To make sure the job gets done right, our professional installers are local, licensed and insured. With a 9.7 out of 10 VOC score, our garage installers will exceed your expectations, provide reliable service, and install attractive garage doors that will transform your home’s appearance. All labor, products and installations are 100% backed by The Home Depot. Service you can trust.
The inside of the door panels bear a few dings, since filled with Bondo, from my teenage boys shooting hockey pucks. The streaks on the right that look like dinosaur claw scratches came from operating the door inadvertently when the rear doors of a van were open. The responsibility for these scars is all mine; they have also been Bondo-filled. We tend to use a lot of Bondo around our house. The crud on the walls and ceiling are cobwebs and dust infiltrates.

I obtained my parts, as described on this page, from American Garage Door Supply Inc. (http://www.americandoorsupply.com/) They may have raised their small-order prices or imposed a minimum order since I ordered from them in 2002 at the prices in my essay above. The Web site offers a free catalog by PDF download or mail. Springs in 2005 were priced at $2.25/lb.
If the wires that run from your opener to the photo eyes and to the wall button are exposed, replace them, too. Those wires have probably been in your garage for 10 years or more, and they may be nicked or worn. Newer openers are extremely sensitive and won’t work if a wire is damaged. It only takes about 15 minutes to run the new wire, so it’s time well spent. If the wires are protected inside the wall, you don’t need to run new wire.
Looking for another budget option? This one, also from Chamberlain, is a good choice. With a powerful ½ horsepower motor, it’s reliable and rugged, especially paired with its industrial strength chain drive. The 100-watt bulb gives you some overhead light that guides you into your home from your car safely. It also comes with a pre-programmed, one-button remote that can be used over a long range. Plus, there are safety sensors that project an invisible beam helping to prevent the door closing on people or objects. And when the door is closed, you can rest assured it’ll stay closed and locked thanks to its Patented Security + 2.0 rolling code technology and PosiLock anti-theft protection.
The electronics should also be inspected before or after investing in the cost of replacing the garage door panel to make sure your door will operate properly. The sensors prevent the door from closing on someone's foot or a pet. If they don't work, someone could be injured. Also check to make sure the door opener works, since you could otherwise be locked out of your garage.
Finding the best rated garage door openers is a bit of a challenge. Quality professional reviews are currently hard to come by, and we did not spot any that addressed current models. About the only credible, current, testing-based feedback we spotted was from Wirecutter, and it addressed smart garage door controllers rather than openers. That said, if you would like to add smart features to an existing garage door opener that you are otherwise perfectly happy with, the review is worth a read.
Wood - Wood garage doors are sturdy and quite beautiful. However, if you live in a humid climate, your doors will be prone to rotting and splitting. If your wood is painted, you must also factor in the costs of painting as part of your regular maintenance routine. The cost of repairing the wood varies depending on the type. However, average cost to repair a wood panel is $190 to $215.

While a sudden issue is usually easily repaired, a consistent issue that has gone unaddressed for months or years will likely require a total replacement. The problem is that garage doors have a number of heavy, powerful moving parts. If the door is working as it is designed, it can open and close hundreds and hundreds of times without issues. However, if there is even a small issue in the lifting mechanism that repeatedly influences the movement of the door, you will soon find that the damage caused over those hundreds of lifts can’t be fixed.


Critical measurements: Torsion springs come a variety of standardized sizes, so you have to carefully measure the old springs to know what to order for proper replacements. Tables of standard sizes and designs are on the Web, such as here [www.industrialspring.com]. The four critical measurements (all in inches) are: (1) the wire thickness (which I'm measuring here with a dial caliper; you can also measure the length of a number of closely stacked turns with a ruler and divide by the number of turns in the stack, measuring 10 turns this way makes the math easy), (2) the inside diameter (not outside!) of the relaxed (not wound!) coil, (3) the overall length of the relaxed (not wound!) spring coils, not including the winding cones, and (4) the right- or left-hand winding of the spring. One must glibly quote those figures to the spring supplier, otherwise one's lack of expertise will be obvious, and one will not be worthy of buying the parts.

