Although the door weight and drum size determine the maximum torque (termed MIP, maximum inch-pounds) needed from the fully-wound spring(s), the spring selection for a given door can still be varied to adjust the cycling stresses. A heavier wire on a larger diameter or longer length will produce the same torque as a lighter wire on a smaller diameter or shorter length, while undergoing less stress and therefore increasing expected cycle lifetime. The heavier spring will cost more but last longer, so this is another design trade-off. Calculating these spring sizes in the field is done using a book of tables (or the software equivalent) that we cannot provide here, although you will find the formulas to estimate spring properties below. If you can accurately provide the weight of the door, or the size(s) of the old spring(s) (assuming they were well-matched to balance the door), then a spring dealer should be able to tell you which spring sizes will work for you.


Most garage door openers are pretty expensive. So if you need an opener on a budget, the Genie 1035-V (also known as the Genie Chain Drive 500) gives you that desirable low price point. It doesn't have a lot of high-end tech features, nor will it manage heavy garage doors, but it does the basic work of raising and lowering the garage door perfectly well.
The Keychain Garage Door Remote offers portable control The Keychain Garage Door Remote offers portable control with the highest level of security. Featuring a three-button design this compact remote controls up to three garage door openers individually. Easily programmed and compatible with nearly every garage door opener made by Chamberlain LiftMaster and Craftsman it’s the easy option for ...  More + Product Details Close
And for some extra features, you'll appreciate accessing the system through the MyQ smartphone app. You can set up this Chamberlain opener to automatically close the door after 1, 5, or 10 minutes, which is great for people who are a bit forgetful. We also really like the motion-detecting control panel, which turns on lights whenever it records nearby movement.
When it comes to installing garage doors and openers, The Home Depot has an unbeatable team of professionals dedicated to making sure your garage door project runs smoothly from start to finish. Your new garage door can be customized with a variety of features like unique color choices, window styles and hardware upgrades. We also offer options for your garage door opener including Smartphone control, Wi-Fi, battery back-up. The Home Depot installs garage doors and garage door openers with extended warranties that go beyond industry standards. Contact us today for a free in-home consultation.
Location, climate and building codes are just a few factors to consider when determining which type of garage door is right for your home. Depending on the region you live in, you may need to choose a wind load option for your garage door. Wind loaded garage doors help safeguard your home in high wind prone areas. With garage doors serving as the largest and often times the primary entrance to the home, an insulated garage door may also be right for you.
The second stage of the wireless garage door opener system solved the opening-the-neighbor's-garage-door problem. The remote controls on these systems transmitted a digital code, and the receiver in the garage responded only to that code. The codes were typically set by eight to twelve DIP switches on the receiver and transmitter, so they allowed for 28 = 256 to 212 = 4,096 different codes. As long as neighbors used different codes, they would not open each other's garage doors. The intent of these systems was to avoid interference with nearby garage doors; the systems were not designed with security in mind. Intruders were able to defeat the security of these systems and gain entry to the garage and the house. The number of codes was small enough that even an unsophisticated intruder with a compatible remote control transmitter could just start transmitting all possible codes until he found one that opened the door. More sophisticated intruders could acquire a black box master key that automatically transmitted every possible code in a short time. An even more sophisticated method is known as a replay attack. The attacker would use a code grabber, which has a receiver that captures the remote's digital code and can retransmit that digital code at a later time. The attacker with a code grabber would wait nearby for the homeowner to use his remote, capture the code, and then replay the code to open the door when the homeowner was gone. Multicode openers became unpopular in areas where security was important, but due to their ease of programming, such openers are often used to operate such things as the gates in gated apartment complexes.
Thank you for visiting Precision Garage Door Service of Seattle. We specialize in the repair of residential garage doors, openers, sales, service, & installation. Where ever you live along the Wasatch front, You have my personal guarantee that your experience with us will be professionally handled from start to finish. Your service will be provided by qualified & certified technicians that have completed the most extensive & rigorous training in the industry. We are proud of our environmentally sensitive business practices. Please give us a call to discuss your specific needs. We look forward to serving you.
Garage door openers are always a nice convenience, but become most appreciated when the weather turns nasty. They are also a near necessity if the task of opening and closing a garage door is too challenging, due to physical limitations. Most are relatively inexpensive and highly reliable, although unless you are very handy, you should probably budget for professional installation.
Follow the manufacturer’s instructions to assemble the opener and mount the rail to the header bracket above the door. Then set the opener on a ladder where you’re going to install it. The ladder (usually an 8-footer) holds the opener in position while you measure for your lengths of angle iron. If necessary, put boards under the opener to raise it.
We specialize in all varieties of garage door repair work. We have the tools and knowledge to get the job done safely. It can be somewhat dangerous to take on a garage door repair on your own, and most garage door companies will advise against attempting a DIY fix. There are some hazards to watch out for when working around these heavy and high tension doors. We recommend you give the experts at Girard's a call to address the issue in a safe and timely manner.
Even if one could somehow stretch and clamp the springs to the proper extra length, the process would still be more trouble, and there would be little or no reduction of risk. Lifting the full weight of the unsprung door by hand and clamping it in the raised position is dangerous in itself, and creates the same amount of stored energy as winding the springs, ready to slip out of your hands. Many doors won't travel far enough up the track to provide clearance to access the springs. You're also going to have to deal with winding stiff steel cables onto both lift drums at once without any resistance to maintain tension. Finally, even if you managed to complete the installation with the door raised, you then have to lower the massive door against an untested balancing torque. If you've made a mistake, then that massive door has nothing but your skeletal force applied through your meat clamps (hands) to prevent it from falling down and crushing whatever is in the way (perhaps your feet?).
Removing winding cones from an old broken spring for reuse in a new spring: Springs without the winding cones installed are a little cheaper than with the cones. Twisting the old cones into a new spring is easy with a vise and pipe wrench, but it can be tricky removing old cones from a broken spring for reuse. To remove old cones, mount the cone in a vise such that the spring portion is free. Grab the last few turns of the spring in a pipe wrench, engaging the teeth of the wrench into the end of the spring wire. Turn the wrench against the end of the spring wire, releasing the end of the spring from its clamping onto the cone, as you twist the loosened spring off the cone. Another more certain if not brutal method is to use an angle grinder with a thin metal-cutting disk to cut through the loops of spring wire where the loops wrap around the cones, being careful not to nick the cone itself too much. You could also cut into the old spring loops with a just hacksaw and break off the loops with hand tools, but this will require a lot of effort.

