Like most other product review sites, ConsumerSearch is supported by a combination of commissions on the sale of the products we recommend and ads that are placed on our site by Google. If you find something you like, you can help support us by clicking through and buying the products we pick. Our editorial process is independent and unbiased; we don’t accept product samples, requests for reviews or product mentions, or direct advertising.
A standard residential door raises 7.5 feet, but since the door goes horizontal this is equivalent to raising the whole door for half that distance, or about 3.75 feet. So if the door weighs, say, 150 lbs, then the energy supplied by the springs is 3.75 * 150, or about 563 foot-pounds. This is like throwing a 50-lb sack of cement up a 11-foot flight of stairs. Or catching a 50-lb sack of cement dropped from 11 feet up.

We are a family owned and operated, local garage door company in the Carlisle area that believes in attention to detail and an emphasis on customer service and satisfaction. We even offer same-day service because we know that when your garage door isn’t working the way it should, you need it fixed fast. We offer affordable rates that will fit your budget, and we’re confident you won’t find another garage door installation company in Carlisle or the surrounding areas with the same dedication to our customers and the quality of our work at the affordable rates we offer our clients.
This is the electric opener which operates this door. I'm picturing it here because you pull the rope to disconnect the trolley, run the trolley under power to the fully-open position, and then disconnect power before working on the door. Then you should lock the door down with either the security lock or with Vise-Grips or C-clamps. This avoids the door lifting when you don't expect it as you are applying spring adjustments. It you were to foolishly overwind the spring without the door locked down, you could possibly find the door trying to leap up to the raised position when you aren't prepared. That would likely knock your grip off the winding rods, with potentially disastrous results. I like to work under the safety principle that serious accidents should be physically possible only when you make two or more stupid mistakes at the same time.
If you’re looking for a stylish garage door that is a statement of your good taste, we have customized solutions that fit your family’s lifestyle. Or if it’s the safety and security of an integrated, commercial door and operator system that your workplace needs, Overhead Door™ products make operating your facility safer and easier. Our products are manufactured to give you durable, long-lasting performance for years of extended use and trouble-free operation. Each product, from residential to industrial to commercial applications, is backed by knowledgeable and professional customer support for troubleshooting and answers to your questions.
The first garage door opener remote controls were simple and consisted of a simple transmitter (the remote) and receiver which controlled the opener mechanism. The transmitter would transmit on a designated frequency; the receiver would listen for the radio signal, then open or close the garage, depending on the door position. The basic concept of this can be traced back to World War II. This type of system was used to detonate remote bombs. While novel at the time, the technology ran its course when garage door openers became popular. While the garage door remote control transmitter is low power and has limited range, its signal can be received by other, nearby, garage door openers. When two neighbors had garage door openers, then opening one garage door might open the neighbor’s garage door as well.
Follow the manufacturer’s instructions to assemble the opener and mount the rail to the header bracket above the door. Then set the opener on a ladder where you’re going to install it. The ladder (usually an 8-footer) holds the opener in position while you measure for your lengths of angle iron. If necessary, put boards under the opener to raise it.
If you have a steel door, but want the look of a wood one, it is not necessary to change your entire garage door. Often, it may be possible to mimic the look of wood with skillful painting. Your local home improvement store may be able to provide good advice about the type of paint and brushes needed to mimic the look of wood for your particular door material.
Screw-drive garage door openers aren't as popular as some other types, but feedback indicates that those that give the Genie Excelerator a try are largely very happy that they did. It's a fast performer, owners say, and the company claims that it can move a door at a rate of up to a foot per second. It's relatively quiet, too -- perhaps not the absolute quietest that you can buy, but certainly quieter than a chain-drive opener, and quieter than older screw-drive openers, users report.
In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the project yourself, but you should recruit help for removing the old door.
Though you can do some maintenance to your garage doors on your own, it may be a good idea to schedule routine inspections with a professional. A typical service call will include a manual inspection of the door and opener. Then adjustments can be made including spring tension, chain/belt tension, limits and force adjustments and door lubrication. Fees for this service vary from place to place, but garage door repairs typically cost between $147 and $340.

