My garage door broke on a Saturday night as I was getting ready to leave for a holiday party. Kelvin was here within 30 minutes. He reviewed everything with me that was happening with my door. He gave me the estimates of what was immediately needed to be done in order for my door to raise and then what I will need to have done very soon. I could see all the problems he pointed out to me and I decided to have everything done. He completed everything that night. I was very satisfied with Kelvin’s professionalism and the work he did. Thank you again.
Resetting the drums, if needed: If the drums were incorrectly set in their old positions, one must reset both drums in new positions on the shaft. This is complicated by the presence of old dimples in the torsion shaft from previous setting(s), which must be avoided lest they improperly influence the new setting of the drums. To begin this process of resetting the drums, the door must first be lowered and resting level on the floor, the spring(s) must be in the unwound condition with their set-screws loosened, and the lift cables wrapped around the drums. If for some reason the door does not rest level on the floor, such as the floor being uneven, then insert temporary shims between the door bottom and the floor to bring the door up to level. Loosen the set-screws on the drums, and turn the torsion shaft to avoid the old dimples from the set-screws in the old drum position. Tighten the set-screw on the left drum (that is, on your left as you face the door from in the garage), creating a new dimple, and apply tension to its cable with the locking-pliers technique, enough tension to keep the cable taut but not enough to start to move the door up. Attach and wind the cable on the opposite (right) drum by hand until the cable is similarly taut, and set the screw, remembering that tightening the screw will tend to add a bit of extra tension to the cable. Both drums should now be fixed on the torsion shaft, with the cables about equally taut (listen to the sound when you pluck them like a guitar string) and the door still level on the ground. Setting the left drum first, and the right drum second, will allow you to take up any slack in the cable introduced by the left drum rotating slightly with respect to the torsion shaft as you tighten the set screws. This alignment and balance of the cables, drums, and door is critical to smooth operation and proper closing. If you have a single-spring assembly, the distance along the torsion tube from the spring cone to one drum is longer than to the other drum, which allows a bit more twist to one side than the other, and you may have to compensate with the setting of the drums.
Spending your whole weekend setting up a new garage door opener is not on the top of most peoples list. This opener is easy to install for most levels of DIYers and it provides a quiet and reliable open and close. This has 3/4 HPc DC chain features and the powerhead can open 12" in a second. It has a wireless remote and Intellicode 2 security to prevent people from breaking into your home.
Looking for a distinctive overhead door? At PK Garage Door, we have the one to fit your specific needs. In the garage door industry for over 30 years, we know all their ins and outs. What sets us apart from our competition? Our personalized customer service! For us, every customer is unique, just like their needs. Because we work exclusively with top quality products, we carry Garaga as our garage door line.
Annual maintenance. Make an annual check of all nuts and bolts on rails and rollers to make sure they’re firmly tightened. Check the condition of all cables to make sure they’re not worn or frayed. Lubricate rollers and springs with a garage-door lubricant (see How to Fix a Noisy Garage Door for maintenance and problem-solving tips). The door should operate smoothly and be properly balanced. Check the balance by disconnecting the opener and lowering the door halfway- the door should hold its position. If it doesn’t, adjust the spring tension or replace the springs.
I was careful not to assume that the previous installation correctly oriented the right- and left-hand springs on the correct sides of the center bearing plate. They could have been installed backwards by an incompetent installer, resulting in them having been wound looser (larger diameter coil) instead of tighter (smaller diameter coil) than when in their relaxed state, and if so I would have corrected them on the new installation. The proper orientation of the springs applies their reaction torque from tighter winding such that it turns the drums to lift the door. Verifying this is a rather simple exercise in mechanical visualization, but does require some care to be certain of correctness. If you were to install the springs backwards, and then start to wind them in the wrong direction, then the torsion bar will start winding the drums backwards, and not holding against the vise pliers, which should be obvious to inspection. Winding a spring backwards also tends to screw the spring off the cones; this error cannot proceed too far before the spring slips off the cones.
Called for an appointment and was surprised that I could have a tech come the same day. Matt arrived ahead of schedule, inspected the garage door and gave me a tune up to get things working properly again. He explained what would need to be done in the future, and the cost. I will certainly call them when the time comes to get that work done.read more
Single panel doors are constructed from one monolithic panel. From the closed position a single panel door swings up and overhead with a hinge on each side (known as jamb type hardware) to the fully open position. A disadvantage of monolithic panel doors is that the swing up arc of the door occurs partially outside the garage. This means a vehicle must stop and park several feet in front of the door to avoid being hit by the garage door when it is opened.
Precision Garage Door of Seattle is the best choice if you are looking for garage door repair, maintenance, replacement and installation in the greater Seattle area. Our vast experience sets us apart from other competitors. Our experienced garage door specialists and our approach to finding and treating the cause of the problem is why we are the trusted name for garage doors in Seattle.
