Fiberglass and vinyl garage doors are composite units, combining a steel core behind a fiberglass or vinyl skin. They have also polyurethane insulated base sections, or other type of foam insulation. These premium doors can match steel garage doors, and be a realistic imitation of wood (namely fiberglass units), but they may be more expensive than steel units.
End treatments: Torsion springs also are made in a variety of end treatments. The "standard torsion end" is most common, as is pictured in my examples, consisting simply of a short, straight length of wire projecting tangentially. Various non-standard end treatments have longer "ears", U-turns, ends bent in toward the center or along the axis, or even loops. Non-standard ends are used in end fasteners peculiar to various manufacturers, which would seem to serve mostly as a guarantee that you buy overpriced replacements from that one source.
Wayne Dalton garage doors are some of the best in the industry. We offer a large selection of garage door designs in many colors and options that can drastically enhance your home’s curb appeal. Not only will a new garage door add beauty to your home, but replacing an old or outdated door with a new one can increase your home’s value. Did you know that year after year replacing the garage door is one of the top home improvement projects for return on investment? Purchasing a new garage door for your home is an excellent investment and we’ve made it even easier to find the perfect door with our Garage Door Design Center or Garage Door Selection Guide.
Many garage door opener remote controls use fixed-code encoding which use DIP switches or soldering to do the address pins coding process, and they usually use pt2262/pt2272 or compatible ICs. For these fixed-code garage door opener remotes, one can easily clone the existing remote using a self-learning remote control duplicator (copy remote) which can make a copy of the remote using face-to-face copying.
When you install a new garage door, replace all the hardware as well. If your automatic opener doesn’t have an automatic reversing system that includes photoelectric eyes, replace it. Doors with openers also require two extra pieces of hardware that you’ll see in Photo 4: a support strut (usually included in the door kit) and an opener bracket (not included). For doors with torsion springs located over the door, spend the $50 or so to have a garage door professional release the tension.
You’ll never have a difficult time reaching us here at Absolute Overhead Door. You will speak to another person 24/7 – never an answering machine or computer – no matter if you call day or night. Our team will always be ready to answer any questions that you may have and get a plan and schedule underway to fix everything from a broken spring, garage door opener, to a broken garage door that needs complete and new installation. If you need us to replace broken springs, you or your teenage driver backed into the garage door, or in the market for a new door install or upgrade, we’ve got you covered! We provide garage door service from 8am to 6pm – with no extra charge for evenings and Saturday’s. Absolute Overhead Door Service also provides 24-hour Emergency Service with minimal charge. We are your garage door repair and broken spring experts! If you have an unknown issue with your garage door or an issue with your garage door opener, give us a call today for guaranteed same day service. 
Openers are available with a chain drive, screw drive or belt drive. Chain drives (a long chain pulls the door open and closed) are the least expensive, but they’re loud. Screw drives (a long threaded rod drives a mechanism that opens and closes the door) are priced in the mid- range. They require the least maintenance, but they’re not as quiet as belt drives. Belt drives (a rubber belt opens and closes the door) are the quietest, making them the best choice if you have living space above the garage. They’re also the most expensive.

Regardless of the material, you will likely need to perform some regular maintenance tasks. A garage door professional can examine common problem areas to ensure all are working as they should. Additionally, it is necessary to examine the integrity of the door itself, since your garage can be especially vulnerable to security issues if your door is not structurally sound.
We guarantee same day garage door service on calls placed by 1:00 pm. We are on most jobs within 2 hours of the request for service being placed. All our technicians travel in fully stocked trucks to your home or business to enable us to complete nearly all overhead / garage door repairs on the first trip without the need for additional appointments just to complete the job. We guarantee to exceed the normal service appointment you have experienced with other garage door companies by implementing the Absolute 22-point inspection on all jobs that we take on. Our 22-point safety inspection ensures the customer that all vital mechanical and safety parts of the door are fully operational and functioning as they should be. This prevents any future service calls for our customer and in turn saves YOU, the customer, money!
If this manipulative, we-are-your-nanny business approach is truly in our best interests as consumers, then we shouldn't be allowed near ladders, lawn mowers, or power tools. Those products are just as hazardous and prone to misuse as torsion springs, yet no one thinks of them as forbidden. The only genuine difference is that torsion springs are a hazardous thing you need only rarely, while a lawn mower is a hazardous thing you need all the time.
Garage door openers are always a nice convenience, but become most appreciated when the weather turns nasty. They are also a near necessity if the task of opening and closing a garage door is too challenging, due to physical limitations. Most are relatively inexpensive and highly reliable, although unless you are very handy, you should probably budget for professional installation.

