We are a family owned and operated, local garage door company in the Carlisle area that believes in attention to detail and an emphasis on customer service and satisfaction. We even offer same-day service because we know that when your garage door isn’t working the way it should, you need it fixed fast. We offer affordable rates that will fit your budget, and we’re confident you won’t find another garage door installation company in Carlisle or the surrounding areas with the same dedication to our customers and the quality of our work at the affordable rates we offer our clients.
Here is what a winding cone looks like without the spring. The threads that grip the inside of the spring coils are ambidextrous, so you can use the same part on either right- or left-hand-wound springs. The cone size is specific for a certain inner diameter of springs, so if you have the wrong size, the cone will slip inside the spring (cone too small), or not fit (cone too big).
You'll never ask yourself that question again. Just look at your phone to know for sure. Most smart garage door openers will tell you if it's open or shut. They'll send a message every time your garage door is opened or closed too, if you like. Electric garage door openers provide a huge amount of convenience and safety. Imagine you're in a hurry, it's raining out, you pull out of the garage then press the button on your garage door opener remote. The garage door closes, and you didn't have to get out of your car.
A torsion spring counterbalance system consists of one or two tightly wound up springs on a steel shaft with cable drums at both ends. The entire apparatus mounts on the header wall above the garage door and has three supports: a center bearing plate with a steel or nylon bearing and two end bearing plates at both ends. The springs themselves consist of the steel wire with a stationary cone at one end and a winding cone at the other end. The stationary cone is attached to the center bearing plate. The winding cone consists of holes every 90 degrees for winding the springs and two set screws to secure the springs to the shaft. Steel counterbalance cables run from the roller brackets at the bottom corners of the door to a notch in the cable drums. When the door is raised, the springs unwind and the stored tension lifts the door by turning the shaft, thus turning the cable drums, wrapping the cables around the grooves on the cable drums. When the door is lowered, the cables unwrap from the drums and the springs are rewound to full tension.[7]
In 1921, C.G Johnson invented the upward-acting garage door and revolutionized the way the world entered their homes. For more than 97 years, Overhead Door™ garage doors have been securing and providing families access to their homes. Overhead Door™ garage doors are assembled in the United States and sold at over 450 authorized Ribbon Distributors throughout North America. The Overhead Door™ brand and Overhead Door™ distributors are synonymous with quality and dependability. To ensure you are getting the genuine, the original, make sure to always look for the Red Ribbon.
Step 5: Check for loose hardware, and tighten as needed. On swing-up doors, check the plates where the spring is mounted to be sure the screws are tight, and tighten any loose screws. On roll-up doors, check the hinges that hold the sections of the door together; tighten any loose screws, and replace any damaged hinges. Sagging at one side of the door can often be corrected by servicing the hinges. If a screw hole is enlarged, replace the screw with a longer one of the same diameter, and use a hollow fiber plug, dipped in carpenters' glue, with the new screw. If the wood is cracked at a hinge, remove the hinge and fill the cracks and the screw holes with wood filler. Let the filler dry and then replace the hinge. If possible, move the hinge onto solid wood.

Most garage door openers are pretty expensive. So if you need an opener on a budget, the Genie 1035-V (also known as the Genie Chain Drive 500) gives you that desirable low price point. It doesn't have a lot of high-end tech features, nor will it manage heavy garage doors, but it does the basic work of raising and lowering the garage door perfectly well.


Clopay Garage Doors featuring Intellicore insulation technology represent Clopay Garage Doors featuring Intellicore insulation technology represent the ultimate smart choice for homeowners. Clopay Intellicore is proprietary polyurethane foam that is injected into a garage door expanding to fill the entire structure. The result is a door with incredible strength and durability. Its dense insulation also produces a quieter ...  More + Product Details Close

I repeat my caution about the uncertainty of interpreting color codes. A professional installer reading this page emailed me to say that the red color indicates the springs are right-hand windings, not the DASMA color code for the wire size. But this photo shows both a right- and a left-hand spring, and both have the red paint on the cones and set-screws. I conclude it is prudent to make your own measurements and analysis. Do not rely on the colors on old installations. The only time I would respect them would be on new parts that carried documentation giving the code.