Once the springs are relaxed and loose on the torsion shaft, the lift drums lose their tension on the lift cable, and the cable comes loose. The end of the cable is terminated by a press sleeve, which locks into a ramp on the drum. Different drum styles have a bolt or other method to fix the cable end to the drum. These steel cables are springy and won't stay in place without tension. If my pre-inspection had showed that these cables were worn or frayed, then I would have ordered proper replacements ahead of time from the spring distributor, since this is the opportunity to replace them. Standard hardware-store cable and fittings are not appropriate.
A typical version of an overhead garage door used in the past would have been built as a one-piece panel. The panel was mounted on each side with unequal parallelogram style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers. The weight of the door may be 400 lb (181.4 kg) or more, but is balanced by either a torsion spring system or a pair of extension springs. A remote controlled motorized mechanism for opening garage doors adds convenience, safety, and security.
We’ve earned that reputation by always putting our customers first. When it comes to residential and commercial garage door repair services in northern Kentucky and Cincinnati, you’ll always get our best. That includes reliable installation, quick and responsible customer service, free and fair estimates on our work and 24/7 emergency service when you need it the most. We have designed our installation and repair services to make sure you get the most out of your garage door for as long as possible.
Through our garage door configurator by Clopay, you can design, visualize and purchase a new Clopay garage door. Upload a photo of your home and then browse the configurator to see which style works for you. Choose from a variety of designs, textures, colors, finishes, window options and decorative hardware. You’re able to easily and quickly see the transformation, and then make it a reality.
We install, service and repair all kinds and types of garage doors in the Lehigh Valley. We carry high-quality products from the top garage door brands around. Whether you need a garage door replacement or a routine annual inspection of your garage door components, we are confident that we will be able to get the job done quickly and efficiently. We even offer emergency services open 24 hours a day, 7 days a week in order to ensure that all of your garage needs are attended to.
Lift cable placement: On the standard residential door mechanism, the loops at the lower ends of the two lift cables loop over the two bottom roller shafts which project from the bottom bracket on the door. The upper cable ends fasten to the drums using one of the methods described above. The drums are positioned along the torsion shaft such that the inner edge of each drum is approximately over the edge of the door. The cable winds onto the drum from outside in, so at the top of travel the cable is winding onto the inner edge of the drum, vertical from the edge of the door where it is looped over the roller shaft. As the door is lowered, the cable winds out to the outer edge of the drum, and thus is a bit out from the vertical, but the cable still falls in the gap between the guide rails and door edge. My cables rub and slap on the rails a bit, but after 30 years and many 10,000s of cycles, they don't seem to have worn at all.
This work is risky, but the risk is comparable to doing your own car repairs, or climbing on the roof of your house to clean your gutters. These are dangerous things that many people can do safely, but that safety depends on intelligent understanding and application of proper techniques. Professional door repair technicians, who are fully knowledgable, skilled, and experienced, report that they nevertheless are injured from time to time, despite their best efforts. Coldly evaluate your abilities and motivations, to judge whether you can manage the risks of this work for the benefit of the money and time you might save.
The Certified Technician, Rey Lopez, was competent, professional, polite, and willing to work. He quickly removed the old door and installed the new one. He then explained the vast differences between what we originally had and what we'd just purchased (stronger spring/tension rates; increased viability of door opening/closing life; beefier hardware; plastic vs. nylon rollers; stronger door reinforcement). Ray performed with alacrity his tasks and then demonstrated the quiet, solid way the door retracted--no banging after the initial rise from the ground. Finally, his attention to detail was so precise that he enabled another remote controlling all three doors, plus he capped some frayed wires, thus solving the problem of why the door opened intermittently. I would rate him a "6" on a scale of "1-5", meaning he went above and beyond our expectations. His "can do" attitude, coupled with the deference he showed, will take him a long, long way. May HaShem richly bless him in his endeavors!read more
If you’re looking for a stylish garage door that is a statement of your good taste, we have customized solutions that fit your family’s lifestyle. Or if it’s the safety and security of an integrated, commercial door and operator system that your workplace needs, Overhead Door™ products make operating your facility safer and easier. Our products are manufactured to give you durable, long-lasting performance for years of extended use and trouble-free operation. Each product, from residential to industrial to commercial applications, is backed by knowledgeable and professional customer support for troubleshooting and answers to your questions.
Cycle lifetime unchanged by diameter-versus-length tradeoffs: Since the material stress (and thus cycle lifetime) for equal torques varies only with d, and not D or N, trading coil diameter (D) for spring length (N) in this fashion has no effect on cycle lifetime. Long and skinny, versus shorter and fatter, they'll wear the same if they have the same wire size and diameter-length product. The game of life is all about wire size when it comes to springs (see below).
The majority of those who have purchased this product have been happy with it, saying it’s extremely quiet and comes with a great lifetime warranty. Some of the more critical reviews had to do with the remote not working well and other minor malfunctions. (A few quick tips can help you fix any common garage door opener problems.) However, most were satisfied with the product and would recommend it to others.