Dynamic Door Service can install a new garage door replacement for you quickly and efficiently, conducting thorough testing on your garage door replacement and automatic garage door opener to be sure both are functioning properly.  Investing in a garage door replacement also adds value to your home, since it is one of the best home remodelling projects to recoup cost when you sell your home. Whether you need a new automatic garage door, a garage door replacement, garage door repair or garage door opener replacement or repair, call Dynamic Door Service for prompt, professional automatic garage door installation, maintenance and service.


I was careful not to assume that the previous installation correctly oriented the right- and left-hand springs on the correct sides of the center bearing plate. They could have been installed backwards by an incompetent installer, resulting in them having been wound looser (larger diameter coil) instead of tighter (smaller diameter coil) than when in their relaxed state, and if so I would have corrected them on the new installation. The proper orientation of the springs applies their reaction torque from tighter winding such that it turns the drums to lift the door. Verifying this is a rather simple exercise in mechanical visualization, but does require some care to be certain of correctness. If you were to install the springs backwards, and then start to wind them in the wrong direction, then the torsion bar will start winding the drums backwards, and not holding against the vise pliers, which should be obvious to inspection. Winding a spring backwards also tends to screw the spring off the cones; this error cannot proceed too far before the spring slips off the cones.
Wood - Wood garage doors are sturdy and quite beautiful. However, if you live in a humid climate, your doors will be prone to rotting and splitting. If your wood is painted, you must also factor in the costs of painting as part of your regular maintenance routine. The cost of repairing the wood varies depending on the type. However, average cost to repair a wood panel is $190 to $215.

The Genie SilentMax 750 belt drive garage door opener isn't as feature-packed as the Chamberlain B970, but its value is hard to overlook. The 75-HPc motor isn't as strong as the B970s, but is still plenty strong for any residential use, and the opener is widely judged to be pleasingly quiet. Smart features are built in, too, but using those requires the addition of the optional Genie Aladdin Connect module (Est. $95). The biggest downside is that there's no battery back-up.

Openers are available with a chain drive, screw drive or belt drive. Chain drives (a long chain pulls the door open and closed) are the least expensive, but they’re loud. Screw drives (a long threaded rod drives a mechanism that opens and closes the door) are priced in the mid- range. They require the least maintenance, but they’re not as quiet as belt drives. Belt drives (a rubber belt opens and closes the door) are the quietest, making them the best choice if you have living space above the garage. They’re also the most expensive.


