This is the electric opener which operates this door. I'm picturing it here because you pull the rope to disconnect the trolley, run the trolley under power to the fully-open position, and then disconnect power before working on the door. Then you should lock the door down with either the security lock or with Vise-Grips or C-clamps. This avoids the door lifting when you don't expect it as you are applying spring adjustments. It you were to foolishly overwind the spring without the door locked down, you could possibly find the door trying to leap up to the raised position when you aren't prepared. That would likely knock your grip off the winding rods, with potentially disastrous results. I like to work under the safety principle that serious accidents should be physically possible only when you make two or more stupid mistakes at the same time.
Single panel doors can also be installed with (one piece track type hardware) that folds the door back with a single horizontal track on each side (which is mounted at the top of the wood frame) and a roller, (mounted to the top of the door on each side. A hinge on each side that attaches to the bottom of each side of garage door. Using track hardware, a car can be parked much closer to the door, as the whole door, when in the open position, rests completely inside of the garage door header. Track type hardware has much less arc when raising and lowering the garage door as opposed jamb type hardware.[citation needed]

I obtained my parts, as described on this page, from American Garage Door Supply Inc. (http://www.americandoorsupply.com/) They may have raised their small-order prices or imposed a minimum order since I ordered from them in 2002 at the prices in my essay above. The Web site offers a free catalog by PDF download or mail. Springs in 2005 were priced at $2.25/lb.
When buying an opener, choose a 1/3 hp or 1/2 hp opener for a single garage door (1/3 hp can be hard to find at some home centers). Go with 1/2 hp for a double door and 3/4 hp for a door that has a wood or faux wood overlay (they can be heavy!). Openers have a set opening speed, so installing an opener with a higher horsepower won’t open your door any faster.
Some garage door openers are compatible with HomeLink, a remote control technology that's built into some automobiles. However, due to a technology change, many older HomeLink-equipped cars are not compatible with new HomeLink-enabled garage door openers without the purchase of an optional interface; you can also simply ignore your car's built in controls in favor of the remote control that comes with the opener, but that's a solution that seems to annoy owners.
Once the shaft, springs, and center bearing plate come down and lay on the floor, the old springs should be easy to get off and new ones slid on and assembled. Two bolts hold the center cones to the center bearing plate. The bearing on the center plate can be oiled while it is exposed from having the springs off. At this point it is a relief to be working with inert parts while standing on the floor rather than energized parts while up on the ladder. You might think it would save a little time to replace the spring with the shaft left up on the wall, but I found it was easier and safer to lower the works down to the garage floor first.

Good customer service is important for any product, but it is especially important for the class of garage door openers we considered. We looked primarily at models designed to be installed by a homeowner, not a professional. Even if you consider yourself to be pretty handy, you are sure to have questions at some point along the way. As such, we looked for companies that respond to all inquiries as well as for resources, such as a downloadable manual, to help with installation.
Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.
Repair of garage doors is a licensed trade in many jurisdictions, and manipulation of the market inevitably follows. Look in your phone book yellow-pages under "garage doors" and you'll find a lot of big, costly ads for door service. The profits are quite juicy, I'm sure. The customers need service urgently, and this need will typically arrive suddenly and at a busy time when shopping for prices is not convenient. A few dollars in parts, an hour of labor and travel, and a $150 invoice (assuming the outfit is charging fairly, some are not). Lately (2006) I hear of outfits charging $200 or $300 for this work, and occasionally a story of a $500 or $800 service call. You'll also find the phonebook advertisers waiting eagerly for your call, because artificially high prices inevitably lead to an oversupply of service firms working under capacity.

These are just my observations as a consumer; I am not on a crusade to change the garage door industry. But I will observe that the Web is the innovation that can finally give intelligent consumers the advantage in these commercial games. Trade restraints work only when all sellers in the market collude in and agree to the scheme. If anyone, anywhere is selling freely, then the Web can help you find them. In the years since I have first published this information, a number of reputable Web-based merchants have appeared to supply the parts you need to repair your garage door as a do-it-yourselfer (and I have linked many of them below).

