All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.

Roller doors ("Sheet Doors"-USA) are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g.; transparent corrugated fibreglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Larger roller doors in commercial premises are not sprung (except USA) and use a manual pulley and chain system or a geared motor to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.

In each of our branches, we have the best team of expert professionals who know how to handle each and every type of garage door and its components. This is because all of our technicians go through a rigorous training process, covering every known garage door repair technique. We do not let them onto the field until we know that they are completely trained, and can perform a job to perfection. Aside from this, they are continually updated with all the latest knowledge, information and training in order to do their work efficiently.
Correct spring size is determined by factors such as the weight and height of the door. You cannot substitute a different spring and just tighten or loosen the winding to make it balance the load. Why? To maintain cable tension under all operating conditions, the spring must retain about one turn of unspent wind-up at the top-of-travel position, which with the lift drum size and door height predetermines the number of turns of winding at the bottom-of-travel; and furthermore the torsion of the fully-wound spring at the bottom-of-travel must be slightly less than that needed to lift the weight of the door when translated by the lift drums.
Technician Mark called 1/2 hr before coming. Very knowledgeable and friendly technician. Originally scheduled as a tune-up but after pointing out several potential problems I decided on the complete overhaul package. All parts were on the truck. Technician completed job in a little over an hour. Very satisfied. Definitely would recommend.Bob PNorth Myrtle Beachread more
Disclosure: This post is brought to you by the Insider Picks team. We highlight products and services you might find interesting. If you buy them, we get a small share of the revenue from the sale from our commerce partners. We frequently receive products free of charge from manufacturers to test. This does not drive our decision as to whether or not a product is featured or recommended. We operate independently from our advertising sales team. We welcome your feedback. Email us at [email protected]
With over 300 independently moving parts, your garage door is a deceptively complex piece of equipment. To help prevent malfunctions and break-downs, it is a good idea to occasionally perform a garage door tune-up to keep all of these parts in good working order. A regular tune-up service by a Sears professional can prevent unexpected door problems and prolong the life of your existing equipment.
Technician gave me a window of 1-4pm, I called at 330 to see if he was on his way. He told me he would be there at 4pm, reason being was because of the amount of work orders he had that day. He was also by himself, had no helper. I was very satisfied that he was able to repair my garage door. He was very professional considering he showed up on a Friday afternoon on a 100 degree day. Thanks again
The technician that came out, Todd Noel, was very friendly and professional. He fixed my problem quickly and did not overcharge me for something that I did not need. He also made some great recommendations for future work. Because of his level of service and my customer experience, I highly recommend Precision and will use them again in the future.
For Sears Garage Door Installation and Repair Services, making your garage door safe is as important as making it function well. For this reason, all of our repair services and tune-ups feature a 20-point safety check. Our technician will carefully examine your garage door panels, springs, sensors, safety release, hardware, track, and more. This ensures that, not only has our work been done well, but that your garage door poses no danger to your vehicles or family. Due to the intricacy of garage door systems, only garage service professionals should attempt to adjust, repair, or service door equipment.
GREAT Company. Called in at 1:30 on a Saturday and my issue was fixed by 3:30 that same day. Our service tech Ken was a great guy who was A++++Can't ask for a better experience than I had with this company. I highly recommend this company and Ken to everyone. And their rates are very fair. GREAT Company to deal with. I wish any other contractor I've dealt with were even half as good as this company. A+++++++ all the way.read more
When you're done watching this video you'll know how to determine whether the company you hired to replace your garage door spring installed the right size spring on your door. You'll also learn the consequences to your garage door opener if the wrong size spring is used. If you are having a problem with your garage door spring, the 2:30 minutes you spend watching this video is time will spent.
Overhead Door™ products automatically include the unequaled expertise of Overhead Door™ Distributors. Combined with our innovative product design and manufacturing superiority, our distributors are a proud part of the family, sharing our name, Red Ribbon logo, and commitment to excellence. Our network of more than 400 Overhead Door™ D​istributors ensures you have convenient access to our commercial doors and operators, residential garage doors and openers, and accessories wherever you are. This extensive distribution network is unique in our industry, providing a single source for personalized design and application consulting, quick installation, turnkey services and professional maintenance.
Though you can do some maintenance to your garage doors on your own, it may be a good idea to schedule routine inspections with a professional. A typical service call will include a manual inspection of the door and opener. Then adjustments can be made including spring tension, chain/belt tension, limits and force adjustments and door lubrication. Fees for this service vary from place to place, but garage door repairs typically cost between $147 and $340.
Garage door repair is a specialized job, which is typically handled by a garage door repair service. Professional garage door repair technicians can test or repair a garage door system and fix cosmetic blemishes on doors. Common requests include help with jammed or inoperable doors, slow or erratic doors, unusual sounds, dents or scrapes on the door, and general system testing. Garage door repair professionals can work on single-car, double-car and RV-size garage doors.
Garage doors cause injury and property damage (including expensive damage to the door itself) in several different ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on extension spring systems).
Measure springs only when relaxed: Measurements must be taken on a relaxed spring because the winding adds significant overall length while reducing the coiled diameter. If you have a paired design, and one is broken and one is intact, then don't try to measure the length of the intact spring with the door down. A wound spring has 7 or 8 turns adding to the overall length, and will therefore be about 2 inches longer than when relaxed. Measure the lengths of the pieces of the broken spring, which will be unwound, and add them together. As a check, one can measure the length of the intact spring after it is unwound in the procedure to follow below. Be sure also to observe whether the springs are originally of equal sizes, because it is quite possible that they are not.