Mechanical garage door openers can pull or push a garage door with enough force to injure or kill people and pets if they become trapped. All modern openers are equipped with “force settings” that make the door reverse if it encounters too much resistance while closing or opening. Any garage door opener sold in the United States after 1992 requires safety eyes—sensors that prevent the door from closing if obstructed. Force settings should cause a door to stop or reverse on encountering more than approximately 20 lbs (9.07 kg) of resistance. Safety eyes should be installed a maximum of six inches above the ground. Many garage door injuries, and nearly all garage door related property damage, can be avoided by following these precautions.
Step 5: Check for loose hardware, and tighten as needed. On swing-up doors, check the plates where the spring is mounted to be sure the screws are tight, and tighten any loose screws. On roll-up doors, check the hinges that hold the sections of the door together; tighten any loose screws, and replace any damaged hinges. Sagging at one side of the door can often be corrected by servicing the hinges. If a screw hole is enlarged, replace the screw with a longer one of the same diameter, and use a hollow fiber plug, dipped in carpenters' glue, with the new screw. If the wood is cracked at a hinge, remove the hinge and fill the cracks and the screw holes with wood filler. Let the filler dry and then replace the hinge. If possible, move the hinge onto solid wood.
Here are the winding rods inserted in the winding cone of the unbroken old spring, posed just for a picture. Note that I have carefully placed a sturdy, steady ladder just clear of the swing of the rods, such that when I am standing on the lower rungs to reach the rods, that my head and body are clear of the "kill zone" around the spring and cone. You must have a trustworthy platform to stand on, because a slip or shake of the ladder while you are winding can cause you to lose your socketed attachment to the cone, letting loose the spring. I would not trust an ordinary household step ladder for this purpose.
Smart garage door openers aren't as expensive or hard to find as you might think. In fact, no matter what smart home platform you're using, there is an opener that will work for you. Smart garage door controllers add convenience like remote access, voice control, scheduling and vehicle detection to your garage door. You'll never need to wonder if you left it open ever again. 
​We know that your commercial ​door can take a beating. That's why we build quality, tough commercial doors to withstand the daily wear and tear of owning and operating a business. Engineered for excellence and backed by a dedicated nationwide network of Red Ribbon Distributors, Overhead Door™ commercial and industrial doors are the premier choice for durability, serviceability and hassle-free performance. ​​​​
The electric overhead garage door opener was invented by C.G. Johnson in 1926 in Hartford City, Indiana.[1] Electric Garage Door openers did not become popular until Era Meter Company of Chicago offered one after World War II where the overhead garage door could be opened via a key pad located on a post at the end of the driveway or a switch inside the garage.[2]

If your door feels heavy, it is likely that your springs have started to wear down and are no longer capable of bearing the weight that they once did. Now, don’t worry, just because a spring is starting to lose its strength doesn’t mean it will snap at any moment. However, simultaneously, a weak spring isn’t any safer to try and repair on your own.
The lucky-for-you-I-found-another-problem trick: Another trick is to suggest your automatic opener was damaged (or "compromised") by the additional load or shock presented by the failure of the spring(s). The plastic worm gear used in the most common openers (see above) wears normally over the years and tends to leave a lot of debris inside the opener housing. Removing the opener cover reveals a lot of plastic shavings that may be cited as "evidence" you need a new opener, when the gears are actually still serviceable. Nevertheless, you may have indeed worn out the gear if you repeatedly cycled the door with the opener despite having broken springs, which is possible if you have a very lightweight door.
Checking if the lift drums need resetting: The old position of the lift drums on the shaft may have slipped or otherwise lost the the proper position, requiring a reset of the drum position on the torsion shaft. You will also reset the drums if you are replacing the lift cables, since the new cables will not exactly match the length of the old ones. Problems like uneven tension on the cables, or a tilted door, or a door that doesn't easily stay aligned with the tracks, can be due to an improper "set" of the drums on the shaft. So one shouldn't assume the old positions are correct. Setting the drums on a "fresh" part of the shaft will avoid the possibility of damaging the shaft from retightening in the same dimples.
A rolling code is a protocol used by garage door openers to keep your door safe and secure. When the radio signals from your remote control are broadcast to your garage door opener, it uses a specific code to communicate. Older models used the same code every time, making garage door openers vulnerable to burglars using a radio frequency identifier device. 
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
If you have paired springs, you can take a shortcut here instead of using locking pliers. Simply apply a slight torsion to the bar by clamping one of the springs with an easy half-turn or so applied. This will hold the lift cables in slight tension while you wind the other spring. If you have a single spring design, you can't use this trick, and have to use the locking pliers.
The most common grade of torsion springs have an expected life of about 10,000 cycles. The hardened and tempered steel experiences tremendous forces each time the door opens or closes. Gradually, the steel fatigues with each flexure, and eventually cracks and breaks, usually releasing its stored energy in an instant with a horrific "sproing" noise or bang. If you average about two car trips per day, opening and closing the door a total of 4 times daily when you come and go, then that expected life becomes 2500 days, or only about 7 years. If you have an automatic opener, then if you're like me, you tend to cycle the door even more frequently, and can expect the need for spring replacement even sooner. Moreover, my three-car garage has three doors, so on average I can expect a repair job every few years. Over a lifetime, it is very economical to do these repairs myself.
Garage doors cause injury and property damage (including expensive damage to the door itself) in several different ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on extension spring systems).
Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.

