves to prove the competition made a mistake.
It you have a tilt-up door, you are looking at a $150 - $200 repair or replacement. If it's a roll-up door it's going to cost you more. Roll-up door spring repair or replacement is usually around $200 - $250 for a 2 car door. If the brackets need to be disassembled to remove the springs due to the shaft not sliding sideways enough it will cost you an additional $50 - $100.
Single panel doors are constructed from one monolithic panel. From the closed position a single panel door swings up and overhead with a hinge on each side (known as jamb type hardware) to the fully open position. A disadvantage of monolithic panel doors is that the swing up arc of the door occurs partially outside the garage. This means a vehicle must stop and park several feet in front of the door to avoid being hit by the garage door when it is opened.
As we’ve mentioned before, springs are installed within your garage lift mechanism in order to help lift the door. Because doors are so heavy, the lift motor would undergo far more significant wear and tear if it had to lift the full weight of the door every time you opened it. Furthermore, in order to ensure that you can open your door even if you lose power in your home, springs allow you to lift the door by hand when the motor is disengaged.
Overhead Door™ products automatically include the unequaled expertise of Overhead Door™ Distributors. Combined with our innovative product design and manufacturing superiority, our distributors are a proud part of the family, sharing our name, Red Ribbon logo, and commitment to excellence. Our network of more than 400 Overhead Door™ D​istributors ensures you have convenient access to our commercial doors and operators, residential garage doors and openers, and accessories wherever you are. This extensive distribution network is unique in our industry, providing a single source for personalized design and application consulting, quick installation, turnkey services and professional maintenance.
We provide Garage door service, repair, sales and estimates for the entire Detroit, Michigan Metropolitan area with service to Wayne, Oakland, Washtenaw, Monroe, Livingston and Macomb Counties. This includes: Ann Arbor, Birmingham, Bloomfield Hills, Canton, clawson, Clinton Township, Commerce Township, Dearborn, Dearborn Heights, eastpointe, Farmington Hills, ferndale, Franklin, Fraser, Garden City, Grosse Ile, Livonia, Macomb Township, Milford, Northville, Novi, Plymouth, Rochester, Romulus, Roseville, Royal Oak, Shelby Township, South Lyon, Southfield, Southgate, Sterling Heights, Taylor, Trenton, Troy, Utica, Warren, Wayne, West Bloomfield, Westland, Ypsilanti, MI.
Since their invention in the 1920s, electric garage door openers have come a long way. Garage door openers work by using a trolley connected to an arm that attaches to the top of the garage door and slides back and forth on a track, which opens and closes the garage door. When operating the motor, a chain or belt turns and pulls the trolley along the track. A good garage door opener will have a horsepower of 1/2 HP, 3/4 HP, or 1-1/4 HP. Garage door openers have the ability to open and close a limited number of times in power outage emergencies. Security is something else to consider when purchasing an opener. It's helpful to have sensors that will stop the operation of the garage door when a person, vehicle, or other obstacle is in the way.
One might stack lumber or arrange some other low platform for a steady footing, instead of the ladder. The aluminum ladder shown here is the splendid 16-foot Krause Multimatic, which carries a Type 1A Industrial rating (300 pound working load); I highly recommend it. However, product liability apparently forced this company into bankruptcy in September 2000 and the company ceased operations in June 2001; see http://www.krauseladders.com (this Web site went dead sometime in mid-2002). The world is a dangerous place.
Single panel doors can also be installed with (one piece track type hardware) that folds the door back with a single horizontal track on each side (which is mounted at the top of the wood frame) and a roller, (mounted to the top of the door on each side. A hinge on each side that attaches to the bottom of each side of garage door. Using track hardware, a car can be parked much closer to the door, as the whole door, when in the open position, rests completely inside of the garage door header. Track type hardware has much less arc when raising and lowering the garage door as opposed jamb type hardware.[citation needed]
Garage Door Installation – This includes the installation of a new garage door. Includes the door itself, the track, cables, springs, hinges, handles, locks and rollers. It is the complete service and installation of a new door. We inspect all the parts, make adjustments to fit your garage opening, and service all elements during the installation process. Plus, we check to ensure all parts are in proper working order after installed.