You must use springs that are matched to the weight of the door. You cannot compensate for the wrong size spring by adjusting the number of winding turns. If you do not know a proper spring size, then you or your spring supplier must calculate a proper size (see below) based on an accurate weight (within 5 pounds) of the door. So you must then in turn have an accurate weight.
Fortunately, owners aren't bashful about weighing in on their garage door openers. Though some models get only a handful of reviews others receive hundreds of unique ratings on sites such as Amazon, Home Depot and Lowe's. If you are interested in a Craftsman garage door opener, Sears is the place to visit. While our research reveals that no garage door opener is perfect, several models jump to the fore as offering good performance and good value in the eyes of owners. These are the openers that we've named Best Reviewed for this edition of our report.
Absolute Overhead Door recently launched a blog that can be found here so that readers would be able to see the benefits of a garage and what they should do in the event their newly driving teenage drove into the garage door. The blog offers many tips for “fix at home” solutions as well as giving examples of situations when calling us for a service call is the best decision. In our blog, we give professional and honest recommendations for the most reader and budget friendly options for families looking for advice that doesnt cost a fortune and an obligation to purchase a new garage door from a salesman afterwards! Check it out! We hope you enjoy it.
Please Note: Prices, promotions, styles and availability may vary by store and online. Inventory is sold and received continuously throughout the day; therefore, the quantity shown may not be available when you get to the store. This inventory may include a store display unit. Online orders and products purchased in-store qualify for rebate redemption. Rebates are provided in the form of a Menards® Merchandise Credit Check valid towards purchases at any Menards® retail store. Not valid for purchases on MENARDS.COM®.
The most common problem with garage door openers is the door reversing when it’s closing, even when there’s nothing obvious obscuring the photoelectric eyes. If your closing force is adjusted correctly, then the problem is almost always the photoelectric eyes. The eyes are very sensitive— even cobwebs can interfere with them. First make sure the eyes are still in alignment (some- thing may have knocked them out of whack). Then make sure the eyes are clean and the path between them is clear. Finally, look for loose wires in the eyes and the opener.
Since 2015, we’ve tested a variety of devices such as smart locks, video doorbells, DIY home security systems, thermostats and more. We use these testing experiences to inform our evaluations of other equipment. As time and resources allow, we occasionally test new types of products, but there are still some circumstances where we’re unable to conduct in-house tests. When testing isn’t possible, we conduct thorough research using the same standards we apply to our in-house tests – this is the case with smart garage door openers. We’ve reviewed garage door openers since 2011. 
Wood doors range from midprice to very expensive, depending on whether they consist of a lightweight wooden frame filled with foam insulation and wrapped in a plywood or hardboard skin (the least expensive) or are true frame-and-panel doors made of durable mahogany, redwood, or cedar. Wood doors usually carry a short warranty, perhaps only one year. 