Irvine, CA | Foothill Ranch, CA | Lake Forest, CA | El Toro, CA | Laguna Hills, CA | Laguna Woods, CA | Rancho Santa Margarita, CA | Coto De Caza, CA | Mission Viejo, CA | Aliso Viejo, CA | Laguna | Niguel, CA | Laguna Beach, CA | San Juan Capistrano, CA | Dana Point, CA | Capistrano Beach, CA | San Clemente, CA | Corona Del Mar, CA | Ladera Ranch, CA | Cypress, CA | Dove Canyon, CA | Seal Beach, CA | Villa Park, CA | Westminister, CA | Anaheim, CA | Anaheim Hills, CA | Pomona, CA | Garden Grove, CA | Brea, CA | Placentia, CA | Fullerton, CA | La Palma, CA | Buena Park, CA | La Habra, CA | Costa mesa, CA | Cowan Heights, CA | Fountain Valley, CA | Huntington Beach, CA | Newport Beach, CA | Balboa Island, CA | Tustin, CA


If you've researched this subject at all, you will no doubt have heard that you shouldn't be attempting torsion spring replacement as a do-it-yourselfer. That is generally good advice, so if you have any doubts about your abilities to do risky physical work on your own, hire the job out like everyone else. I found I was capable of doing this work with acceptable risk, because I intelligently understood the techniques, paid careful attention to methods and safety, knew how to use common tools in good condition, properly improvised the special tools I didn't have, and diligently attended to correctly performing a few moments of hazardous manipulation. I learned to do it purely on my own based mostly on bits of advice reluctantly given in Internet forums such as the Usenet newsgroup alt.home.repair. When I first wrote this page in 2002, there was no other do-it-yourself information available on the Web, and it was not until 2005 that reliable information disclosing the techniques started to appear elsewhere (see links below).
A rolling code is a protocol used by garage door openers to keep your door safe and secure. When the radio signals from your remote control are broadcast to your garage door opener, it uses a specific code to communicate. Older models used the same code every time, making garage door openers vulnerable to burglars using a radio frequency identifier device. 
Align the upper roller tracks by carefully lifting the door halfway. Lock it in place with two locking pliers, and install the supporting brackets on the back of the rails using 1-1/4 in. perforated angle iron (available at home centers and hardware stores). Install 1-1/2 x 1/4 in. stop bolts, with the threads to the inside of the track, at the end of each upper track.