You garage door is one of your primary entrances to your home so you want to know that they are functioning properly at all times. If you are having complications with your current garage door, then you need to hire a professional garage door company to determine if it needs to be repaired or replaced. Included are the average garage door repair costs in 2016, for the United States. This is the latest information headed into the new year and is a great guide for 2017. I've also included some garage door repair costs pictures, graphics and graphs that include high, low and average costs for garage door repair, installation and replacement costs. It also includes garage door part repair and replacement costs.
Sectional: Also known as a raised panel door, this door is the most common. It is made of several horizontal panels hinged together, fitted with wheels and mounted within a track. The biggest advantage of this door is it takes up relatively little space and easily controlled with a standard remote garage door opener for a nominal cost. Their moving parts are readily accessible which can keep repair costs low. The average cost for sectional door repairs is $128.

Ryan came to my rescue within 6 hrs of my call. He was professional, knowledgeable, friendly, and very thorough. He got my door up and running after figuring out what 3 others could not! Don’t try and go the cheapest route like I did because you’ll end up wasting time and money. Hire the pros like Ryan FIRST! If I ever need someone in the future, I’ll be calling them first thing! HIGHLY RECOMMENDread more
Most wood doors are sectional roll-up doors, though a swing-up wood door that’s meant to be painted can be affordably built in the driveway from a wood framework and plywood. Custom wood doors are typically made of durable softwoods such as Douglas fir, cedar, redwood or cypress, or from hardwoods such as oak or mahogany. Appearance-grade hardwoods are relatively expensive.
Trading wire size for length, diameter, or cycle life: Now we are really going to save you some money, if you just recall your high school algebra class (and I don't mean that cute cheerleader who sat next to you). If you further understand the role of the 4th power of the spring wire size (letter d in the formulas above) in the numerator of the spring rate formula, and how to increase or decrease d to compensate for changes in length, diameter, and cycle life, then you're qualified for elite spring calculations. Matching springs is a matter of equating the 4th power of the proportion in wire size change to the proportion of change in the diameter or length or the product of both diameter and length. However, it is usually best to only increase wire size when substituting a spring, since this does not derate the cycle life. If you observe that the formula for bending stress is proportionate to the inverse 3rd power of the diameter, then physically a proportionate increase in wire size will result in a dramatic increase in cycle life of the 3rd power of that proportion. Trade-off example: Yawn with me while we ponder my original spring once more. Let's say I was in a fit of engineering mania, and wanted to replace my spring having a 0.2253 inch diameter wire (d = 0.2253) with a 0.262 wire version (d = 0.262). How much longer is the spring with equal torque rate, assuming we use the same coil diameter? The proportion of this change is 0.262/0.2253 = 1.163, and the 4th power of that is 1.83. This means the length must increase by a factor of 1.83 (again, not counting dead coils). Recalling that the length in Example 1 was 102 non-dead coils, the heavier wire spring must be about 1.83*102 = 187 coils, which when adding 5 dead coils and multiplying by the wire size to get the overall length, is (187+5)*0.262 = 50 inches, versus 24 inches in the original. So using this heavier wire more than doubles the length (and thus the mass and thus the cost). While the cost about doubles, the stress goes down by the inverse 3rd power of the wire size proportion, or 1/(1.163**3) = 0.64. Sress is favorably, non-linearly related to cycle lifetime (halving the stress more than doubles the lifetime), so this decreased stress should more than double the expected lifetime of the spring. While the up-front cost is more, the true cost of an amortized lifetime is much less. In short, per cycle it is cheaper. Ah, the wonders of engineering calculations! Conclusion: Observe that the stress formula (and thus the cycle lifetime) depends only on wire diameter (d) for equal torques. Thus the only way to improve cycle lifetime is to use heavier wire. For equal torques, heavier wire size, due to the exponents in the formulas, increases cycle lifetime much faster than it increases mass (and thus cost), physically speaking.

Even if one could somehow stretch and clamp the springs to the proper extra length, the process would still be more trouble, and there would be little or no reduction of risk. Lifting the full weight of the unsprung door by hand and clamping it in the raised position is dangerous in itself, and creates the same amount of stored energy as winding the springs, ready to slip out of your hands. Many doors won't travel far enough up the track to provide clearance to access the springs. You're also going to have to deal with winding stiff steel cables onto both lift drums at once without any resistance to maintain tension. Finally, even if you managed to complete the installation with the door raised, you then have to lower the massive door against an untested balancing torque. If you've made a mistake, then that massive door has nothing but your skeletal force applied through your meat clamps (hands) to prevent it from falling down and crushing whatever is in the way (perhaps your feet?).
For garage doors with windows, try to match the glass style of your house windows to provide a more consistent look. It’s also recommended that you install insulated windows if your garage is heated or air conditioned. If you opt for an uninsulated garage door, make sure it’s made of thick steel – specifically 24-gauge. Thicker steel will help prevent dents.

