Had a quick response to my call. thought I might have to wait a couple of days to coordinate their schedule and mine. To my surprise I received service in one and one half hours. Not only that but there was no sales call, technician Mike was fully prepared to give me a quote and complete the work as his vehicle carried everything needed. He very efficiently completed the work and cleaned up after I selected from the options. He replaced the springs all rollers and made needed adjustments expeditiously. I would recommend this firm to anyone needing garage door repairs.read more
We install, service and repair all kinds and types of garage doors in the Lehigh Valley. We carry high-quality products from the top garage door brands around. Whether you need a garage door replacement or a routine annual inspection of your garage door components, we are confident that we will be able to get the job done quickly and efficiently. We even offer emergency services open 24 hours a day, 7 days a week in order to ensure that all of your garage needs are attended to.
Insulation, which increases energy efficiency and can help to lower utility bills, is crucial when a garage door is attached to the home. In this case, doors with high R-values are preferred. This means it has insulation that can keep the heat in. The higher the R-value, the better insulated your garage will be against outside noise and cold and hot air.

Measure springs only when relaxed: Measurements must be taken on a relaxed spring because the winding adds significant overall length while reducing the coiled diameter. If you have a paired design, and one is broken and one is intact, then don't try to measure the length of the intact spring with the door down. A wound spring has 7 or 8 turns adding to the overall length, and will therefore be about 2 inches longer than when relaxed. Measure the lengths of the pieces of the broken spring, which will be unwound, and add them together. As a check, one can measure the length of the intact spring after it is unwound in the procedure to follow below. Be sure also to observe whether the springs are originally of equal sizes, because it is quite possible that they are not.
Add the fact that a front-facing garage door can eat up almost 20% of your home’s front facade. With that much curb appeal at stake, a worn-out, beat-up garage door can be a real liability. No wonder that a big majority of homeowners responding to the “Report” gave a garage door replacement project a Joy Score of 9.4 — a rating based on those who said they were happy or satisfied with their remodeling, with 10 being the highest rating and 1 the lowest.
The standard winding tools are simply a pair of 18-inch lengths of mild steel rod, 1/2-inch diameter. Winding cones can have different socket sizes (such as 5/8 inch instead of 1/2 inch), so it is important to measure the socket and select a matching rod diameter. Also beware that poor-quality cones may have a sloppy fit to the winding bars, and a loose fit presents a severe hazard of slipping at the worst moment; anything more than about an inch or two of play at the handle end is too loose for safety. I bought a 3-foot length of zinc-plated 1/2-inch diameter steel rod from Home Depot for about $3, which conveniently cuts into two halves of just the right length (the store might even cut it for you if you ask). A steel supplier selling at commodity prices might charge about 50 cents or so for such a piece that weighs about 2 lbs. Drill rod would work if used in the annealed condition in which it is originally sold, but the added expense provides no benefit and the brittleness (if it had been hardened and not annealed) would worry me a bit. Rebar, threaded rod, screwdrivers, etc., are absolutely foolish as they will not fit the socket snugly. Aluminum rod is definitely too weak, and will bend under the torque that must be applied. Longer rods would make for more leverage but unwieldly swing; shorter rods make for uncontrollable swing. As we'll calculate below, the 18-inch standard tool length is an appropriate compromise. Note that you do not need 18 inches of ceiling clearance above the torsion shaft to use an 18-inch rod, since you need not swing the rods above horizontal when winding.
A standard residential door raises 7.5 feet, but since the door goes horizontal this is equivalent to raising the whole door for half that distance, or about 3.75 feet. So if the door weighs, say, 150 lbs, then the energy supplied by the springs is 3.75 * 150, or about 563 foot-pounds. This is like throwing a 50-lb sack of cement up a 11-foot flight of stairs. Or catching a 50-lb sack of cement dropped from 11 feet up.
It's a great idea to hire a professional to do your garage door opener installation for a few reasons. First of all, a pro can often be the most time-efficient way to handle the garage door opener installation, because a pro will have the right tools and experience to make your garage door opener installation as swift and smooth as possible. Secondly, a pro garage door opener installation will include making sure all the required garage door opener mounts and sensors are put together properly. A great garage door opener installation will include using the manufacturer’s recommended method of assembly and optimal placement of the garage door opener mount and sensors. Find top-notch garage door opener installation pros on Amazon Home Services and you'll see professional garage door opener installation services at competitive prices. Secure convenience and peace of mind by getting a professional garage door opener installation for your home. You'll never regret adding a garage door opener installation project to your to-do list. If you’re the kind of person who doesn’t have the time or patience to do your garage door opener installation, don’t worry. Because you don’t have to if you don’t want to. Amazon Home Services has you covered, to do your garage door opener installation quickly and professionally. Just schedule the garage door opener installation pro of your choice from our list of top-rated service providers.
It you have a tilt-up door, you are looking at a $150 - $200 repair or replacement. If it's a roll-up door it's going to cost you more. Roll-up door spring repair or replacement is usually around $200 - $250 for a 2 car door. If the brackets need to be disassembled to remove the springs due to the shaft not sliding sideways enough it will cost you an additional $50 - $100. 