Absolute Overhead Door Service was founded by Vince Heuser when he saw the need for a new garage door company that performed at a much higher standard than most companies in the local area. He understood and saw that the need for HONEST, knowledgeable, dependable, and friendly technicians was apparent and Absolute Overhead Door Service was then founded in 2007. With our extraordinary growth because of our outstanding service, we cover the entire Central Kentucky area including Louisville, Elizabethtown, Bardstown, and Southern Indiana. We have warehouses strategically located so our technicians can be on your job within two hours on most days with no extra charges anywhere or anytime in normal hours. No other local company provides the convenient service hours that we do, 8am-6pm Monday-Saturday and Emergency Service after 6pm, Monday thru Friday, and on Sunday’s. We guarantee same day service on calls by 1pm and still get most service calls up to 4pm the same day.
Our value pick is the Chamberlain PD76EV. It costs about $50 less than our top pick, but it has most of the higher-priced model’s advantages. The PD76EV has the same lift capacity, horsepower, lift system and automation compatibility. However, it doesn’t come with advanced features such as a backup power source, close timer and keyless entry pad. If you can live without those, this opener is a great choice.
They sent Doug Fussell out to my house on the day after Christmas! I had only called them three days before! Doug was a premier technician, very thorough and very efficient. I expected him to take two days, since he was replacing two doors and adding openers on each door. He only took the daylight hours of one day! I could not believe how fast he was! In addition, he thoroughly taught me how to use the remote openers. I highly recommend them to anyone!
If you have a steel door, but want the look of a wood one, it is not necessary to change your entire garage door. Often, it may be possible to mimic the look of wood with skillful painting. Your local home improvement store may be able to provide good advice about the type of paint and brushes needed to mimic the look of wood for your particular door material.
We guarantee same day garage door service on calls placed by 1:00 pm. We are on most jobs within 2 hours of the request for service being placed. All our technicians travel in fully stocked trucks to your home or business to enable us to complete nearly all overhead / garage door repairs on the first trip without the need for additional appointments just to complete the job. We guarantee to exceed the normal service appointment you have experienced with other garage door companies by implementing the Absolute 22-point inspection on all jobs that we take on. Our 22-point safety inspection ensures the customer that all vital mechanical and safety parts of the door are fully operational and functioning as they should be. This prevents any future service calls for our customer and in turn saves YOU, the customer, money!
Good response time and service; Question - I googled to find the Sears Garage Door repair phone number. During the conversation, I was unsure if this was "Sears" or a "contractor service" or other service. I had to ask if this repair person was coming from "Sears" or an independent repair. I was concerned until the service man arrived in a sears truck wearing Sears apparel. You might want the process to be more clearly identified as Sears.
When buying an opener, choose a 1/3 hp or 1/2 hp opener for a single garage door (1/3 hp can be hard to find at some home centers). Go with 1/2 hp for a double door and 3/4 hp for a door that has a wood or faux wood overlay (they can be heavy!). Openers have a set opening speed, so installing an opener with a higher horsepower won’t open your door any faster.
Some garage door openers are compatible with HomeLink, a remote control technology that's built into some automobiles. However, due to a technology change, many older HomeLink-equipped cars are not compatible with new HomeLink-enabled garage door openers without the purchase of an optional interface; you can also simply ignore your car's built in controls in favor of the remote control that comes with the opener, but that's a solution that seems to annoy owners.

Whether you're planning on moving in the future or you're fixing up your forever home, replacing a garage door can provide an excellent return on investment and boost your home's resale value. According to Remodeling magazine's 2016 Cost vs. Value report, garage door upgrades provide a nationwide average return on investment of over 90%, making it one of the top five home improvement projects.
Dodging a falling door:: Reversing this equation gives us x=gt^2/2 as the fallen distance x for a given time t. How much time would you have to dodge a falling door if the spring were to suddenly break at the top of travel? Let us assume you are 5.5 feet tall, so the door will hit your head after falling 2 feet from its 7.5 foot fully-raised height. This 2-foot fall takes sqrt(2*2/32.2) = 0.35 seconds (350 milliseconds). The quickest human response time is about 200 milliseconds, so even if you are alert to the hazard, this leaves you only about 150 milliseconds to accelerate and move your noggin out of the way. If you are an Olympic gold medalist in the 100 meter dash, you can accelerate (horizontally) about 10 feet/second^2, and your 150 milliseconds of wide-eyed panic will move you all of 10*0.15^2/2 = 0.11 foot = 1.35 inch.
My garage door broke on a Saturday night as I was getting ready to leave for a holiday party. Kelvin was here within 30 minutes. He reviewed everything with me that was happening with my door. He gave me the estimates of what was immediately needed to be done in order for my door to raise and then what I will need to have done very soon. I could see all the problems he pointed out to me and I decided to have everything done. He completed everything that night. I was very satisfied with Kelvin’s professionalism and the work he did. Thank you again.
However, in addition to potentially causing injuries to the under-prepared DIYer, a malfunctioning door can become a safety hazard to you and your family. Keep in mind, according to the National Electronic Injury Surveillance System (NEISS), over 13000 people checked into hospitals with garage related injuries in the United States in 2007. You don’t want to turn a loved one into a statistic just to save a few dollars!
Though you can do some maintenance to your garage doors on your own, it may be a good idea to schedule routine inspections with a professional. A typical service call will include a manual inspection of the door and opener. Then adjustments can be made including spring tension, chain/belt tension, limits and force adjustments and door lubrication. Fees for this service vary from place to place, but garage door repairs typically cost between $147 and $340.