Step 1: Check the metal tracks inside the garage. Look at the mounting brackets that hold the tracks to the walls. If they're loose, tighten the bolts or screws at the brackets. Working inside the garage with the garage door closed, examine the tracks for dents, crimps, or flat spots. If there are any damaged spots, pound them out with a rubber mallet, or with a hammer and a block of scrap wood. If the tracks are badly damaged, they should be replaced.
Drive type Garage door openers work in a variety of ways. A chain-drive model raises and lowers doors with a metal chain — these tend to be inexpensive and able to handle heavier doors, but they’re loud. A belt-drive opener uses a belt and operates more smoothly and quietly. Screw-drive openers, which lift doors with a threaded steel rod, are also quiet and don’t require much maintenance. Finally, a direct-drive opener operates as a single unit — the whole contraption moves to lift the door. These tend to be the quietest, smoothest mechanisms available.
We are a family owned and operated company with local offices in various cities. We have offices in Arizona — from Phoenix to Tucson; Nevada— covering the entire Las Vegas metropolitan area, from North Las Vegas to Henderson; the Sunflower State of Kansas, from Wichita to Junction City; Wisconsin — spanning the entire Milwaukee county, from Fox Point to South Milwaukee; and Michigan, with our base in Sterling Heights.

The replacement springs in my case proved to be 0.2253 wire size, 2.0 inch (inside) diameter, and 24 inches long, in a pair of one left- and one right-hand winding. Actually, the old springs in these pictures were a slightly smaller size, but another similar door on this garage was better balanced by that size. Whoever installed the old springs didn't quite get the weight and size just right; it is not unusual to find a repair service installing a slightly off-balance spring size that happened to already be on the truck during the service call. My electric opener had no trouble handling the small imbalance. But since it is safer to reduce the electric operating force as much as possible through careful balancing, I chose the size that was working better on the other door. The Chamberlain brand electric openers (also sold by Sears) I have incorporate a plastic worm gear that tends to wear out after some years of use, requiring a disassembly and installation of a $20 repair kit; this wear is minimized by a properly balanced door.
The prior clamping of the set-screws tends to have pressed a dimple into the hollow shaft and to have distorted the shaft's roundness into an eccentric shape. While releasing the set-screws, I was careful to loosen them enough to let the cone swing around any such distortions. I was also careful to observe any binding of the old cones on the eccentricity or burring on the shaft. The fit of the cone on the shaft is supposed to be loose enough to avoid binding, but if it were to occur one would have to be careful not to assume the spring was unwound when in fact the cone was just stuck on the shaft. If I had a stuck cone that I could not unwind with a little extra force, then I would have called in a technician to deal with it. In the worst case, I suppose the spring must be deliberately broken with some hazard, thus releasing it for a forceful disassembly, and the shaft and some other parts replaced. But this is an unlikely situation and in this case was not necessary.
We lead busy and sometimes hectic lives. It's easy for someone low on sleep and high on stress to accidently bump into their garage door leaving a little damage. If you're lucky it's just an individual garage door panel that's been damaged. This will leave you with the option of garage door panel replacment. There's a chance it might cost you upwards of $150-200 to spot repair damaged garage door panel. If it happens to be an in-production model, they probably will be able to repair or replace the entire panel (if needed) for $250-400. Unfortunately if you've got an older model of garage door the panels may no longer be in production. This might seem like a disadvantage because you'll end up having to just replace the entire door. Many times it's actually easier and more cost effective to just replace the garage door.
However, if you are confident that you don’t just need new batteries, make sure to call a professional. A service person with a lot of experience will be able to look at the problem and quickly diagnose the issue, saving you precious time. Again, while you may be able to save money in the short term by taking a day off and troubleshooting the problem yourself, the amount of energy and time lost as you search out the issue will quickly surpass the cost of a professional repair.
Modern garage door openers include basic to advanced features that improve safety and deter break-ins. Examples include an automatic stop if a descending door encounters a solid object such as the hood of a car and light beam sensors that detect the presence of an object -- or a person or pet -- and stop a garage door's downward movement before accident or injury can occur. Available security options include remote lockouts for when you will be away from home for an extended amount of time, remote codes that change after each use, and lights that turn on automatically when your garage door opens or if movement is detected inside.
A typical version of an overhead garage door used in the past would have been built as a one-piece panel.[1] The panel was mounted on each side with unequal parallelogram style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers.[1] The weight of the door may be 400 lb (181.4 kg) or more, but is balanced by either a torsion spring system or a pair of extension springs.[2] A remote controlled motorized mechanism for opening garage doors adds convenience, safety, and security.[3]
Direct Drive - Unlike chain- and belt-driven systems, where the motor remains stationary while moving a chain, a direct drive motor moves while the chain stays in place. Because of this, the only moving part is the gear the motor uses to move while lifting the door. To our knowledge, only one company makes direct drive garage door openers: Sommer. The company claims the motors are more efficient and quieter than any other type of opener. However, this is the most expensive type of opener we’ve found, costing around $286 on average.
Lift cable placement: On the standard residential door mechanism, the loops at the lower ends of the two lift cables loop over the two bottom roller shafts which project from the bottom bracket on the door. The upper cable ends fasten to the drums using one of the methods described above. The drums are positioned along the torsion shaft such that the inner edge of each drum is approximately over the edge of the door. The cable winds onto the drum from outside in, so at the top of travel the cable is winding onto the inner edge of the drum, vertical from the edge of the door where it is looped over the roller shaft. As the door is lowered, the cable winds out to the outer edge of the drum, and thus is a bit out from the vertical, but the cable still falls in the gap between the guide rails and door edge. My cables rub and slap on the rails a bit, but after 30 years and many 10,000s of cycles, they don't seem to have worn at all.