Measure springs only when relaxed: Measurements must be taken on a relaxed spring because the winding adds significant overall length while reducing the coiled diameter. If you have a paired design, and one is broken and one is intact, then don't try to measure the length of the intact spring with the door down. A wound spring has 7 or 8 turns adding to the overall length, and will therefore be about 2 inches longer than when relaxed. Measure the lengths of the pieces of the broken spring, which will be unwound, and add them together. As a check, one can measure the length of the intact spring after it is unwound in the procedure to follow below. Be sure also to observe whether the springs are originally of equal sizes, because it is quite possible that they are not.
Nate was very polite and knowledgeable about our garage door dilemma. He was prompt and earlier than the appointed time. He phoned ahead to alert us of his approximate arrival. He assessed the situation and gave us options to choose from. He educated us about our type of garage door and the opener that is typically used with it. He basically did an overall replacement of all moving parts, (spring, cables, bearings etc..). He made sure that the opener wasn’t damaged in any way from the broken spring on the garage door. He was finished within the hour. Everything works great and we are now able to get our vehicles out. When the spring breaks on your garage door, there is no way you can lift this door. It was a little expensive but at least we didn’t have to buy an entire door assembly.read more
First and foremost, a garage door, by design, contains springs designed to balance your door and make it easier to lift. Those springs are under incredible amounts of tension. If a spring breaks or is improperly released, it can cause incredible and potentially fatal injuries. Keep in mind, when working on a garage door spring, it is likely that your face and head will be close to it, meaning that your most sensitive area will be in the direct path of the released spring.
Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.