Your garage door is most likely the largest opening on your home, and as a result, it can affect your home’s energy efficiency. For homes in areas that experience colder winters or warmer summers, choosing an insulated door can save you money and improve the comfort of your home. Doors insulated with our Intellicore® insulation technology operate more quietly and are more durable. We also offer insulated glass window options that can help maintain energy efficiency and allow natural light into your garage. Visit our insulation guide to learn more about garage door insulation, or learn more about Intellicore® here.

We also offer garage door opener repair service. Many times, what appears to be a problem with your garage door is actually a problem with your garage door opener. Our professional technicians have experience with all major garage door opener brands, including the popular LiftMaster line of garage door openers. Whether your garage door opener is making too much noise, failing to turn on, moving too slowly or not opening or closing your door properly, we can fix it fast.
The Keychain Garage Door Remote offers portable control The Keychain Garage Door Remote offers portable control with the highest level of security. Featuring a three-button design this compact remote controls up to three garage door openers individually. Easily programmed and compatible with nearly every garage door opener made by Chamberlain LiftMaster and Craftsman it’s the easy option for ...  More + Product Details Close
Every thing the tech demostrated was helpful, he knew how to do his job even if his eyes were shut. Very knowledgeable, took time out to explain every detail about the install process. Very highly satisfied. A d would love to have him for future additional repairs. Would definitely recommend sears and would use you guys again thanks mr.technician for a job well done.
Follow the manufacturer’s instructions to assemble the opener and mount the rail to the header bracket above the door. Then set the opener on a ladder where you’re going to install it. The ladder (usually an 8-footer) holds the opener in position while you measure for your lengths of angle iron. If necessary, put boards under the opener to raise it.

GUESS YOU DON’T CARE to reply to my emails, so I'm posting it up here..... On Sep 8, 2018, at 2:52 PM, Joe Turiczek wrote: Thanks for the invoice, thanks for the service, thanks for the rapid response, thanks for Chris (the tech), but one note….. I’m a really handy guy, I repair and maintain nearly everything around the house, I am very mechanically adept, and I am also a highly skilled technical person that runs my own business by trade. I would have and could have repaired the belt myself, but I am traveling for business sooner than I could have ordered a belt, and did the repair….which means, I looked at the belts, I watched all the videos, it’s an EASY repair. I have belts down to a science, I’m really not an armchair DIY repair guy, I’m pretty good……That being said, I also shopped for prices of new belts for at least 30 mins or better, across easily 20-30 different parts and/or repair websites. Why am I telling you this? Because I think Chris, and your labor prices are spot on, and he deserved every cent, and your labor billing is more than fair…..however, I think your charge for the belt is a bunch of crap, it is nearly double of the HIGHEST price I found, which was $20-$25 higher than the average prices I found. Based on that alone, there is no way I could recommend, your otherwise FANTASTIC service, to anybody I know with a straight face. That’s just me being honest, because that’s who I am.
Looking for something powerful but don’t want it to be too loud? This garage door opener from Chamberlain is a great option. Featuring an exclusive Motor Vibration Isolation System which eliminates vibration for reduced noise, this is a good choice especially you have an attached garage with rooms above the space. It also has MyQ enabled technology that allows you to monitor and control the opener via your smartphone with an extra purchase of the product. You can set the opener’s timer to close the door one, five or 10 minutes if you forget, and it has sensors to make sure it won’t close if something is in its path. It comes with a lifetime motor, lifetime belt, five-year parts, and one-year accessories warranty.