Door repair business advice (warning to consumers, you are not allowed to know this): Thinner wire is excellent for shortening spring lifetimes, lightening your inventory on a service truck, and getting paid for frequent service calls. This is why your industry chooses to set "standard" springs to have thin wire and despicably short lifetimes. If you want to maximize profits and fleece your customers, install springs that predictably break in about 7 years on a door that should last decades, even though it is just as easy for you to install slightly more expensive springs that should last the life of the door. Remember that the customer wanted the cheapest price, so you need not feel any guilt about this low-balling.
Right-hand versus left-hand winding: Springs are chiral, that is, wound or "laid" in either a left- or right-hand orientation. This is a critical property of their design and specification; you cannot substitute a left for a right or vice versa. If you were to grasp the spring in your hand, and if your right hand orients the tips of your fingers like the ends of the coiled wire when your thumb points "out" of the core of the spring, then you have a right-hand spring; likewise left (which end you grasp does not matter). (This also happens to match the "right hand rule" of magnetic polarity, if you happen to be knowledgeable in such esoteric subjects.) Another way to identify the winding is to examine the spring vertically in front of you; if the coils facing you rise going to the right, it is right-hand (thus you can remember, "rise to the right is right-hand"), and likewise left indicates left-hand. Another way is to view the coil axially; a right-hand spring winds in a clockwise direction as it recedes away, and a left-hand spring counter-clockwise. Yet another way, not so easy to remember, is to hold the spring vertically and compare the coil shape to the letter "Z" (indicates right-hand lay) or the letter "S" (indicates left-hand lay).
Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.
I was careful not to assume that the previous installation correctly oriented the right- and left-hand springs on the correct sides of the center bearing plate. They could have been installed backwards by an incompetent installer, resulting in them having been wound looser (larger diameter coil) instead of tighter (smaller diameter coil) than when in their relaxed state, and if so I would have corrected them on the new installation. The proper orientation of the springs applies their reaction torque from tighter winding such that it turns the drums to lift the door. Verifying this is a rather simple exercise in mechanical visualization, but does require some care to be certain of correctness. If you were to install the springs backwards, and then start to wind them in the wrong direction, then the torsion bar will start winding the drums backwards, and not holding against the vise pliers, which should be obvious to inspection. Winding a spring backwards also tends to screw the spring off the cones; this error cannot proceed too far before the spring slips off the cones.
Customers who have purchased this garage door opener for their homes have been mostly satisfied with the performance of it. Many have raved about how quiet it actually is—one said instead of hearing the metal squeak and clank like with their last one, only the sound of the “wooden door being jostled around as it is pulled up and down” is all you hear with this one. Customers were also happy with the features including the automatic closer when you forget to shut it after you go inside. Some had had issues with the manual being hard to understand while installing it themselves. But most were happy with the overall performance.
Next, the torsion shaft is reassembled with the new springs, the drums repositioned loosely on the shaft, this whole assembly slid back into the end bearings, and the drum set-screws tightened down. I tightened the set-screws about 1/2 or 3/4 of a turn after contact with the shaft, which provides a good grip, but does not distort the shaft. The drums can be set on their old positions, if they were correctly installed, which is snug up against the end bearings to remove any longitudinal play in the torsion shaft. Now the lift cable can be reattached to the drums, and a slight temporary torque applied to the shaft to keep the cable taut while the first spring is wound. This temporary torque is conveniently applied with a pair of locking pliers clamped on the shaft, positioned such that they hold the torque by pressing lightly against the wall above the door, before you start the spring winding, The locking pliers stay on the torsion shaft until you have finished the spring winding locked down the spring cone(s) with the setscrew(s), and removed the winding bars. Then you simply remove them with the release on the wrench handle. I feel that any job that doesn't require a trick manipulation with either locking pliers or duct tape (or in the ultimate case, both!) is just too boring. My trusty pliers look a trifle rusty ever since I used them to clamp something on my outdoor TV antenna "temporarily" and left them out in the weather for, oh, several years. The white stuff on the drum is paint overspray from the original painting of the garage interior.