Luckily, there is a bit of science to questions of garage door repair and replacement. That’s why we’ve put together this guide on when to replace a garage door. We’ll prepare you to compare repair vs replacement garage door costs. We’ll discuss the ways in which repairs are the most affordable option while also exploring those moments when replacement will in the end provide you with more value added.
While a sudden issue is usually easily repaired, a consistent issue that has gone unaddressed for months or years will likely require a total replacement. The problem is that garage doors have a number of heavy, powerful moving parts. If the door is working as it is designed, it can open and close hundreds and hundreds of times without issues. However, if there is even a small issue in the lifting mechanism that repeatedly influences the movement of the door, you will soon find that the damage caused over those hundreds of lifts can’t be fixed.
Most garage door openers are pretty expensive. So if you need an opener on a budget, the Genie 1035-V (also known as the Genie Chain Drive 500) gives you that desirable low price point. It doesn't have a lot of high-end tech features, nor will it manage heavy garage doors, but it does the basic work of raising and lowering the garage door perfectly well.
Torsion springs are devices that lift most of the weight of a garage door so that the door can be opened manually or by an electric opener. The torsion principle is applied via an efficient and economical apparatus consisting of a torsion shaft under spring torsion, which turns lift drums, which wind cables attached to the door near the bottom. All of this apparatus is mounted over the top of the door. The energy stored is sufficient, in an uncontrolled release, to break things, hurt you, or perhaps even kill you. The same could be said of jacking up your car to change a tire, or mowing your lawn, or raising children, so it is not crazy to want to do this yourself.
We’ve earned that reputation by always putting our customers first. When it comes to residential and commercial garage door repair services in northern Kentucky and Cincinnati, you’ll always get our best. That includes reliable installation, quick and responsible customer service, free and fair estimates on our work and 24/7 emergency service when you need it the most. We have designed our installation and repair services to make sure you get the most out of your garage door for as long as possible.
If you're clever and equipped with a welder, you might think you could get away by welding a broken spring back together. At least two factors make this extremely risky. First, the weld itself may fail, either due to insufficient basic strength, or weakening of the nearby parts of the spring. Second, the fact that the spring was old and fatigued enough to break once, means that it is likely to break again soon at other location(s).
Garage doors provide one of the major entryways into your home. Therefore, it is essential to ensure that they are secure and in good working order. If you are having problems with your current door, then you need to have a professional determine if it can be repaired or if it will need to be replaced. Here are some of the most common factors that will affect the cost of a garage door repair.

