If you have paired springs, you can take a shortcut here instead of using locking pliers. Simply apply a slight torsion to the bar by clamping one of the springs with an easy half-turn or so applied. This will hold the lift cables in slight tension while you wind the other spring. If you have a single spring design, you can't use this trick, and have to use the locking pliers.
The most common grade of torsion springs have an expected life of about 10,000 cycles. The hardened and tempered steel experiences tremendous forces each time the door opens or closes. Gradually, the steel fatigues with each flexure, and eventually cracks and breaks, usually releasing its stored energy in an instant with a horrific "sproing" noise or bang. If you average about two car trips per day, opening and closing the door a total of 4 times daily when you come and go, then that expected life becomes 2500 days, or only about 7 years. If you have an automatic opener, then if you're like me, you tend to cycle the door even more frequently, and can expect the need for spring replacement even sooner. Moreover, my three-car garage has three doors, so on average I can expect a repair job every few years. Over a lifetime, it is very economical to do these repairs myself.

The disaster-is-nigh technique: As he inspects your door, the serviceman grimly calls your attention to "cracks" in your garage door. These appear very faintly in the middle of the door where the panels bow under their own weight when the door is up. This is normal, but the type of thing you wouldn't casually observe yourself. This surprising revelation disarms you, and you may find yourself strangely susceptible to the pitch for an entire new door.
The standard winding tools are simply a pair of 18-inch lengths of mild steel rod, 1/2-inch diameter. Winding cones can have different socket sizes (such as 5/8 inch instead of 1/2 inch), so it is important to measure the socket and select a matching rod diameter. Also beware that poor-quality cones may have a sloppy fit to the winding bars, and a loose fit presents a severe hazard of slipping at the worst moment; anything more than about an inch or two of play at the handle end is too loose for safety. I bought a 3-foot length of zinc-plated 1/2-inch diameter steel rod from Home Depot for about $3, which conveniently cuts into two halves of just the right length (the store might even cut it for you if you ask). A steel supplier selling at commodity prices might charge about 50 cents or so for such a piece that weighs about 2 lbs. Drill rod would work if used in the annealed condition in which it is originally sold, but the added expense provides no benefit and the brittleness (if it had been hardened and not annealed) would worry me a bit. Rebar, threaded rod, screwdrivers, etc., are absolutely foolish as they will not fit the socket snugly. Aluminum rod is definitely too weak, and will bend under the torque that must be applied. Longer rods would make for more leverage but unwieldly swing; shorter rods make for uncontrollable swing. As we'll calculate below, the 18-inch standard tool length is an appropriate compromise. Note that you do not need 18 inches of ceiling clearance above the torsion shaft to use an 18-inch rod, since you need not swing the rods above horizontal when winding.
If you’re looking for a stylish garage door that is a statement of your good taste, we have customized solutions that fit your family’s lifestyle. Or if it’s the safety and security of an integrated, commercial door and operator system that your workplace needs, Overhead Door™ products make operating your facility safer and easier. Our products are manufactured to give you durable, long-lasting performance for years of extended use and trouble-free operation. Each product, from residential to industrial to commercial applications, is backed by knowledgeable and professional customer support for troubleshooting and answers to your questions.
If you've researched this subject at all, you will no doubt have heard that you shouldn't be attempting torsion spring replacement as a do-it-yourselfer. That is generally good advice, so if you have any doubts about your abilities to do risky physical work on your own, hire the job out like everyone else. I found I was capable of doing this work with acceptable risk, because I intelligently understood the techniques, paid careful attention to methods and safety, knew how to use common tools in good condition, properly improvised the special tools I didn't have, and diligently attended to correctly performing a few moments of hazardous manipulation. I learned to do it purely on my own based mostly on bits of advice reluctantly given in Internet forums such as the Usenet newsgroup alt.home.repair. When I first wrote this page in 2002, there was no other do-it-yourself information available on the Web, and it was not until 2005 that reliable information disclosing the techniques started to appear elsewhere (see links below).
Though you can do some maintenance to your garage doors on your own, it may be a good idea to schedule routine inspections with a professional. A typical service call will include a manual inspection of the door and opener. Then adjustments can be made including spring tension, chain/belt tension, limits and force adjustments and door lubrication. Fees for this service vary from place to place, but garage door repairs typically cost between $147 and $340.

Are you needing garage door repair? Has your garage door opener stopped working, or are you looking to boost your curb appeal? Whatever your garage door need may be, your local authorized Overhead Door™ Distributor is there to assist. You can find the nearest Overhead Door™ Distributor near you today by using our Distributor Locator​ to search your area. ​​
Ryan Fleming, Technician with Precision Door replaced a broken garage door spring at our home last night and I was so impressed with his knowledge, professionalism and positive attitude that I felt compelled to write this review. We have been customers of Precision Door for over 5 years and have always been pleased with how promptly and cost effectively they perform repair and maintenance work. I highly recommend both Ryan and Precision Door.read more
Carter door: Garage doors in Florida come with extra bracing on the back and are wind-loaded to protect against hurricanes. The average with is 350 lbs. but some can weigh as much as 800 lbs. It can cost up to $1,000 dollars to replace a steel two-car garage door and if it's made of wood it can cost you up to $5,000 dollars. Some customized doors can be as much as 20 - 30k.
Leveling the door: Before commencing the spring winding, to check that you have the door properly leveled on the cables, considering all the factors above that make this a tricky adjustment, apply the winding cone setscrew lightly to lock the (unwound) spring cone temporarily on the torsion shaft, and momentarily lift the door slightly off the floor. Adjust the drum set as needed to level the door, repeating this slight lift test. Loosen the cone setscrew before winding the spring(s).
In 1921, C.G Johnson invented the upward-acting garage door and revolutionized the way the world entered their homes. For more than 97 years, Overhead Door™ garage doors have been securing and providing families access to their homes. Overhead Door™ garage doors are assembled in the United States and sold at over 450 authorized Ribbon Distributors throughout North America. The Overhead Door™ brand and Overhead Door™ distributors are synonymous with quality and dependability. To ensure you are getting the genuine, the original, make sure to always look for the Red Ribbon.