The inside of the door panels bear a few dings, since filled with Bondo, from my teenage boys shooting hockey pucks. The streaks on the right that look like dinosaur claw scratches came from operating the door inadvertently when the rear doors of a van were open. The responsibility for these scars is all mine; they have also been Bondo-filled. We tend to use a lot of Bondo around our house. The crud on the walls and ceiling are cobwebs and dust infiltrates.
This is the electric opener which operates this door. I'm picturing it here because you pull the rope to disconnect the trolley, run the trolley under power to the fully-open position, and then disconnect power before working on the door. Then you should lock the door down with either the security lock or with Vise-Grips or C-clamps. This avoids the door lifting when you don't expect it as you are applying spring adjustments. It you were to foolishly overwind the spring without the door locked down, you could possibly find the door trying to leap up to the raised position when you aren't prepared. That would likely knock your grip off the winding rods, with potentially disastrous results. I like to work under the safety principle that serious accidents should be physically possible only when you make two or more stupid mistakes at the same time.
How many times a day do you open or close your garage door? You probably don’t even know because we take our garage door for granted until…. Until it doesn’t go up… until it doesn’t come down… until it gets noisy, difficult to open by hand or some other problem develops. You need help – and if you’re locked in or locked out, you need help in a hurry. You need A-Authentic Garage Doors. Here’s why:
When buying an opener, choose a 1/3 hp or 1/2 hp opener for a single garage door (1/3 hp can be hard to find at some home centers). Go with 1/2 hp for a double door and 3/4 hp for a door that has a wood or faux wood overlay (they can be heavy!). Openers have a set opening speed, so installing an opener with a higher horsepower won’t open your door any faster.
Absolute Overhead Door recently launched a blog that can be found here so that readers would be able to see the benefits of a garage and what they should do in the event their newly driving teenage drove into the garage door. The blog offers many tips for “fix at home” solutions as well as giving examples of situations when calling us for a service call is the best decision. In our blog, we give professional and honest recommendations for the most reader and budget friendly options for families looking for advice that doesnt cost a fortune and an obligation to purchase a new garage door from a salesman afterwards! Check it out! We hope you enjoy it.

The usually recommended rule for a door being properly balanced is that it should lift "easily" through all its travel. The door may also remain stationary if let go somewhere around the middle of the travel, but a smoothly rolling door many not show this behavior (while a sticky track will!), so easy travel is the only reliable test for proper balance. A difficult door may be due to stiff bearings or rollers in the mechanism, tracks out of alignment, etc., not necessarily the torsion spring adjustment.

As noted above, set-screw clamping may have distorted the cross-section of the shaft and made it difficult to slide off all the hardware. With the shaft on the floor, it may be possible to restore enough roundness to proceed, using compensating clamping force to the distorted area via a machinist's vise, an arbor press, a hydraulic shop press, etc., on the shaft body. Burrs and other slight distortions on the shaft can be filed off with a hand file or touched with an abrasive wheel on an angle grinder. At some point, the condition of the shaft may just be degraded enough that it ought to be replaced.
We also offer garage door opener repair service. Many times, what appears to be a problem with your garage door is actually a problem with your garage door opener. Our professional technicians have experience with all major garage door opener brands, including the popular LiftMaster line of garage door openers. Whether your garage door opener is making too much noise, failing to turn on, moving too slowly or not opening or closing your door properly, we can fix it fast.
Looking for something powerful but don’t want it to be too loud? This garage door opener from Chamberlain is a great option. Featuring an exclusive Motor Vibration Isolation System which eliminates vibration for reduced noise, this is a good choice especially you have an attached garage with rooms above the space. It also has MyQ enabled technology that allows you to monitor and control the opener via your smartphone with an extra purchase of the product. You can set the opener’s timer to close the door one, five or 10 minutes if you forget, and it has sensors to make sure it won’t close if something is in its path. It comes with a lifetime motor, lifetime belt, five-year parts, and one-year accessories warranty.
Thus it is humanly impossible to dodge a falling door. If the spring happens to break when the door is moving up or down somewhere in the middle of travel, as is more likely, then you'll have even less time. Hence it is not prudent to stand or walk beneath a moving garage door. Of course people often do, and the only reason this does not frequently kill people is that springs typically break at the bottom of travel, where they are stressed the most.
You might be thinking: Aha! Why don't we lift the door, clamp it in place, and install the springs while they are thus safely unwound, rather than deal with all that accumulation of hazardous torque? The answer: At the top-of-travel, the unwound springs are not fully relaxed; they are still clamped to the torsion shaft with a significant stretch along the shaft axis, plus about a half-turn to keep the door snug at the top. This extra length amounts to the stacking of extra turns that accumulate from winding, also termed "spring growth" in the business. In my case this is about 7 turns of 0.2253 wire, or about 2 inches. Stretching the spring that much and clamping it with a half-turn or so of twist is not feasible.
Looking for a distinctive overhead door? At PK Garage Door, we have the one to fit your specific needs. In the garage door industry for over 30 years, we know all their ins and outs. What sets us apart from our competition? Our personalized customer service! For us, every customer is unique, just like their needs. Because we work exclusively with top quality products, we carry Garaga as our garage door line. 