We guarantee same day garage door service on calls placed by 1:00 pm. We are on most jobs within 2 hours of the request for service being placed. All our technicians travel in fully stocked trucks to your home or business to enable us to complete nearly all overhead / garage door repairs on the first trip without the need for additional appointments just to complete the job. We guarantee to exceed the normal service appointment you have experienced with other garage door companies by implementing the Absolute 22-point inspection on all jobs that we take on. Our 22-point safety inspection ensures the customer that all vital mechanical and safety parts of the door are fully operational and functioning as they should be. This prevents any future service calls for our customer and in turn saves YOU, the customer, money!

The standard winding tools are simply a pair of 18-inch lengths of mild steel rod, 1/2-inch diameter. Winding cones can have different socket sizes (such as 5/8 inch instead of 1/2 inch), so it is important to measure the socket and select a matching rod diameter. Also beware that poor-quality cones may have a sloppy fit to the winding bars, and a loose fit presents a severe hazard of slipping at the worst moment; anything more than about an inch or two of play at the handle end is too loose for safety. I bought a 3-foot length of zinc-plated 1/2-inch diameter steel rod from Home Depot for about $3, which conveniently cuts into two halves of just the right length (the store might even cut it for you if you ask). A steel supplier selling at commodity prices might charge about 50 cents or so for such a piece that weighs about 2 lbs. Drill rod would work if used in the annealed condition in which it is originally sold, but the added expense provides no benefit and the brittleness (if it had been hardened and not annealed) would worry me a bit. Rebar, threaded rod, screwdrivers, etc., are absolutely foolish as they will not fit the socket snugly. Aluminum rod is definitely too weak, and will bend under the torque that must be applied. Longer rods would make for more leverage but unwieldly swing; shorter rods make for uncontrollable swing. As we'll calculate below, the 18-inch standard tool length is an appropriate compromise. Note that you do not need 18 inches of ceiling clearance above the torsion shaft to use an 18-inch rod, since you need not swing the rods above horizontal when winding.

To estimate the maximum physical force required to wind these springs, consider that they are balancing the weight of the door with a torque applied to a lift drum on each end of the torsion shaft. The lift drums have a 2-inch radius, which is the standard residential size, and corresponds conveniently to about a 1-foot circumference. If we pessimistically assume the 10-by-7-foot door has a weight of 350 pounds, this implies a torque of 350 pounds on a 2-inch radius, that is, 700 inch-pounds, or 58 foot-pounds. Each of the two springs should be exerting slightly less than half of the balancing torque, or 29 foot-pounds. Compare this to, say, the bolts in an automobile, which are typically torqued to values of about 50 foot-pounds, or tire lug nuts, which may be torqued to well over 100 foot-pounds.
The best garage door openers can be controlled from a remote location through your phone. If you’ve ever left home and had a moment of panic, not knowing if you left the garage door open, this feature can give you peace of mind. The door opener’s built-in Wi-Fi connects directly with your home Wi-Fi router, which allows you to close your garage door from wherever you are through a MyQ smartphone app. The Chamberlain Group opener has this feature – it’s a 1-horsepower garage door opener with extra lifting power for unusually heavy doors of over 500 pounds.

Welcome to Jarusewski’s Overhead Door Service Inc. We are a locally owned company that has been providing the Carlisle, PA area with garage door sales and service since 1988. We specialize in installation, repair and maintenance of residential and commercial garage doors. Our garage doors are reliable, affordable and most importantly safe.We know a great garage door installation is nothing unless you have a great garage door to install. That’s why we feature the best brands when it comes to garage doors and garage door openers. We feature doors by Clopay, as well as, door openers by Chamberlain and LiftMaster Professional.
Give your garage a great look with garage doors from Menards®. Menards® has all the supplies, tools, and accessories you need to install a stylish new garage door. Choose the perfect door from our selection of residential and commercial garage doors as well as roll-up doors for storage sheds. At Menards®, you will find a wide variety of door sizes ranging from 4 feet to 9 feet wide, 10 feet to 16 feet wide, and over 16 feet wide. Because of the layer of insulation, insulated garage doors are generally quieter than noninsulated doors. Insulated doors also offer improved energy efficiency, so you can stay comfortable while working in the garage no matter what the weather's like outside.
×