Spring rate and torque: In my spring replacement above, the wire size was d = 0.2253 inches, and the ID was 2 inches, giving a mean diameter D = 2.2253 inches. The number of coils is L/d = 24 inches / 0.2253 = 107, less about 5 dead coils on the winding cones, or 102 active coils. Thus the spring rate is K = (π*28.5*10^6 * (0.2253)^4) / (32 * 102 * 2.2253) = 31.8 in-lb/turn (IPPT). Winding 7.5 turns * 31.8 in-lb/turn yields a torque of 238 in-lbs per spring.

Even if one could somehow stretch and clamp the springs to the proper extra length, the process would still be more trouble, and there would be little or no reduction of risk. Lifting the full weight of the unsprung door by hand and clamping it in the raised position is dangerous in itself, and creates the same amount of stored energy as winding the springs, ready to slip out of your hands. Many doors won't travel far enough up the track to provide clearance to access the springs. You're also going to have to deal with winding stiff steel cables onto both lift drums at once without any resistance to maintain tension. Finally, even if you managed to complete the installation with the door raised, you then have to lower the massive door against an untested balancing torque. If you've made a mistake, then that massive door has nothing but your skeletal force applied through your meat clamps (hands) to prevent it from falling down and crushing whatever is in the way (perhaps your feet?).
Home Depot local Service Providers are background checked, insured, licensed and/or registered. License or registration numbers held by or on behalf of Home Depot U.S.A., Inc. are available at homedepot.com/licensenumbers or at the Special Services Desk in The Home Depot store. State specific licensing information includes: AL 51289, 1924; AK 25084; AZ ROC252435, ROC092581; AR 228160518; CA 602331; CT HIC.533772; DC 420214000109, 410517000372; FL CRC046858, CGC1514813; GA RBCO005730, GCCO005540; HI CT-22120; ID RCE-19683; IA C091302; LA 43960, 557308, 883162; MD 85434, 42144; MA 112785, CS-107774; MI 2101089942, 2102119069; MN BC147263; MS 22222-MC; MT 37730; NE 26085; NV 38686; NJ 13VH09277500; NM 86302; NC 31521; ND 29073; OR 95843; The Home Depot U.S.A., Inc. is a Registered General Contractor in Rhode Island and its Registration Number is 9480; SC GLG110120; TN 47781; UT 286936-5501; VA 2705-068841; WA HOMED088RH; WV WV036104; WI 1046796.
One might stack lumber or arrange some other low platform for a steady footing, instead of the ladder. The aluminum ladder shown here is the splendid 16-foot Krause Multimatic, which carries a Type 1A Industrial rating (300 pound working load); I highly recommend it. However, product liability apparently forced this company into bankruptcy in September 2000 and the company ceased operations in June 2001; see http://www.krauseladders.com (this Web site went dead sometime in mid-2002). The world is a dangerous place.
While winding or unwinding, one must be mindful of the possibility that the spring could break during winding process itself. If that should happen while the spring is significantly torqued, hazardous forces on the winding bar will suddenly become unbalanced, and the bar will take an unexpected jump, possibly injuring your hand or anything else in its path. At the same time, the spring remnants, although captured on the torsion bar, will create a frightening racket that would give the bravest soul a start. So your winding technique should be firmly in control of the rods, and you should not be so delicately perched on a ladder such that a startle will result in a fall.

I think garage doors always show their age, there's no "timeless" garage door in my opinion. Walk passed a bunch of houses on your block, bet you could guess the time frame each one was installed based on the style of the door. Good thing is that garage door styles will only look dated after 15-20 yrs and even after that, they still look fine as long as they are well kept. I say go with what you love!
Tools in Action says the Ryobi Ultra Quiet has plenty of versatility, as you can plug devices into the opener hardware, like a Bluetooth speaker, a fan, or even an 18V Ryobi cordless tool battery. When the opener has power, it will charge the battery. But if your home ever loses power, the 18V battery works as a backup to the garage door opener, allowing it to operate normally.
You'll never ask yourself that question again. Just look at your phone to know for sure. Most smart garage door openers will tell you if it's open or shut. They'll send a message every time your garage door is opened or closed too, if you like. Electric garage door openers provide a huge amount of convenience and safety. Imagine you're in a hurry, it's raining out, you pull out of the garage then press the button on your garage door opener remote. The garage door closes, and you didn't have to get out of your car.
Technician gave me a window of 1-4pm, I called at 330 to see if he was on his way. He told me he would be there at 4pm, reason being was because of the amount of work orders he had that day. He was also by himself, had no helper. I was very satisfied that he was able to repair my garage door. He was very professional considering he showed up on a Friday afternoon on a 100 degree day. Thanks again

You might genuinely need some extra parts when you thought you simply needed a broken spring replaced, and a good serviceman will perform a simple inspection to identify such parts. Nor is it unreasonable for a business to charge separately for a service call versus repair work actually performed. But the best protection for you as a buyer, being somewhat at the mercy of whomever you decide to bring on site, is to understand what is being done, and ask intelligently for a clear explanation or demonstration of why extra parts are required.

Garage Door Opener

×