aluminium frames B&D B and D doors and openers BnD Colorbond Custom garage doors cyclone Danmar Doors Garage door insulation garage door insurance garage door motors garage door remote garage door repairs garage door seals garage doors perth garage door springs and cables garage door struts insulated garage doors keyless entry Knotwood lifting cables Merlin garage door motors Merlin garage door openers Perth perth garage door repairs perth garage doors perth garage door servicing replacement remote reprogram garage door remote roller doors sectional garage doors Steel-Line tension springs tracks and rollers wind struts
Thank you for visiting Precision Garage Door Service of Seattle. We specialize in the repair of residential garage doors, openers, sales, service, & installation. Where ever you live along the Wasatch front, You have my personal guarantee that your experience with us will be professionally handled from start to finish. Your service will be provided by qualified & certified technicians that have completed the most extensive & rigorous training in the industry. We are proud of our environmentally sensitive business practices. Please give us a call to discuss your specific needs. We look forward to serving you.
We’ve been reviewing the best garage door openers for more than half a decade. This year we chose the Chamberlain Premium as our top pick. It’s an efficient, reliable garage door opener, and it comes with a backup battery system that works in a power outage. This model also has a preinstalled timer that closes your garage door automatically so you don't have to worry about whether you left the garage door open.
Here are the winding rods inserted in the winding cone of the unbroken old spring, posed just for a picture. Note that I have carefully placed a sturdy, steady ladder just clear of the swing of the rods, such that when I am standing on the lower rungs to reach the rods, that my head and body are clear of the "kill zone" around the spring and cone. You must have a trustworthy platform to stand on, because a slip or shake of the ladder while you are winding can cause you to lose your socketed attachment to the cone, letting loose the spring. I would not trust an ordinary household step ladder for this purpose.
We have everything needed and the expertise required to make accurate repairs for every variety of garage door. Whether you have a steel, wooden, or composite garage door, one of our team members will be happy to help you diagnose the problem and then apply an effective solution. Our repair services include repairs for springs, cables, rollers, tracks, sections, and more! Is your door noisy? We know the right way to fix it! Call us any timeyou need us to fix a problem.
The Keychain Garage Door Remote offers portable control The Keychain Garage Door Remote offers portable control with the highest level of security. Featuring a three-button design this compact remote controls up to three garage door openers individually. Easily programmed and compatible with nearly every garage door opener made by Chamberlain LiftMaster and Craftsman it’s the easy option for ...  More + Product Details Close

If your garage door's spring breaks, stops working properly, or snaps, you'll lose the ability to open and close your garage door. This could happen due to a variety of issues, like normal wear and tear or from extreme temperature changes in a short amount of time. Spring replacements require a quick response from a garage door provider near you. Contact The Home Depot and a local, background-checked technician will respond within 24 hours.
Safe automatic door openers. All automatic openers must now have an auto-reversing mechanism and photoelectric eyes located near the floor on both sides of the door (see photo). If the door is closing and the beam between the eyes is interrupted, the door will automatically reverse. If the eyes aren’t connected, the door won’t operate. For instructions on how to install a new garage door opener, see How to Install a Garage Door Opener.
Luckily, your garage door is a pretty sound investment. According to Garage Wow Now, garage doors were ranked in the top three for home improvements whose costs are recouped through increased home value. Similarly, realtors regularly increased the list price of a home with a new garage door by 1 to 4 percent! That means, if you spend $2000 on a new garage door, you can increase the value of your home by almost $8000 if you have a $200,000 home. Furthermore, compared with the other two highest rated improvements — siding replacement and deck installation — a garage door replacement is far more affordable.
The Genie Universal Dual Frequency Remote Conversion/Upgrade Kit The Genie Universal Dual Frequency Remote Conversion/Upgrade Kit includes one 3-button compact remote one receiver one transformer and electrical wire (two-wire). The kit alleviates frequency issues from the recently implemented Land Mobile Radio communication system used by military bases as part of the Homeland Security efforts.  More + Product Details Close
×