Whether you're planning on moving in the future or you're fixing up your forever home, replacing a garage door can provide an excellent return on investment and boost your home's resale value. According to Remodeling magazine's 2016 Cost vs. Value report, garage door upgrades provide a nationwide average return on investment of over 90%, making it one of the top five home improvement projects.
Ryan came to my rescue within 6 hrs of my call. He was professional, knowledgeable, friendly, and very thorough. He got my door up and running after figuring out what 3 others could not! Don’t try and go the cheapest route like I did because you’ll end up wasting time and money. Hire the pros like Ryan FIRST! If I ever need someone in the future, I’ll be calling them first thing! HIGHLY RECOMMENDread more
If return on investment is a priority and you don’t live in the West, your best strategy may be to buy a low- to moderately-priced door that significantly improves the look of your home. Consider adding an automatic garage door opener at the same time. The beauty of a new door and the convenience of an automatic opener are sure to be a winning combination.
The usually recommended rule for a door being properly balanced is that it should lift "easily" through all its travel. The door may also remain stationary if let go somewhere around the middle of the travel, but a smoothly rolling door many not show this behavior (while a sticky track will!), so easy travel is the only reliable test for proper balance. A difficult door may be due to stiff bearings or rollers in the mechanism, tracks out of alignment, etc., not necessarily the torsion spring adjustment.
While a sudden issue is usually easily repaired, a consistent issue that has gone unaddressed for months or years will likely require a total replacement. The problem is that garage doors have a number of heavy, powerful moving parts. If the door is working as it is designed, it can open and close hundreds and hundreds of times without issues. However, if there is even a small issue in the lifting mechanism that repeatedly influences the movement of the door, you will soon find that the damage caused over those hundreds of lifts can’t be fixed.
Typically, it will cost less to install a steel garage door without an opener than to install a custom wood door with a garage door opener. Recent innovations have also yielded high-tech doors with thick insulation and energy-efficient glaze, as well as finished interior surfaces and other significant upgrades. These are more expensive doors, but they are also extremely durable.

Whether you are a new homeowner looking to personalize your home or you need to replace your existing garage door, Clopay® makes it easy to find the right choice for your home. Your garage door can account for up to 30% of your home’s façade, so choosing the right style can have a great impact on your curb appeal. Clopay doors are available in a variety of styles including carriage-house, raised-panel and modern, all with convenient overhead operation. Choose from a variety of colors, woodgrain finishes, materials and hardware to complement your home’s exterior.
Recently another type of opener, known as the jackshaft opener, has become more popular. This style of opener was used frequently on commercial doors but in recent years has been adapted for residential use. This style of opener consists of a motor that attaches to the side of the torsion rod and moves the door up and down by simply spinning the rod. These openers need a few extra components to function safely for residential use. These include a cable tension monitor, to detect when a cable is broken, and a separate locking mechanism to lock the door when it is fully closed. These have the advantage that they free up ceiling space that an ordinary opener and rail would occupy. These also have the disadvantage that the door must have a torsion rod to attach the motor to.
One of these "sproing" events at our house finally motivated me to research how these repairs are done. This happened in 2002, when my wife parked the chariot and shut the door. After the door closed, there was a horrific noise that she could only astutely describe as, "a big spring snapping and vibrating". Although I have hired professionals several times in the past to install or repair garage doors, the difference this time was the innovation of Google and newsgroups like alt.home.repair. I was determined to learn the process and to search for online parts vendors.