Step 1: Check the metal tracks inside the garage. Look at the mounting brackets that hold the tracks to the walls. If they're loose, tighten the bolts or screws at the brackets. Working inside the garage with the garage door closed, examine the tracks for dents, crimps, or flat spots. If there are any damaged spots, pound them out with a rubber mallet, or with a hammer and a block of scrap wood. If the tracks are badly damaged, they should be replaced.
At this point I weighed the unlifted door to confirm and fine-tune my calculations. This is not strictly necessary, but it makes the adjustments easier to perform, if you happen to have a scale with the requisite capacity. With some helpers, we first lifted the door a few inches and rested it on blocks of wood to provide clearance underneath. Then I slid a 400-pound-capacity freight scale under the center of the door, we lifted again to remove the blocks, and lowered the door gently onto the scale. This door weighed in at 238 pounds, which is very heavy for a single-car door. Since the outside of the door carries the 3/4-inch plywood paneling to match the house, and that plywood weighs about 2 lbs/sq-ft, I estimate the door weight to be about 7 x 10 x 2 = 140 lbs of paneling with the rest 238 - 140 = 98 lbs the interior panels, hardware, and cobwebs. Knowing this total weight will help later in adjusting the torsion on the springs. After weighing, we removed the scale and blocks, leaving the door fully lowered again. Had I not had a high-capacity freight scale, I might have improvised a crude weighing device from levers and smaller weights of known mass, or a lever arm pressing a reduced proportion of the full weight onto a lower-capacity scale. Another factor to remember is that The weight of a wood door can vary with humidity.
When buying an opener, choose a 1/3 hp or 1/2 hp opener for a single garage door (1/3 hp can be hard to find at some home centers). Go with 1/2 hp for a double door and 3/4 hp for a door that has a wood or faux wood overlay (they can be heavy!). Openers have a set opening speed, so installing an opener with a higher horsepower won’t open your door any faster.
A standard residential door raises 7.5 feet, but since the door goes horizontal this is equivalent to raising the whole door for half that distance, or about 3.75 feet. So if the door weighs, say, 150 lbs, then the energy supplied by the springs is 3.75 * 150, or about 563 foot-pounds. This is like throwing a 50-lb sack of cement up a 11-foot flight of stairs. Or catching a 50-lb sack of cement dropped from 11 feet up.

While you may be able to increase efficiency by replacing the weather stripping at the bottom of an old garage door, the kind of insulation and energy efficient materials used in today’s new doors will make a drastic improvement on your garage’s energy efficiency. Just like the way a new garage door recoups its costs in increased home value, a new door will also quickly pay for itself in energy savings!
The Certified Technician, Rey Lopez, was competent, professional, polite, and willing to work. He quickly removed the old door and installed the new one. He then explained the vast differences between what we originally had and what we'd just purchased (stronger spring/tension rates; increased viability of door opening/closing life; beefier hardware; plastic vs. nylon rollers; stronger door reinforcement). Ray performed with alacrity his tasks and then demonstrated the quiet, solid way the door retracted--no banging after the initial rise from the ground. Finally, his attention to detail was so precise that he enabled another remote controlling all three doors, plus he capped some frayed wires, thus solving the problem of why the door opened intermittently. I would rate him a "6" on a scale of "1-5", meaning he went above and beyond our expectations. His "can do" attitude, coupled with the deference he showed, will take him a long, long way. May HaShem richly bless him in his endeavors!read more
Many garage door opener remote controls use fixed-code encoding which use DIP switches or soldering to do the address pins coding process, and they usually use pt2262/pt2272 or compatible ICs. For these fixed-code garage door opener remotes, one can easily clone the existing remote using a self-learning remote control duplicator (copy remote) which can make a copy of the remote using face-to-face copying.