You might be thinking: Aha! Why don't we lift the door, clamp it in place, and install the springs while they are thus safely unwound, rather than deal with all that accumulation of hazardous torque? The answer: At the top-of-travel, the unwound springs are not fully relaxed; they are still clamped to the torsion shaft with a significant stretch along the shaft axis, plus about a half-turn to keep the door snug at the top. This extra length amounts to the stacking of extra turns that accumulate from winding, also termed "spring growth" in the business. In my case this is about 7 turns of 0.2253 wire, or about 2 inches. Stretching the spring that much and clamping it with a half-turn or so of twist is not feasible.
The belt-driven Chamberlain B970 garage door opener is powerful and well-featured. With a 1.25 HPS motor, it's got all of the strength needed for just about any residential garage door, and the motor and belt are covered by a lifetime warranty. The feature line-up includes built-in Internet connectivity for those who want to be able to monitor and operate their opener from afar, and a battery back up in the case of a power outage.
Loosening or tightening the set-screws is the moment of most risk, since the end-wrench is a potential missile if you slip, and your hand is close to the cone. When the wrench is removed and only the rods are in place, it would seem that the worst that could happen is that the rod is flung out and the captive spring and cone rattle around, assuming you are keeping yourself clear of the rod's radial disk of rotation, and not leaning on the rod such as to fall into the apparatus were the rod to slip out of your grasp. The torsion shaft design has the virtue of capturing the mass of the spring and cones reliably on the shaft, preventing these parts from launching themselves as projectiles, even in an accident.

The various increments of standard wire sizes differ by only about 0.010 inch, so calipers or a micrometer would be the tool to use to be certain of the stepped size you have, or else a trustworthy ruler marked in tenths of an inch to use the measure-10-turns-and-divide-by-10 trick. The most common wire sizes in the US are 0.207", 0.218", 0.225", 0.234", 0.243", 0.250", and 0.262".
Sectional: Also known as a raised panel door, this door is the most common. It is made of several horizontal panels hinged together, fitted with wheels and mounted within a track. The biggest advantage of this door is it takes up relatively little space and easily controlled with a standard remote garage door opener for a nominal cost. Their moving parts are readily accessible which can keep repair costs low. The average cost for sectional door repairs is $128.
An extension spring counterbalance system consists of a pair of stretched springs running parallel to the horizontal tracks. The springs lift the door through a system of pulleys and counterbalance cables running from the bottom corner brackets through the pulleys. When the door is raised, the springs contract, thus lifting the door as the tension is released. Typically these springs are made of 11 gauge galvanized steel, and the lengths of these springs are based on the height of the garage door in question. Their lifting weight capacity can best be identified by the color that is painted on the ends of the springs.
When picking the best garage door for you, a good place to start is with material type. Most garage doors are made from either wood, steel or fiberglass. These three materials are strong, durable and each have their unique benefits at various price points. In order to pick the perfect fit for your home we have developed the DoorView® garage door designer. This interactive visualizer tool helps you design your dream door and allows you to see how it will look on your home with just the push of a button. You can also try it on your Apple iPad and Android devices.

These are just my observations as a consumer; I am not on a crusade to change the garage door industry. But I will observe that the Web is the innovation that can finally give intelligent consumers the advantage in these commercial games. Trade restraints work only when all sellers in the market collude in and agree to the scheme. If anyone, anywhere is selling freely, then the Web can help you find them. In the years since I have first published this information, a number of reputable Web-based merchants have appeared to supply the parts you need to repair your garage door as a do-it-yourselfer (and I have linked many of them below).
Customers who have purchased this garage door opener for their homes have been mostly satisfied with the performance of it. Many have raved about how quiet it actually is—one said instead of hearing the metal squeak and clank like with their last one, only the sound of the “wooden door being jostled around as it is pulled up and down” is all you hear with this one. Customers were also happy with the features including the automatic closer when you forget to shut it after you go inside. Some had had issues with the manual being hard to understand while installing it themselves. But most were happy with the overall performance.