You might not think it could get easier than pushing a big button to open a door, but some garage door openers make things even simpler by offering keyless entry and multiple remotes. Many models come with a keyless entry pad that mounts outside the garage door so you can gain access without a remote. While a remote is preferable for most situations, there are times when you need to get into the garage and don’t have it handy, so this is a nice feature to have.
At PK Garage Door, we firmly believe that an installation properly done is the key to a top-performing garage door system. Well-experienced, we understand and follow the highest safety standards in the industry. In addition, Garaga has certified our company as one of their Garaga Expert dealers, which means we meet their strict criteria for technical expertise and professionalism.    
I could not be happier with the service from Precision, and Tom, especially. About a year and a half ago I called to have my garage door that was sticking, repaired. Tom came out same day and replaced, adjusted, serviced all moving parts and got it going smoothly. He has since come out within hours of a call to adjust and keep (what might not be the best) door, (originally installed by someone else), operating well. I recommend Precision and Tom with complete confidence.
Next, the torsion shaft is reassembled with the new springs, the drums repositioned loosely on the shaft, this whole assembly slid back into the end bearings, and the drum set-screws tightened down. I tightened the set-screws about 1/2 or 3/4 of a turn after contact with the shaft, which provides a good grip, but does not distort the shaft. The drums can be set on their old positions, if they were correctly installed, which is snug up against the end bearings to remove any longitudinal play in the torsion shaft. Now the lift cable can be reattached to the drums, and a slight temporary torque applied to the shaft to keep the cable taut while the first spring is wound. This temporary torque is conveniently applied with a pair of locking pliers clamped on the shaft, positioned such that they hold the torque by pressing lightly against the wall above the door, before you start the spring winding, The locking pliers stay on the torsion shaft until you have finished the spring winding locked down the spring cone(s) with the setscrew(s), and removed the winding bars. Then you simply remove them with the release on the wrench handle. I feel that any job that doesn't require a trick manipulation with either locking pliers or duct tape (or in the ultimate case, both!) is just too boring. My trusty pliers look a trifle rusty ever since I used them to clamp something on my outdoor TV antenna "temporarily" and left them out in the weather for, oh, several years. The white stuff on the drum is paint overspray from the original painting of the garage interior.
Clearly there is a lot going on with your garage door and it takes trained and qualified experts to properly install, maintain, repair, and replace them. The experts and On Track Garage Door Services have the tools, skills, training to get your garage door fixed the first time. In addition we can help you fix your garage door affordably and offer many options from your basic garage door to custom wood styles. To find out how much your garage door repair will cost, give us a call at 480-641-2301 or use our Contact Page.

However, in addition to potentially causing injuries to the under-prepared DIYer, a malfunctioning door can become a safety hazard to you and your family. Keep in mind, according to the National Electronic Injury Surveillance System (NEISS), over 13000 people checked into hospitals with garage related injuries in the United States in 2007. You don’t want to turn a loved one into a statistic just to save a few dollars!
If you've researched this subject at all, you will no doubt have heard that you shouldn't be attempting torsion spring replacement as a do-it-yourselfer. That is generally good advice, so if you have any doubts about your abilities to do risky physical work on your own, hire the job out like everyone else. I found I was capable of doing this work with acceptable risk, because I intelligently understood the techniques, paid careful attention to methods and safety, knew how to use common tools in good condition, properly improvised the special tools I didn't have, and diligently attended to correctly performing a few moments of hazardous manipulation. I learned to do it purely on my own based mostly on bits of advice reluctantly given in Internet forums such as the Usenet newsgroup alt.home.repair. When I first wrote this page in 2002, there was no other do-it-yourself information available on the Web, and it was not until 2005 that reliable information disclosing the techniques started to appear elsewhere (see links below).

Now 13 pounds of force must be respected when backed by many hundreds of foot-pounds of stored energy, waiting to be released. Holding this torque is equivalent to stalling a 3 horsepower DC motor. But holding and turning these handles does not require extraordinary human strength. Note that this maximum tangential force depends only on the weight of the door, and the radius of the drums, and is divided by the number of springs (some designs have only one longer spring, as mine did originally, instead of two shorter ones). Higher or lower lift distances imply more or less turns to wind the spring (and thus a different spring geometry), but not more force on each turn.
Two of the spring references specifically for the garage-door industry are the APCO Spring Manual by Bill Eichenberger, and the Torsion Spring Rate Book by Clarence Veigel; these give tables of spring sizes and torque constants. Spring engineering principles in general are described in the Handbook of Spring Design published by the Spring Manufacturer's Institute; the formulas allow you to calculate torque constants knowing only the geometry and the Young's modulus of the material. You can also find some brief spring information in standard references like Machinery's Handbook and Marks' Standard Handbook for Mechanical Engineers.

Our team of 100-plus technicians and service representatives takes care of you every step along the way. Our technicians are the best in the area. They’ll provide expert guidance as you consider your options, and then top-notch service to complete the repairs. When you want Cincinnati or Northern Kentucky garage door repair you can trust, choose AE Door & Window.
The Ryobi Ultra-Quiet Garage Door Opener boasts a The Ryobi Ultra-Quiet Garage Door Opener boasts a 2HPs motor giving you faster openings and prolonging motor life. An integrated long-lasting LED light keeps your garage illuminated and ensures you don’t spend time changing out light bulbs. Download the Ryobi Garage Door Opener App to monitor and control your garage ...  More + Product Details Close
×