Insulation increases the efficiency of your door and can lower your electric will. You need R-value garage doors. These type of doors keep out hot and cold air and also provide a sound barrier between the outside and your garage. Insulated doors use polyurethane or polystyrene foam as insulation inside the door. More information about garage door replacement cost.
The standard winding tools are simply a pair of 18-inch lengths of mild steel rod, 1/2-inch diameter. Winding cones can have different socket sizes (such as 5/8 inch instead of 1/2 inch), so it is important to measure the socket and select a matching rod diameter. Also beware that poor-quality cones may have a sloppy fit to the winding bars, and a loose fit presents a severe hazard of slipping at the worst moment; anything more than about an inch or two of play at the handle end is too loose for safety. I bought a 3-foot length of zinc-plated 1/2-inch diameter steel rod from Home Depot for about $3, which conveniently cuts into two halves of just the right length (the store might even cut it for you if you ask). A steel supplier selling at commodity prices might charge about 50 cents or so for such a piece that weighs about 2 lbs. Drill rod would work if used in the annealed condition in which it is originally sold, but the added expense provides no benefit and the brittleness (if it had been hardened and not annealed) would worry me a bit. Rebar, threaded rod, screwdrivers, etc., are absolutely foolish as they will not fit the socket snugly. Aluminum rod is definitely too weak, and will bend under the torque that must be applied. Longer rods would make for more leverage but unwieldly swing; shorter rods make for uncontrollable swing. As we'll calculate below, the 18-inch standard tool length is an appropriate compromise. Note that you do not need 18 inches of ceiling clearance above the torsion shaft to use an 18-inch rod, since you need not swing the rods above horizontal when winding.

Current data from real estate firms throughout the country show that replacing the garage door raises the value of a home by an average of $2,810, according to Remodeling Magazine's report. Based on the average cost of $3,304, this means that replacing a garage door is expected to return 85 percent of the job’s cost, nationally. When replacing a garage door in the Western U.S., however, the return is predicted to be 110.8 percent of your investment.
Most wood doors are sectional roll-up doors, though a swing-up wood door that’s meant to be painted can be affordably built in the driveway from a wood framework and plywood. Custom wood doors are typically made of durable softwoods such as Douglas fir, cedar, redwood or cypress, or from hardwoods such as oak or mahogany. Appearance-grade hardwoods are relatively expensive.
Insist on having any old parts returned to you, and have that noted on the written order before work begins. An honest and competent technician will not object to this. The evidence will establish whether you really needed the parts or not, and you can consult another opinion if you have any doubts. This tends to deter the parts-upsell scam, and protects you even if you know nothing about what you're buying while under the pressure of making a costly decision. If the old parts mysteriously "disappear", then you have reason to be suspicious.
Speed of a falling door:: Physics tells us that the transit time of a free-falling body is sqrt(2x/g), where x is the length of the fall and g is the acceleration due to gravity (32.2 ft/sec^2). If this typical 150 lb door were to fall an equivalent of 3.75 feet, this falling time would be sqrt(2*3.75/32.2) = 0.48 seconds (480 milliseconds). The terminal velocity is gt, or 0.48 seconds * 32.2 ft/sec^2 = 15.5 ft/sec = 10.6 mph.

If you have paired springs, you can take a shortcut here instead of using locking pliers. Simply apply a slight torsion to the bar by clamping one of the springs with an easy half-turn or so applied. This will hold the lift cables in slight tension while you wind the other spring. If you have a single spring design, you can't use this trick, and have to use the locking pliers.


Our team of 100-plus technicians and service representatives takes care of you every step along the way. Our technicians are the best in the area. They’ll provide expert guidance as you consider your options, and then top-notch service to complete the repairs. When you want Cincinnati or Northern Kentucky garage door repair you can trust, choose AE Door & Window.
If you’re replacing an existing garage door opener in your home, the simplest method for finding the right horsepower is to check the rating of the unit in your garage and get something with equal or higher power. Most homes have single- and double-car sectional garage doors made of aluminum or steel, which is the most affordable type of garage door. These doors are relatively light, so a motor with rating of 1/2 horsepower is more than sufficient. While 1/3 horsepower motors are available, they can wear out faster than those with 1/2 horsepower in such settings, so it’s a good idea to invest a little extra for a more capable garage door opener.
Now 13 pounds of force must be respected when backed by many hundreds of foot-pounds of stored energy, waiting to be released. Holding this torque is equivalent to stalling a 3 horsepower DC motor. But holding and turning these handles does not require extraordinary human strength. Note that this maximum tangential force depends only on the weight of the door, and the radius of the drums, and is divided by the number of springs (some designs have only one longer spring, as mine did originally, instead of two shorter ones). Higher or lower lift distances imply more or less turns to wind the spring (and thus a different spring geometry), but not more force on each turn.
Our technicians are specially trained to handle a variety of garage brands, styles, and configurations. After arriving at your home, a Sears technician will diagnose the problem and walk you through the options for fixing it. Next, the technician will make any necessary adjustments or replace broken parts to ensure the door can be operational once again. We always attempt to complete repairs the same day of service, and your satisfaction is guaranteed. Our representatives are standing by for your call and are happy discuss pricing options.