Loosening or tightening the set-screws is the moment of most risk, since the end-wrench is a potential missile if you slip, and your hand is close to the cone. When the wrench is removed and only the rods are in place, it would seem that the worst that could happen is that the rod is flung out and the captive spring and cone rattle around, assuming you are keeping yourself clear of the rod's radial disk of rotation, and not leaning on the rod such as to fall into the apparatus were the rod to slip out of your grasp. The torsion shaft design has the virtue of capturing the mass of the spring and cones reliably on the shaft, preventing these parts from launching themselves as projectiles, even in an accident.
The lucky-for-you-I-found-another-problem trick: Another trick is to suggest your automatic opener was damaged (or "compromised") by the additional load or shock presented by the failure of the spring(s). The plastic worm gear used in the most common openers (see above) wears normally over the years and tends to leave a lot of debris inside the opener housing. Removing the opener cover reveals a lot of plastic shavings that may be cited as "evidence" you need a new opener, when the gears are actually still serviceable. Nevertheless, you may have indeed worn out the gear if you repeatedly cycled the door with the opener despite having broken springs, which is possible if you have a very lightweight door.
If you’re looking for a stylish garage door that is a statement of your good taste, we have customized solutions that fit your family’s lifestyle. Or if it’s the safety and security of an integrated, commercial door and operator system that your workplace needs, Overhead Door™ products make operating your facility safer and easier. Our products are manufactured to give you durable, long-lasting performance for years of extended use and trouble-free operation. Each product, from residential to industrial to commercial applications, is backed by knowledgeable and professional customer support for troubleshooting and answers to your questions.
Though you can do some maintenance to your garage doors on your own, it may be a good idea to schedule routine inspections with a professional. A typical service call will include a manual inspection of the door and opener. Then adjustments can be made including spring tension, chain/belt tension, limits and force adjustments and door lubrication. Fees for this service vary from place to place, but garage door repairs typically cost between $147 and $340.
Whether you're planning on moving in the future or you're fixing up your forever home, replacing a garage door can provide an excellent return on investment and boost your home's resale value. According to Remodeling magazine's 2016 Cost vs. Value report, garage door upgrades provide a nationwide average return on investment of over 90%, making it one of the top five home improvement projects.
If your garage door's spring breaks, stops working properly, or snaps, you'll lose the ability to open and close your garage door. This could happen due to a variety of issues, like normal wear and tear or from extreme temperature changes in a short amount of time. Spring replacements require a quick response from a garage door provider near you. Contact The Home Depot and a local, background-checked technician will respond within 24 hours.

We specialize in all varieties of garage door repair work. We have the tools and knowledge to get the job done safely. It can be somewhat dangerous to take on a garage door repair on your own, and most garage door companies will advise against attempting a DIY fix. There are some hazards to watch out for when working around these heavy and high tension doors. We recommend you give the experts at Girard's a call to address the issue in a safe and timely manner.
Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.

Since 1975, Kitsap Garage door has provided Kitsap Penninsula with reliable, comprehensive and responsive residential and commercial garage door repair, maintenance and installation services. At Kitsap Garage Door, our primary focus is offering Bremerton, Shelton and Kitsap, WA, home and business owners with the highest quality products and services, as well as exceptional customer experiences marked with free service estimates, workmanship warranties, reliable support and emergency services.

