My garage door broke on a Saturday night as I was getting ready to leave for a holiday party. Kelvin was here within 30 minutes. He reviewed everything with me that was happening with my door. He gave me the estimates of what was immediately needed to be done in order for my door to raise and then what I will need to have done very soon. I could see all the problems he pointed out to me and I decided to have everything done. He completed everything that night. I was very satisfied with Kelvin’s professionalism and the work he did. Thank you again.
In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the project yourself, but you should recruit help for removing the old door.
Prices, like the garage doors themselves, run the gamut. You can pay as little as $400 for a door that you install yourself, or several thousand dollars for a high-end premium door that includes all the bells and whistles, including installation. A mid-range, 16-by-7-foot door will typically cost from $750 to $1,500, installed. Premium insulated steel doors run from $750 to $3,500. According to Remodeling Magazine’s 2017 Cost vs. Value report, the average national cost of a garage door replacement is $3,304.
Direct Drive - Unlike chain- and belt-driven systems, where the motor remains stationary while moving a chain, a direct drive motor moves while the chain stays in place. Because of this, the only moving part is the gear the motor uses to move while lifting the door. To our knowledge, only one company makes direct drive garage door openers: Sommer. The company claims the motors are more efficient and quieter than any other type of opener. However, this is the most expensive type of opener we’ve found, costing around $286 on average.
While winding or unwinding, one must be mindful of the possibility that the spring could break during winding process itself. If that should happen while the spring is significantly torqued, hazardous forces on the winding bar will suddenly become unbalanced, and the bar will take an unexpected jump, possibly injuring your hand or anything else in its path. At the same time, the spring remnants, although captured on the torsion bar, will create a frightening racket that would give the bravest soul a start. So your winding technique should be firmly in control of the rods, and you should not be so delicately perched on a ladder such that a startle will result in a fall.
When your garage door starts acting up, more often than not it is telling you it's time to do a bit of maintenance. So, before hitting the panic button, try these simple repairs. First, examine the rollers and tracks. If you can't remember the last time you cleaned them (and they look the part!), give them a good brushing and then add some lubricant. Next, perform these simple garage door maintenance tasks.
I was careful not to assume that the previous installation correctly oriented the right- and left-hand springs on the correct sides of the center bearing plate. They could have been installed backwards by an incompetent installer, resulting in them having been wound looser (larger diameter coil) instead of tighter (smaller diameter coil) than when in their relaxed state, and if so I would have corrected them on the new installation. The proper orientation of the springs applies their reaction torque from tighter winding such that it turns the drums to lift the door. Verifying this is a rather simple exercise in mechanical visualization, but does require some care to be certain of correctness. If you were to install the springs backwards, and then start to wind them in the wrong direction, then the torsion bar will start winding the drums backwards, and not holding against the vise pliers, which should be obvious to inspection. Winding a spring backwards also tends to screw the spring off the cones; this error cannot proceed too far before the spring slips off the cones.
Our value pick is the Chamberlain PD76EV. It costs about $50 less than our top pick, but it has most of the higher-priced model’s advantages. The PD76EV has the same lift capacity, horsepower, lift system and automation compatibility. However, it doesn’t come with advanced features such as a backup power source, close timer and keyless entry pad. If you can live without those, this opener is a great choice.
If your door has two springs, most professionals and research online says that replacing both springs is the best option. Most torsion springs are rated for 10,000 close/open cycles. If only one of your springs is broken, both springs are still recommended to be replaced. Considering that your second spring will break soon anyways, this added on fix is only going to cost you about $50 extra to assure that you don't have to pay another service fee for a second visit.
Trading diameter for length: Observe that in the spring rate formula in the table above, factors D (diameter of coils) and N (number of coils) appear together in the denominator of the spring rate formula. Algebraically, given equal wire sizes, this means that the product of the coil diameter and overall length produces the spring torque, not the diameter or length alone. Physically, this means that you can trade off torsion spring coil diameter versus overall length in inverse proportions to maintain the same torque rate. Trade-off example: A spring with 2-inch diameter coils that is 36 inches long equals a 1.5-inch diameter spring that is 48 inches long, because the product in both cases is 72 (inches squared). This assumes that wire size is equal in the trade-off, and that you have not counted dead coils in the length. Service technicians use this principle to make quick substitutions for what's on their truck versus what you need. But if you understand this, you're ahead of many technicians who don't know this trick. Maybe now you can educate the next one you hire.
Most wood doors are sectional roll-up doors, though a swing-up wood door that’s meant to be painted can be affordably built in the driveway from a wood framework and plywood. Custom wood doors are typically made of durable softwoods such as Douglas fir, cedar, redwood or cypress, or from hardwoods such as oak or mahogany. Appearance-grade hardwoods are relatively expensive.
Ryan came to my rescue within 6 hrs of my call. He was professional, knowledgeable, friendly, and very thorough. He got my door up and running after figuring out what 3 others could not! Don’t try and go the cheapest route like I did because you’ll end up wasting time and money. Hire the pros like Ryan FIRST! If I ever need someone in the future, I’ll be calling them first thing! HIGHLY RECOMMENDread more
Garage doors cause injury and property damage (including expensive damage to the door itself) in several different ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on extension spring systems).
Once the shaft, springs, and center bearing plate come down and lay on the floor, the old springs should be easy to get off and new ones slid on and assembled. Two bolts hold the center cones to the center bearing plate. The bearing on the center plate can be oiled while it is exposed from having the springs off. At this point it is a relief to be working with inert parts while standing on the floor rather than energized parts while up on the ladder. You might think it would save a little time to replace the spring with the shaft left up on the wall, but I found it was easier and safer to lower the works down to the garage floor first.
We install, service and repair all kinds and types of garage doors in the Lehigh Valley. We carry high-quality products from the top garage door brands around. Whether you need a garage door replacement or a routine annual inspection of your garage door components, we are confident that we will be able to get the job done quickly and efficiently. We even offer emergency services open 24 hours a day, 7 days a week in order to ensure that all of your garage needs are attended to.
We want to serve you not only today, but also in the years ahead. To do that, we make sure that we provide prompt, professional, well-trained technicians that efficiently get the job done right the first time. We take pride in doing everything possible to eliminate warranty issues and to ensure that our clients are thoroughly pleased and return to us for all garage door needs.
We have everything needed and the expertise required to make accurate repairs for every variety of garage door. Whether you have a steel, wooden, or composite garage door, one of our team members will be happy to help you diagnose the problem and then apply an effective solution. Our repair services include repairs for springs, cables, rollers, tracks, sections, and more! Is your door noisy? We know the right way to fix it! Call us any timeyou need us to fix a problem.
You might genuinely need some extra parts when you thought you simply needed a broken spring replaced, and a good serviceman will perform a simple inspection to identify such parts. Nor is it unreasonable for a business to charge separately for a service call versus repair work actually performed. But the best protection for you as a buyer, being somewhat at the mercy of whomever you decide to bring on site, is to understand what is being done, and ask intelligently for a clear explanation or demonstration of why extra parts are required.