Drive type Garage door openers work in a variety of ways. A chain-drive model raises and lowers doors with a metal chain — these tend to be inexpensive and able to handle heavier doors, but they’re loud. A belt-drive opener uses a belt and operates more smoothly and quietly. Screw-drive openers, which lift doors with a threaded steel rod, are also quiet and don’t require much maintenance. Finally, a direct-drive opener operates as a single unit — the whole contraption moves to lift the door. These tend to be the quietest, smoothest mechanisms available.


See the Sectional Overhead Garage Door catalog (PDF file) from the Prime-Line replacement hardware company. Their brochure Sectional Garage Door Torsion Spring Installation Instructions (PDF file, part number GD-12280) is brief but informative. Apparently you can only obtain their torsion springs as special order items through mom-and-pop type hardware stores like Ace and True Value, and not the big-box Home Depot and Lowes.
These springs weighed in at just over 9 pounds each, including the winding cones. They are covered with a light film of oil, and at this point the job starts to get messy. The manufacturer has painted them with a "225B24" part number, which no doubt indicates the 0.2253 inch wire size, 24 inches long. Perhaps the "B" indicates the 2-inch inside diameter. Both the left- and right-hand springs have this same number on them.

The Chain Drive Rail Extension Kit for 10'-High The Chain Drive Rail Extension Kit for 10'-High Garage Doors is required for reliable everyday operation of Chamberlain chain drive models in 10-ft. garage door applications. Featuring a quick-install extension rail and replacement chain the kit includes everything needed for quick and easy installation. Includes one-year warranty rail extension replacement ...  More + Product Details Close


The most common problem with garage door openers is the door reversing when it’s closing, even when there’s nothing obvious obscuring the photoelectric eyes. If your closing force is adjusted correctly, then the problem is almost always the photoelectric eyes. The eyes are very sensitive— even cobwebs can interfere with them. First make sure the eyes are still in alignment (some- thing may have knocked them out of whack). Then make sure the eyes are clean and the path between them is clear. Finally, look for loose wires in the eyes and the opener.
Some of the best garage door openers offer special features like a backup power source or a timer that automatically closes the door behind you at a predetermined time. While the door openers we reviewed vary in terms of power, noise and efficiency, they are all effective in the all-important task of letting you come and go with the simple push of a button. Here are the criteria we used to rank the top garage door openers:
You might be thinking: Aha! Why don't we lift the door, clamp it in place, and install the springs while they are thus safely unwound, rather than deal with all that accumulation of hazardous torque? The answer: At the top-of-travel, the unwound springs are not fully relaxed; they are still clamped to the torsion shaft with a significant stretch along the shaft axis, plus about a half-turn to keep the door snug at the top. This extra length amounts to the stacking of extra turns that accumulate from winding, also termed "spring growth" in the business. In my case this is about 7 turns of 0.2253 wire, or about 2 inches. Stretching the spring that much and clamping it with a half-turn or so of twist is not feasible.
Belt driven garage door openers offer a prime level of noise reduction if you want a silent environment in the garage. While common chainlinks will rattle during use, the smooth performance of a belt dampens noise as the garage door slides up and down. Using a 3/4 motor, the Genie SilentMax 750 will easily tackle any typical garage door while keeping the environment quiet and comfortable while in use.
Wheel Track Obstruction – Try closing the garage door manually to see if there are obstructions on the wheel tracks. If that is not the case, examine your tracks for potential damage like dents and bends. Look at your door to see if it is hanging unevenly. If the track is damaged or the door is hanging unevenly, it is time to call a professional for repairs. Track repairs can typically cost $133 to $154. Cost for correcting the uneven hanging of doors themselves can vary greatly, but typically cost about $125.
The garage door is the gateway to your home. By choosing an Overhead Door™ residential garage door, you are doing more than making a home improvement investment. You are making us a part of your daily life and relying on us for safety, security and dependable operation. Indulge your sense of design with a garage door that sets your home apart with style, appearance, safety and comfort. With dozens of garage door models to choose from, the Overhead Door™ brand provides style and design options to fit every home. ​
×