Most electric garage door openers have two lights: one in front of the opener and one behind or sometimes they sit side by side. They should provide enough light for you to get into your home from your car. Generally, people don’t leave the garage light on when it’s not in use, so it’s nice to have a temporary light when you arrive home. The length of time the light stays on varies according to how it is programmed. In most instances, you don’t need more than a few minutes from the time you leave the car to when you enter your home.
Sterling Door is the only company we trust with our garage door. When our old door acted up, springs, track, etc., they were always timely and got the job done. Then when we made the jump to a new door, they were excellent. They helped us choose the right door, not just pushing the most expensive model. And installation was well done. I recommend Sterling Door for all of your garage door needs.
Finally, we also carry any and every residential garage door product that you need to have a state-of-the-art, secure and safe garage door. We are proud certified dealers of Clopay doors, the most durable and versatile doors on the market. With over fifty years of garage door manufacturing experience, you can trust Clopay quality, just as you can trust our team to install these highest-quality doors.

Most styles, whether traditional or contemporary, feature panels, trim, and other detailing. Doors with true frame-and-panel construction tend to be sturdier than those with decorative detail that is merely glued or nailed on. Many styles have glass panels on the top row, which looks inviting from the street and brings daylight inside. You can also find roll-up doors with shatterproof glass or frosted plastic in all the panels, for a more modern look.


Most garage door openers are pretty expensive. So if you need an opener on a budget, the Genie 1035-V (also known as the Genie Chain Drive 500) gives you that desirable low price point. It doesn't have a lot of high-end tech features, nor will it manage heavy garage doors, but it does the basic work of raising and lowering the garage door perfectly well.
Screw - Screw-driven lift systems attach a long screw to the motor to move the garage door. These systems are powerful, fast, relatively quiet and require less maintenance than typical chain- or belt-driven systems. Genie and Overhead Door are two popular brands that make screw-driven systems. Based on our research of Genie’s line, you can expect to pay $244 on average for a screw-driven garage door opener.
The gentleman who showed up to my door was kind and very respectful. Introduced himself < Jeremy> and very professionally. He did an outstanding job and took time to let me know each step that was needed. Personally I would give Precision and the gentleman who came a big rating of a 10++++++ Thank you Precision and I would recommend your company to anyone.. A very pleased customer ... ..
I was having an issue with my garage door that turned out to simply be the remote lockout being accidentally engaged. I called Aaron’s Garage Door Service and rather than sending a tech out and charging me for such a simple problem, they explained the solution over the phone. I really appreciate businesses with a sense of integrity like that! If I ever have a real garage door problem, I will absolutely be calling these guys!
Our value pick is the Chamberlain PD76EV. It costs about $50 less than our top pick, but it has most of the higher-priced model’s advantages. The PD76EV has the same lift capacity, horsepower, lift system and automation compatibility. However, it doesn’t come with advanced features such as a backup power source, close timer and keyless entry pad. If you can live without those, this opener is a great choice.

While a new coat of paint can go a long way in improving the look of your garage door, the truth is that door design has come a long way in the years since garages were first installed in homes. Not only are newer doors more in line with current fashion trends, but they are also better sized for today’s cars. A new, contemporary door is a great way to get an immediate boost on the value of your home.
Cable fail-safe redundancy: Based on the proper setting of the drums on the torsion shaft, the two lift cables divide the lifting force equally to keep the door level as it rises. This not only levels the door, but also provides a fail-safe mechanism. If one of the cables should fail, such as from breaking or losing its end attachment, the other cable will then carry the full weight of the door. This will pull the door up on one side with twice the normal force, while the other side falls from its now unsupported weight, tending to make the door bind in its tracks and jam. Although not foolproof, this is a safety feature of the design which keeps the door from falling catastrophically if a cable were to fail while the door was traveling. The jammed condition also prevents a lowered door from opening with the hazard of a single broken cable, further minimizing the chances of both cables failing. Since if one cable fails the other must sustain the full weight of the door, the cables and attachments are rated many times the normal working load of half the door weight. A proper safety inspection of the door should include a critical look at the cables and their attachments.