Horsepower You’ll also want to consider the horsepower of your opener. Typically, 1/2 horsepower will work for most doors in newer homes. If you have a heavier solid wood door, though, you may want to opt for 3/4 horsepower so it can lift it with ease. You can also get 1 and 1 1/2 horsepower models, but those are a better fit for commercial or special situations.


Scott did an amazing job. Your customer service team is excellent. I emailed late on Thanksgiving night my request for service. Your team called my house within 30 minutes and set up an appointment for the following morning. Scott came out and was great. I had purchased the lifetime warranty package with Precision before, and your team delivered. I highly recommend anyone getting a repair to purchase the lifetime warranty package since your team stands behind your product. Rarely do I write reviews - but am happy to share great information on great companies. Thanks for the great service!
The disaster-is-nigh technique: As he inspects your door, the serviceman grimly calls your attention to "cracks" in your garage door. These appear very faintly in the middle of the door where the panels bow under their own weight when the door is up. This is normal, but the type of thing you wouldn't casually observe yourself. This surprising revelation disarms you, and you may find yourself strangely susceptible to the pitch for an entire new door.
If you've researched this subject at all, you will no doubt have heard that you shouldn't be attempting torsion spring replacement as a do-it-yourselfer. That is generally good advice, so if you have any doubts about your abilities to do risky physical work on your own, hire the job out like everyone else. I found I was capable of doing this work with acceptable risk, because I intelligently understood the techniques, paid careful attention to methods and safety, knew how to use common tools in good condition, properly improvised the special tools I didn't have, and diligently attended to correctly performing a few moments of hazardous manipulation. I learned to do it purely on my own based mostly on bits of advice reluctantly given in Internet forums such as the Usenet newsgroup alt.home.repair. When I first wrote this page in 2002, there was no other do-it-yourself information available on the Web, and it was not until 2005 that reliable information disclosing the techniques started to appear elsewhere (see links below).
Not only was the upward-lifting garage door and the electric garage door opener invented by Overhead Door Corporation’s founder C.G Johnson in the 1920s, but we also have a tradition in excellence for garage door repair, service and maintenance. Even with the most reliable products problems can arise and when they do it’s important to know who to contact to fix these issues while providing solutions to prevent future complications.
The third stage of garage door opener technology uses a frequency spectrum range between 300-400 MHz and rolling code (code hopping) technology to defeat code grabbers. In addition to transmitting a unique identifier for the remote control, a sequence number and an encrypted message are also sent. Although an intruder could still capture the code used to open a garage door, the sequence number immediately expires, so retransmitting the code later would not open the garage door. The encryption makes it extremely difficult for an intruder to forge a message with the next sequence number that would open the door. Some rolling code systems are more involved than others. Because there is a high probability that someone will push the remote's button while not in range and thus advance the sequence number, the receiver does not insist the sequence number increase by exactly one; it will accept a sequence number that falls within a narrow window or two successive sequence numbers in a much wider window. Rolling code technology is also used on car remote controls and with some internet protocols for secure sites.
“This is not a simple thing to install,” cautioned one of our testers. “It's likely that you’ll make a few trips to the hardware store even if you’re very handy and have a relatively complete set of tools.” That said, our reviewers thought that this opener’s instructions themselves were very clear and that once setup was complete, the device “worked without lots of fiddling.” Another plus was its added security features, like keyless entry and smartphone app integration. Lastly, our testers did wish it had a built-in camera to allow surveillance in the garage at all times.
You might genuinely need some extra parts when you thought you simply needed a broken spring replaced, and a good serviceman will perform a simple inspection to identify such parts. Nor is it unreasonable for a business to charge separately for a service call versus repair work actually performed. But the best protection for you as a buyer, being somewhat at the mercy of whomever you decide to bring on site, is to understand what is being done, and ask intelligently for a clear explanation or demonstration of why extra parts are required.

Garage Door Opener

×