At PK Garage Door, we firmly believe that an installation properly done is the key to a top-performing garage door system. Well-experienced, we understand and follow the highest safety standards in the industry. In addition, Garaga has certified our company as one of their Garaga Expert dealers, which means we meet their strict criteria for technical expertise and professionalism.    
Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.
Since 2015, we’ve tested a variety of devices such as smart locks, video doorbells, DIY home security systems, thermostats and more. We use these testing experiences to inform our evaluations of other equipment. As time and resources allow, we occasionally test new types of products, but there are still some circumstances where we’re unable to conduct in-house tests. When testing isn’t possible, we conduct thorough research using the same standards we apply to our in-house tests – this is the case with smart garage door openers. We’ve reviewed garage door openers since 2011. 
The salesman-disguised-as-technician trick: In this trick, you arrange for a service call to your home, perhaps paying a small fee up-front, and a neatly uniformed man arrives in a very technical-looking truck, carrying an impressive tool kit. He carefully examines your door, perhaps using some impressive testing devices to lend weight to his expertise. He then condemns your door as not worth repairing, and tells you, to his sincere regret, that you must have a new one. In fact, this technician is not a technician, but a salesman who only sells, and does not repair, doors. Even if he doesn't sell you, he is doing well just collecting fees for service calls that are no more than sales visits. He doesn't actually have to ever fix anything, and he may not even be capable of doing so himself. He's an expert at selling, which genuine technicians are not. In the worst case, when you refuse to buy a whole new door, he might refuse to follow up with a visit from an actual technician, either outright, or only with an unacceptable delay ("we're too busy to get a guy out until next week", when your car is trapped). If you find yourself closing in on this situation, then politely invite him to leave, and try someone else. That is your right, and in fact the only power you have to bargain in such circumstances. At that point, he may offer to promptly bring in his competent colleague, who will turn up lacking charm and looking awful, but might actually do the work, possibly at a fair price. If so, you will have beaten a legal variation of the classic illegal bait-and-switch (see below). The switch was attempted, but not required, which makes this legal. This is a hazard of any direct-sales situation. Because it rarely appears in everyday retail sales, it can surprise the unwary.
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
Loosening or tightening the set-screws is the moment of most risk, since the end-wrench is a potential missile if you slip, and your hand is close to the cone. When the wrench is removed and only the rods are in place, it would seem that the worst that could happen is that the rod is flung out and the captive spring and cone rattle around, assuming you are keeping yourself clear of the rod's radial disk of rotation, and not leaning on the rod such as to fall into the apparatus were the rod to slip out of your grasp. The torsion shaft design has the virtue of capturing the mass of the spring and cones reliably on the shaft, preventing these parts from launching themselves as projectiles, even in an accident.
Cycle lifetime unchanged by diameter-versus-length tradeoffs: Since the material stress (and thus cycle lifetime) for equal torques varies only with d, and not D or N, trading coil diameter (D) for spring length (N) in this fashion has no effect on cycle lifetime. Long and skinny, versus shorter and fatter, they'll wear the same if they have the same wire size and diameter-length product. The game of life is all about wire size when it comes to springs (see below).
When garage door repair isn’t an option — perhaps the current door is beyond fixing or you want to upgrade to a quieter, more energy-efficient model — it’s time to buy a new one. But choosing a garage door is not as simple as it sounds, even when you know the right size for your home. A wide range of materials, styles and finishes are available, and each factor influences the cost. Garage doors are made of aluminum, steel, vinyl, fiberglass, masonite, wood (typically cedar or mahogany), or a composite of several materials. They may be insulated against cold or heat. Traditional and modern styles include raised panel, carriage house or crossbuck. Most styles have window or arch options, and are available in different wood finishes and neutral colors. Because garage doors account for a large part of a home’s exterior, their appearance is usually a homeowner’s top priority. An attractive garage door can increase a home’s curb appeal and resale value.

End treatments: Torsion springs also are made in a variety of end treatments. The "standard torsion end" is most common, as is pictured in my examples, consisting simply of a short, straight length of wire projecting tangentially. Various non-standard end treatments have longer "ears", U-turns, ends bent in toward the center or along the axis, or even loops. Non-standard ends are used in end fasteners peculiar to various manufacturers, which would seem to serve mostly as a guarantee that you buy overpriced replacements from that one source.

Whether you are a new homeowner looking to personalize your home or you need to replace your existing garage door, Clopay® makes it easy to find the right choice for your home. Your garage door can account for up to 30% of your home’s façade, so choosing the right style can have a great impact on your curb appeal. Clopay doors are available in a variety of styles including carriage-house, raised-panel and modern, all with convenient overhead operation. Choose from a variety of colors, woodgrain finishes, materials and hardware to complement your home’s exterior.
×