Because your garage door is a major entryway to your home, it is important to keep it in good working order for your own safety, security, and convenience. Choosing the right style and appropriate materials will lessen the amount of repairs that may arise. Additionally, investing in regular maintenance can be cost-effective in the long run. If your garage door is in need of major repair, it is best to call a professional garage door repair company for assistance. Typically, the company will charge for at least one hour for making a service call. However, the benefits of a professional repair job can well outweigh any costs, as a professional can ensure the safety, security, and proper operation of your garage door.
Regardless of the material, you will likely need to perform some regular maintenance tasks. A garage door professional can examine common problem areas to ensure all are working as they should. Additionally, it is necessary to examine the integrity of the door itself, since your garage can be especially vulnerable to security issues if your door is not structurally sound.
Ryan, the tech that did the initial inspection and Kyle, the tech that did the installation were both extremely skilled, knowledgeable, and have excellent customer service. They arrived on time as scheduled. Explained well what needs to be done and did the job well. We’re very pleased and recommend Castle Garage Doors. We’re giving Ryan, Kyle 10 🌟 along with Hollie for having excellent customer service in making sure the whole process ran smoothly. Thank you 👏🏻👏🏻👏🏻 -Grandpa & Grandma Read less
Typically, it will cost less to install a steel garage door without an opener than to install a custom wood door with a garage door opener. Recent innovations have also yielded high-tech doors with thick insulation and energy-efficient glaze, as well as finished interior surfaces and other significant upgrades. These are more expensive doors, but they are also extremely durable.

The best garage door openers can be controlled from a remote location through your phone. If you’ve ever left home and had a moment of panic, not knowing if you left the garage door open, this feature can give you peace of mind. The door opener’s built-in Wi-Fi connects directly with your home Wi-Fi router, which allows you to close your garage door from wherever you are through a MyQ smartphone app. The Chamberlain Group opener has this feature – it’s a 1-horsepower garage door opener with extra lifting power for unusually heavy doors of over 500 pounds.


Those who benefit from this anti-competitive behavior have many excuses for it. They claim that the product is too dangerous and infrequently needed for the public to purchase directly. They say the job is hazardous and requires techniques and tools with which the amateur will rarely practice, which is true. They write me in anger saying I don't understand how expensive it is to put a truck on the road with a technician and parts and salary and benefits and insurance and advertising and every other common business expense. They say it will take the homeowner hours of effort to do this safely and correctly, while they can do it in a fraction of that time and at a price that isn't worth the effort to save. But should they set themselves up as the judge of what you can and cannot do? Of what is an economical use of your time? Imposing minimum order quantities or charging retail prices for small orders is legitimate; inquiring into the purchaser's background is not.
Scott did an amazing job. Your customer service team is excellent. I emailed late on Thanksgiving night my request for service. Your team called my house within 30 minutes and set up an appointment for the following morning. Scott came out and was great. I had purchased the lifetime warranty package with Precision before, and your team delivered. I highly recommend anyone getting a repair to purchase the lifetime warranty package since your team stands behind your product. Rarely do I write reviews - but am happy to share great information on great companies. Thanks for the great service!