Garage doors are the largest moving object inside your home. If you have a problematic garage door, it compromises the safety of your family and home. Ankmar Denver is a professional company you can count on. We provide you with quality service at a reasonable price. We offer FREE estimates on replacement garage doors and are spring replacement specialists. 24 hours a day 7 days a week we are your number one garage door repair service.
It you have a tilt-up door, you are looking at a $150 - $200 repair or replacement. If it's a roll-up door it's going to cost you more. Roll-up door spring repair or replacement is usually around $200 - $250 for a 2 car door. If the brackets need to be disassembled to remove the springs due to the shaft not sliding sideways enough it will cost you an additional $50 - $100.
Depending on the design, you can know in advance how many turns are going to have to be unwound. Lifting a 7-foot door by winding a cable on a 4-inch diameter (about 1 foot circumference) drum requires about 7 turns, plus one extra turn to maintain cable tension at the top-of-travel. Maintaining tension at the top-of-travel is critical; without it the cable will jump off the drum, requiring a serious repair.
Most electric garage door openers have two lights: one in front of the opener and one behind or sometimes they sit side by side. They should provide enough light for you to get into your home from your car. Generally, people don’t leave the garage light on when it’s not in use, so it’s nice to have a temporary light when you arrive home. The length of time the light stays on varies according to how it is programmed. In most instances, you don’t need more than a few minutes from the time you leave the car to when you enter your home.
Annual maintenance. Make an annual check of all nuts and bolts on rails and rollers to make sure they’re firmly tightened. Check the condition of all cables to make sure they’re not worn or frayed. Lubricate rollers and springs with a garage-door lubricant (see How to Fix a Noisy Garage Door for maintenance and problem-solving tips). The door should operate smoothly and be properly balanced. Check the balance by disconnecting the opener and lowering the door halfway- the door should hold its position. If it doesn’t, adjust the spring tension or replace the springs.
The replacement springs in my case proved to be 0.2253 wire size, 2.0 inch (inside) diameter, and 24 inches long, in a pair of one left- and one right-hand winding. Actually, the old springs in these pictures were a slightly smaller size, but another similar door on this garage was better balanced by that size. Whoever installed the old springs didn't quite get the weight and size just right; it is not unusual to find a repair service installing a slightly off-balance spring size that happened to already be on the truck during the service call. My electric opener had no trouble handling the small imbalance. But since it is safer to reduce the electric operating force as much as possible through careful balancing, I chose the size that was working better on the other door. The Chamberlain brand electric openers (also sold by Sears) I have incorporate a plastic worm gear that tends to wear out after some years of use, requiring a disassembly and installation of a $20 repair kit; this wear is minimized by a properly balanced door.

If you have a steel door, but want the look of a wood one, it is not necessary to change your entire garage door. Often, it may be possible to mimic the look of wood with skillful painting. Your local home improvement store may be able to provide good advice about the type of paint and brushes needed to mimic the look of wood for your particular door material.


The third stage of garage door opener technology uses a frequency spectrum range between 300-400 MHz and rolling code (code hopping) technology to defeat code grabbers. In addition to transmitting a unique identifier for the remote control, a sequence number and an encrypted message are also sent. Although an intruder could still capture the code used to open a garage door, the sequence number immediately expires, so retransmitting the code later would not open the garage door. The encryption makes it extremely difficult for an intruder to forge a message with the next sequence number that would open the door. Some rolling code systems are more involved than others. Because there is a high probability that someone will push the remote's button while not in range and thus advance the sequence number, the receiver does not insist the sequence number increase by exactly one; it will accept a sequence number that falls within a narrow window or two successive sequence numbers in a much wider window. Rolling code technology is also used on car remote controls and with some internet protocols for secure sites.

And for some extra features, you'll appreciate accessing the system through the MyQ smartphone app. You can set up this Chamberlain opener to automatically close the door after 1, 5, or 10 minutes, which is great for people who are a bit forgetful. We also really like the motion-detecting control panel, which turns on lights whenever it records nearby movement.

Garage Door Repair

×