Torsion springs are devices that lift most of the weight of a garage door so that the door can be opened manually or by an electric opener. The torsion principle is applied via an efficient and economical apparatus consisting of a torsion shaft under spring torsion, which turns lift drums, which wind cables attached to the door near the bottom. All of this apparatus is mounted over the top of the door. The energy stored is sufficient, in an uncontrolled release, to break things, hurt you, or perhaps even kill you. The same could be said of jacking up your car to change a tire, or mowing your lawn, or raising children, so it is not crazy to want to do this yourself.


Angle iron provides a stronger installation and reduces vibration, which helps extend the opener’s life span. In an unfinished garage, attach the angle iron directly to the face of a joist with 1-in. lag screws. For finished ceilings, attach angle iron along the bottom of a joist with 3-in. lag screws. Hang the opener using two more lengths of angle iron and nuts and bolts. Use lock washers or thread-locking adhesive to keep vibration from loosening the nuts.

Dynamic Door Service can install a new garage door replacement for you quickly and efficiently, conducting thorough testing on your garage door replacement and automatic garage door opener to be sure both are functioning properly.  Investing in a garage door replacement also adds value to your home, since it is one of the best home remodelling projects to recoup cost when you sell your home. Whether you need a new automatic garage door, a garage door replacement, garage door repair or garage door opener replacement or repair, call Dynamic Door Service for prompt, professional automatic garage door installation, maintenance and service.
Next, the torsion shaft is reassembled with the new springs, the drums repositioned loosely on the shaft, this whole assembly slid back into the end bearings, and the drum set-screws tightened down. I tightened the set-screws about 1/2 or 3/4 of a turn after contact with the shaft, which provides a good grip, but does not distort the shaft. The drums can be set on their old positions, if they were correctly installed, which is snug up against the end bearings to remove any longitudinal play in the torsion shaft. Now the lift cable can be reattached to the drums, and a slight temporary torque applied to the shaft to keep the cable taut while the first spring is wound. This temporary torque is conveniently applied with a pair of locking pliers clamped on the shaft, positioned such that they hold the torque by pressing lightly against the wall above the door, before you start the spring winding, The locking pliers stay on the torsion shaft until you have finished the spring winding locked down the spring cone(s) with the setscrew(s), and removed the winding bars. Then you simply remove them with the release on the wrench handle. I feel that any job that doesn't require a trick manipulation with either locking pliers or duct tape (or in the ultimate case, both!) is just too boring. My trusty pliers look a trifle rusty ever since I used them to clamp something on my outdoor TV antenna "temporarily" and left them out in the weather for, oh, several years. The white stuff on the drum is paint overspray from the original painting of the garage interior.
Great!  We specialize in all sorts of garage door repair work.  Working around the garage door can be fairly dangerous if you’re trying to repair this issue on your own.  Most garage door companies will quickly remind folks about this, and it’s true.  Their are some hazards to watch out for when working around these heavy and high tension doors.  We recommend you give an expert a call to address the issue in a safe and timely manner for you.
One might stack lumber or arrange some other low platform for a steady footing, instead of the ladder. The aluminum ladder shown here is the splendid 16-foot Krause Multimatic, which carries a Type 1A Industrial rating (300 pound working load); I highly recommend it. However, product liability apparently forced this company into bankruptcy in September 2000 and the company ceased operations in June 2001; see http://www.krauseladders.com (this Web site went dead sometime in mid-2002). The world is a dangerous place.

Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.

Angle iron provides a stronger installation and reduces vibration, which helps extend the opener’s life span. In an unfinished garage, attach the angle iron directly to the face of a joist with 1-in. lag screws. For finished ceilings, attach angle iron along the bottom of a joist with 3-in. lag screws. Hang the opener using two more lengths of angle iron and nuts and bolts. Use lock washers or thread-locking adhesive to keep vibration from loosening the nuts.

If your garage door is opening slowly or making a lot of noise, the problem may not be your opener. So before you buy a new one, check for broken or wobbly rollers and brackets. But don’t replace the bottom roller bracket yourself—the cable attached to it is under extreme tension. You’ll need to call a pro. If you’re replacing the rollers, get nylon rollers. They operate quieter than steel rollers and cost only a few bucks more. Next, check the torsion spring (mounted on the header above the door opening) to see if it’s broken. When one breaks, you’ll see a gap in the coils. You’ll need a pro to replace a broken spring.

Garage Door Repair Co

×