Wood garage door: There’s no substitute for the distinctive look of wood. It’s typically made of moisture-resistant cedar, redwood or cypress and offers the most flexibility for custom designs. Depending on climate and exposure, wood doors require more maintenance. The average cost for a 16-by-7 double door made of quality wood: $1,200 to more than $4,000.


Screw-drive garage door openers are another type of direct-drive garage door opener. The screw-drive's relatively simple mechanism, which moves up and down a threaded steel rod, makes for a powerful, low-maintenance garage door opener. They are quieter than chain-drive openers, and are fast workers, but, like direct-drive openers, they tend to be pricey.
The typical electric garage door opener consists of a power unit that contains the electric motor. The power unit attaches to a track. A trolley connected to an arm that attaches to the top of the garage door slides back and forth on the track, thus opening and closing the garage door. The trolley is pulled along the track by a chain, belt, or screw that turns when the motor is operated. A quick-release mechanism is attached to the trolley to allow the garage door to be disconnected from the opener for manual operation during a power failure or in case of emergency. Limit switches on the power unit control the distance the garage door opens and closes once the motor receives a signal from the remote control or wall push button to operate the door.[3]

Capable of lifting a seven-foot garage door up to 500 pounds in weight, the SilentMax 750 comes with a number of convenience features for automatic and remote use. The included wireless keypad and dual remote controls will ​insure that you are the only one that has access to the door. Compatible with a number of in-car remote systems like HomeLink, you can also keep the remotes at home if you are worried about losing the “keys.”​


I mentioned earlier that this apparatus had at least one prior spring replacement, with a single longer spring having been replaced by two shorter springs. The clamping of the original spring had pressed dimples and an eccentric distortion into the hollow shaft. While this distortion was large enough to block the old cones from sliding across, I was able to remove the old hardware by just sliding them in the other direction. I did not have to bother trying to press out this distortion, since I could just work around it.
The various increments of standard wire sizes differ by only about 0.010 inch, so calipers or a micrometer would be the tool to use to be certain of the stepped size you have, or else a trustworthy ruler marked in tenths of an inch to use the measure-10-turns-and-divide-by-10 trick. The most common wire sizes in the US are 0.207", 0.218", 0.225", 0.234", 0.243", 0.250", and 0.262".

One can overwind the springs slightly, up to about 8 turns on a standard residential door (that is, 1/2 or 3/4 extra turns), to compensate for undersized or fatigued springs, or increased door weight from painting or humidity, but this results in more stress on the springs and therefore decreased lifetime. If the door is too heavy for that slight tweak, then different springs are needed.


Most doors come with electric door openers. After a while these openers malfunction and need to be replaced. If your opener is broken, you're in luck. These repairs don't cost very much and can be replaced easily. You might even be able to do it yourself. Learn how to replace your garage door opener in 15 minutes https://www.youtube.com/watch?v=HeaR6Yhx6IY.

In the market for overhead garage doors? Browse our selection of Pella garage doors. You'll find many options for single garage doors, double garage doors, insulated garage doors and even roll up garage doors. Lowe’s also carries garage door screens—great for those who love to spend hours in the garage, but don’t want to deal with the bugs and pests that invite themselves in. We also carry garage door hardware, garage door springs, garage door decorative hardware and garage door sensors, and don’t forget to ask about our garage door installation and garage door opener installation. Once you've decided a garage door fits your home, you'll need to find the garage door opener that works best for you. At Lowe’s, we carry Genie garage door openers, Chamberlain garage door openers and SOMMER garage door openers that will work seamlessly with your garage doors. We now offer a garage door opener that's compatible with your Iris home automation system, too. Whether you prefer opening your garage with a garage door remote or garage door keypad, you'll find it at Lowe’s. Our selection of garage remotes includes everything from universal garage door remotes to specific brands like Chamberlain garage door opener remotes and Chamberlain garage door keypads. We also carry backup batteries, nylon garage door rollers, garage door parts, garage door opener parts and rail extensions to make sure your garage door is in good working order. Plus, we even offer garage door installations services, which include garage door spring repair and replacements, and garage door cable repair and replacements. We can also replace your garage door weather seal, also known as garage door threshold seals, and install a new garage door opener battery.
×