Garage remotes work by sending a coded signal via radio frequency to the garage door opener. If this code matches that of the opener, then the motor will operate and raise or lower the door. Older devices use a single coded switch, whereas newer systems utilise a rolling code that changes each time the remote is used, increasing the security of the door by offering billions of combinations.
The chain-driven Chamberlain C410's .5-horsepower motor has enough power to handle most residential garage doors. Owners say it lifts even heavy doors easily. While chain-driven openers generally are louder than belt-driven models, most say that, like its predecessor model, it's actually pretty good in that regard, and we saw fewer complaints about installation challenges, too. The opener is also well-equipped in the feature department, though you'll need to spend a bit extra if you want to use its smart functions.
Thank you for visiting Precision Garage Door Service of Seattle. We specialize in the repair of residential garage doors, openers, sales, service, & installation. Where ever you live along the Wasatch front, You have my personal guarantee that your experience with us will be professionally handled from start to finish. Your service will be provided by qualified & certified technicians that have completed the most extensive & rigorous training in the industry. We are proud of our environmentally sensitive business practices. Please give us a call to discuss your specific needs. We look forward to serving you.
Extremely straightforward and efficient estimating and installation process. We purchased a Clopay sectional steel garage door for our double garage that works flawlessly with our existing door operator. The guys suggested an insulated door, but I thanked them and said no because I don't care for the garage to warm up in the winter and create a corrosive atmosphere of melting snow and salt. Great job!

Critical measurements: Torsion springs come a variety of standardized sizes, so you have to carefully measure the old springs to know what to order for proper replacements. Tables of standard sizes and designs are on the Web, such as here [www.industrialspring.com]. The four critical measurements (all in inches) are: (1) the wire thickness (which I'm measuring here with a dial caliper; you can also measure the length of a number of closely stacked turns with a ruler and divide by the number of turns in the stack, measuring 10 turns this way makes the math easy), (2) the inside diameter (not outside!) of the relaxed (not wound!) coil, (3) the overall length of the relaxed (not wound!) spring coils, not including the winding cones, and (4) the right- or left-hand winding of the spring. One must glibly quote those figures to the spring supplier, otherwise one's lack of expertise will be obvious, and one will not be worthy of buying the parts.
Spring stretch: When the door is at the top of travel, the spring(s) are hardly wound, but are stretched, so on a single-spring installation this stretch tends to pull the shaft towards the non-spring side. With two springs, the stretch tends to cancel out. This top-of-travel spring stretch, being about 7 or 8 turns of the wire, will thus amount to upwards of about 2 inches on a typical size spring of 0.253 wire. This spreads out to a gap of about 0.020" per coil on a typical 100-coil spring, so the stretch is not very visible.
The history of the garage door could date back to 450 BC when chariots were stored in gatehouses, but in the U.S. it arose around the start of the 20th century. As early as 1902, American manufacturers—including Cornell Iron Works—published catalogs featuring a "float over door." Evidence of an upward-lifting garage door can be found in a catalog in 1906.[4]
Before setting the last panel in the tracks, set the power unit on the actual frame and slide it in the ends. Hardened screws are used to attach the center bracket (Image 1). They are a different type screw — they are tougher and will last a lot longer. Make sure the bracket is level (to the eye) when installed and leave the bracket a little loose so adjustments can be made. Fasten down all the hinges (Image 2).
Torsion springs are devices that lift most of the weight of a garage door so that the door can be opened manually or by an electric opener. The torsion principle is applied via an efficient and economical apparatus consisting of a torsion shaft under spring torsion, which turns lift drums, which wind cables attached to the door near the bottom. All of this apparatus is mounted over the top of the door. The energy stored is sufficient, in an uncontrolled release, to break things, hurt you, or perhaps even kill you. The same could be said of jacking up your car to change a tire, or mowing your lawn, or raising children, so it is not crazy to want to do this yourself.
Whatever problem you are having with your garage door or garage door opener, you can count on Aaron’s Garage Door Service to provide you with the best service in town. We are an honest company that has built the reputation of our quality service. We don’t deceive people by offering a free service call or discount coupons to get the job then jack up the prices at the end. You can always count on Aaron’s Garage Door Service when you have any type of garage door problem.
Your ad had no cheap coupons or promises.. Just business. Service was more than prompt. No attempt to fix something that was not broke or did not try to sell me anything I did not need. He stated the price at the beginning and stuck to it. (I was so pleased, I did not bother to mention a senior discount.) Very, very pleased that I have found someone I can trust and rely on. GaryRichard

Garage Door Service

×