The Lifestyle garage door screen is a fully retractable garage screen door that works with your existing garage door. The Lifestyle features an industry first, fully retractable passage door for ease of entry and exit without having to retract the entire system. The Lifestyle garage screen is fully spring loaded, making opening and closing quick and easy.

Additionally, the B970 includes encryption features that prevent others from hacking the system to gain entry to your garage. Expert reviewers like this garage door opener a lot. The Tool Spy says the Chamberlain B970 justifies its higher price point by delivering excellent build quality and anti-vibration features. Consumer Search and Garage How To also approve of this unit.


Sterling Door is the only company we trust with our garage door. When our old door acted up, springs, track, etc., they were always timely and got the job done. Then when we made the jump to a new door, they were excellent. They helped us choose the right door, not just pushing the most expensive model. And installation was well done. I recommend Sterling Door for all of your garage door needs.
I think garage doors always show their age, there's no "timeless" garage door in my opinion. Walk passed a bunch of houses on your block, bet you could guess the time frame each one was installed based on the style of the door. Good thing is that garage door styles will only look dated after 15-20 yrs and even after that, they still look fine as long as they are well kept. I say go with what you love!

Recently another type of opener, known as the jackshaft opener, has become more popular. This style of opener was used frequently on commercial doors but in recent years has been adapted for residential use. This style of opener consists of a motor that attaches to the side of the torsion rod and moves the door up and down by simply spinning the rod. These openers need a few extra components to function safely for residential use. These include a cable tension monitor, to detect when a cable is broken, and a separate locking mechanism to lock the door when it is fully closed. These have the advantage that they free up ceiling space that an ordinary opener and rail would occupy. These also have the disadvantage that the door must have a torsion rod to attach the motor to.

Sterling Door is the only company we trust with our garage door. When our old door acted up, springs, track, etc., they were always timely and got the job done. Then when we made the jump to a new door, they were excellent. They helped us choose the right door, not just pushing the most expensive model. And installation was well done. I recommend Sterling Door for all of your garage door needs.
Current data from real estate firms throughout the country show that replacing the garage door raises the value of a home by an average of $2,810, according to Remodeling Magazine's report. Based on the average cost of $3,304, this means that replacing a garage door is expected to return 85 percent of the job’s cost, nationally. When replacing a garage door in the Western U.S., however, the return is predicted to be 110.8 percent of your investment.
Extremely straightforward and efficient estimating and installation process. We purchased a Clopay sectional steel garage door for our double garage that works flawlessly with our existing door operator. The guys suggested an insulated door, but I thanked them and said no because I don't care for the garage to warm up in the winter and create a corrosive atmosphere of melting snow and salt. Great job!
Absolute Overhead Door Service was founded by Vince Heuser when he saw the need for a new garage door company that performed at a much higher standard than most companies in the local area. He understood and saw that the need for HONEST, knowledgeable, dependable, and friendly technicians was apparent and Absolute Overhead Door Service was then founded in 2007. With our extraordinary growth because of our outstanding service, we cover the entire Central Kentucky area including Louisville, Elizabethtown, Bardstown, and Southern Indiana. We have warehouses strategically located so our technicians can be on your job within two hours on most days with no extra charges anywhere or anytime in normal hours. No other local company provides the convenient service hours that we do, 8am-6pm Monday-Saturday and Emergency Service after 6pm, Monday thru Friday, and on Sunday’s. We guarantee same day service on calls by 1pm and still get most service calls up to 4pm the same day.

The wire size and winding direction are easily discovered and proved, as I will explain below. You absolutely must know and understand the critical measurements of your old springs to order replacements. This assumes that the old springs were the correct to begin with; it is not uncommon to have incorrectly sized springs on a door due to a previous sloppy installation, or a significant change in weight of the door.
There’s another reason new doors are superior to old ones: energy efficiency. Keep in mind, garage doors are large, and when they open, they let a lot of outside air into your home. While you may have significant insulation separating your garage from the rest of your home, eventually that temperature differential will start to influence your energy bills.
You might genuinely need some extra parts when you thought you simply needed a broken spring replaced, and a good serviceman will perform a simple inspection to identify such parts. Nor is it unreasonable for a business to charge separately for a service call versus repair work actually performed. But the best protection for you as a buyer, being somewhat at the mercy of whomever you decide to bring on site, is to understand what is being done, and ask intelligently for a clear explanation or demonstration of why extra parts are required. 

Garage Door Opener

×