The Heavy Duty Chain Extension Kit for 8 The Heavy Duty Chain Extension Kit for 8 ft. High Garage Doors is required for reliable everyday operation of Chamberlain heavy duty chain drive models in 8 ft. garage door applications. Featuring a quick-install extension rail and replacement chain the kit includes everything needed for quick and easy installation. Includes ...  More + Product Details Close
aluminium frames B&D B and D doors and openers BnD Colorbond Custom garage doors cyclone Danmar Doors Garage door insulation garage door insurance garage door motors garage door remote garage door repairs garage door seals garage doors perth garage door springs and cables garage door struts insulated garage doors keyless entry Knotwood lifting cables Merlin garage door motors Merlin garage door openers Perth perth garage door repairs perth garage doors perth garage door servicing replacement remote reprogram garage door remote roller doors sectional garage doors Steel-Line tension springs tracks and rollers wind struts
The classic telephone bait-and-switch: This time-honored swindle, also called "false advertising", can show up in the garage door business. Here's how this scam works: When you call and say you have a broken spring, and ask for a repair price, you are told over the phone that the price is X dollars, which typically might seem a little better than the competition. When the repairman shows up, after looking at your broken door, he will casually and matter-of-factly tell you it will cost 2X. If they told you over the phone that it would cost X, well, that was only for one spring, and he must (he must, mind you) install not just one, but two. He will act surprised if you object, as if you should have known that from what you were told over the phone. If you expected to really pay just X, it was your fault for misunderstanding because you don't know anything about how garage doors should be repaired. (You will feel intimidated at this, since you honestly don't know anything, else why would you have called a repairman? Intimidation is a powerful tool against customer resistance.) If your door used only one spring to start with, he will insist on converting yours to two, telling you it is safer the next time a spring breaks. If you originally had two springs, he will tell you that he must replace both springs, and you must therefore pay double what was quoted. While it is true that converting or replacing both springs is a good idea, the bait-and-switch pricing is not. The "bait" is the low price quoted to you over the phone, which they never intended to honor, and the "switch" is switching the price to something higher on a pretense. This method of selling is literally criminal (for example, see Florida Statutes 817.44, all states have similar laws), but a service business can usually avoid detection or prosecution because there are no printed advertisements or other tangible evidence, just one-on-one phone calls. If you find yourself in the middle of this trap, then the proper response is to dismiss the repairman without paying a nickel. Don't expect that you will be able to negotiate a fair price with someone who is using criminal business methods. Certainly don't expect that he will accept a lower price because you accuse him of false advertising. If you absolutely cannot wait for another service call, then you'll have to accept the fraud, in which case you should do so quietly. People that use these methods typically have ways to mentally justify their behavior to themselves as a reasonable business practice, and won't react well to your suggesting otherwise, even though they are in fact small-time criminals, not shrewd businessmen.

I was careful not to assume that the previous installation correctly oriented the right- and left-hand springs on the correct sides of the center bearing plate. They could have been installed backwards by an incompetent installer, resulting in them having been wound looser (larger diameter coil) instead of tighter (smaller diameter coil) than when in their relaxed state, and if so I would have corrected them on the new installation. The proper orientation of the springs applies their reaction torque from tighter winding such that it turns the drums to lift the door. Verifying this is a rather simple exercise in mechanical visualization, but does require some care to be certain of correctness. If you were to install the springs backwards, and then start to wind them in the wrong direction, then the torsion bar will start winding the drums backwards, and not holding against the vise pliers, which should be obvious to inspection. Winding a spring backwards also tends to screw the spring off the cones; this error cannot proceed too far before the spring slips off the cones.


The best garage door openers have a lifetime warranty on their motor and belt or chain. While it’s common for motors to come with lifetime warranties, belt and chain and parts warranties are often not that generous. However, it’s not uncommon for parts warranties to extend several years. Often the warranties are limited and subject to specific stipulations that vary and are detailed in the user manuals.
With over 300 independently moving parts, your garage door is a deceptively complex piece of equipment. To help prevent malfunctions and break-downs, it is a good idea to occasionally perform a garage door tune-up to keep all of these parts in good working order. A regular tune-up service by a Sears professional can prevent unexpected door problems and prolong the life of your existing equipment.

Garage Door Repair Company

×